• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1714-1719
• /
• 2003

Antilock Brake System (ABS) is indispensable safety equipment for vehicles today. In order to develop new ABS ECU suitable for pneumatic brake system of a bus, a Hardware In-the-Loop Simulation (HILS) System was developed. In this HILS, the pneumatic brake system of a bus and antilock brake component were used as hardware. For the computer simulation, the 14-Degree of Freedom (DOF) bus dynamic model was constructed using the Matlab/Simulink software package. This model was compiled and downloaded in the simulation board, where the Power PC processor was used for real-time simulation. Additional commercial package, the ControlDesk was used to monitor the dynamic simulation results and physical signal values. This paper will focus on the procedure and results of evaluating the ECU in the HILS simulation. Two representative cases, wet basalt road and $split-{\mu}$ road, were used to simulate real road conditions. At each simulated road, the vehicle was driven and stopped under the help of the developed ECU. In each simulation, the dynamical behavior of the vehicle was monitored. After enough tests in the laboratory using HILS, the parameter-tuned ECU was equipped in a real bus, which was driven and stopped in the real test field in Korea. And finally, the experiment results of ABS equipped vehicle's dynamic behavior both in HILS test and in test fields were compared.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.559-564
• /
• 2014

A microgrid as a small scale power system is operated by the grid-connected mode and islanded mode. It is anticipated that the battery energy storage system (BESS) is able to be applied to the microgrid for stable power control, such as tie-line and smoothing control in the grid-connected mode and voltage and frequency control in the islanded mode. In this paper, a digital signal processor (DSP), Two BESS controllers based on TMS320F28335 of a microgrid are implemented and are tested to show control performance in the hardware-in-the loop simulation (HILS) system.

• Journal of the Korea Society for Simulation
• /
• v.28 no.4
• /
• pp.11-20
• /
• 2019

This paper presents a HILS(Hardware-In-the-Loop Simulation) approach for the verification of the OHT (Overhead Hoist Transport) controller in a semiconductor FAB. Since hundreds of OHTs can run simultaneously on the OHT network of a FAB, the full verification of the OHT controller is very essential to guarantee the stableness of the material handling system. The controller needs to fully consider not only normal situations but also abnormal situations that are difficult to predict. For the verification of the controller, we propose a HILS approach using a virtual environment including OHTs on a rail network, which can generate abnormal situations. The proposed HILS approach has been implemented and tested with various examples.

• Journal of Wind Energy
• /
• v.15 no.1
• /
• pp.60-68
• /
• 2024

In this study, a hardware-in-the-loop simulation (HILS) environment was established using MATLAB/Simulink to simulate and verify the power performance of a wind turbine. The target wind turbine was selected as the NREL 5 MW model, and modeling was performed based on the disclosed specifications. The HILS environment consists of a PC equipped with a MATLAB/Simulink program, a programmable logic controller (PLC) for uploading and linking control algorithms, and data acquisition (DAQ) equipment to manage wind turbine data input and output. The operation of the HILS environment was carried out as a procedure of operation (PC) of the target wind turbine modeled based on MATLAB/Simulink, data acquisition (PLC) of control algorithms, control command calculation (PLC), and control command input (PC). The simulation was performed using the HILS environment under turbulent wind conditions and compared with the simulation results performed under the same conditions in the HILS environment using the commercial program Bladed for performance verification. From the comparison, it was found that the dynamic simulation results of the Bladed HILS and the MATLAB HILS were close in power performances and the errors in the average values of rotor rotation speed and power generation between the two simulations were about 0.44 % and 3.3 %, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.216-219
• /
• 2021

In the Eco-Friendly Ship Act, the shaft generator is an equipment for eco-friendly ships. However, in order to apply the new technology in ships, high reliability is required, and the HILS (hardware in loop system) test is used as a verification method for this. Therefore, in this paper, a shaft generator is modeled and simulated for HILS test of a tugboat to which a shaft generator is applied. Through simulation, it was verified that the charging/discharging of the shaft generator operates according to the scenario.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.339-340
• /
• 2015

본 논문에서는 HVDC 제어 시스템의 기능 검증을 위해 구축한 RTDS 기반의 HILS(Hardware-In-the Loop Simulation)시스템 및 시험 결과를 소개하였다. MMC 기반 VSC HVDC는 다수의 직렬 연결된 SM(Sub-Module)을 개별 제어해야 하므로 기존의 LCC HVDC 및 2/3-Level 컨버터 기반의 VSC HVDC와 같은 설비들보다 훨씬 더 복잡한 VBE 구조를 가지고 있다. 또한 짧은 시간 내에 정밀한 제어가 가능해야 하므로 높은 제어 정밀도가 요구된다. (주)효성에서는 제어 시스템의 성능 검증을 위해 RTDS 기반의 HILS(Hardware-In-the Loop Simulation)시스템을 구축하였으며, 이를 이용하여 HVDC 제어 시스템의 성능 시험을 수행하였다. 본 논문에서는 구축된 RTDS 기반의 HILS 시스템 및 시험 결과를 소개하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.5
• /
• pp.447-454
• /
• 2015

Design and application of hardware-in-the-loop simulation (HILS) for design of CNC-controlled machine tool feed drives is discussed. The CNC machine tool is a complex mechatronics system where the complexity results from the software-based controller composed of a variety of functionalities and advanced control algorithms. Therefore, using a real CNC controller in the control simulation has merits considering the efforts and accuracy of the simulation modeling. In this paper challenges in HILS for a CNC controlled feed drive, such as minimization of time delay and transmission error that are caused by discretization of the feed drive model, is elaborated. Using an experimental HILS setup of a machine tool feed drive applications in controller gain selection and CNC diagnostics are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.135-140
• /
• 1992

This paper presents the configuration, HILS procedure and performance simulation results of the RPV autopilot including a strapdown AHRS. Real time hardware-in-the-loop simulation was performed by using a 3 axis flight motion simulator alonged assumed flight trajectory of the RPV. Being compared with the result of the 6 DOF simulation, the HILS results showed that the performance of the autopilot was satisfactory.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.4
• /
• pp.638-647
• /
• 1994

This paper describes the real time Hardware-In-the Loop Simulation(HILS) that is an efective tool for design, testing and performance evaluation of the guidanc eflight system. The real time HILS was performed by using a 3-axis flight motion simulator, real time computer, I/O system and flight control system hardware along with the assumed flight trajectory of the guidance flight system. Also, we proved the validity of the real time HILS is the guidance flight system by comparing its simulation results with the software simulation data and telemetry data.

• Aerospace Engineering and Technology
• /
• v.3 no.1
• /
• pp.170-178
• /
• 2004

This paper deals with six degree-of-freedom HILS(hardware-in-the-loop-simulation) of KSR-III rocket using a TAFMS(three axis flight motion simulator). This TAFMS HILS test is accomplished before main HILS tests in order to verify the control stability in the presence of TAFMS dynamic effects. The TAFMS HILS test includes initial attitude holding tests for INS initial alignment procedures, timer synchronization tests with an auxiliary lift-off signal, real-time calibration tests using an external thermal recorder, open-loop TAFMS operating tests, and final closed-loop TAFMS HILS tests using the TAFMS attitude measurements as inputs to the closed control loop. The HILS tests are accomplished for several flight conditions composed with nominal flight condition, TWD effect added condition, slosh modes and/or bending modes existing condition, and windy condition, etc.