• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.63-69
• /
• 2006

In a traditional society, building materials were developed fulfilling the requirements of conveniences and functionalities such as safety, construction work, durability and economical efficiency. However, as the concern about environmental or users' health issues has been elevated recently, research and development about eco-friendly material are alto vigorously promoted further In addition, thanks to the steady growth of domestic industry, the amount of discharged industrial by-product is getting increasing. However, its recycling rate remain at low level as most industrial by-products are filled up in the land, which worsen the environmental pollution. Zeolite powder is cement admixture and is expected to have constraining effect of factors causing symptoms of inhabitants in a new house and alleviates the amount of discharged harmful elements emitted from hardened cement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.461-464
• /
• 2005

As the research on the development of the lightweight concrete block by the hydro-thermal synthetic reaction mixed with the calcareous material and bottom ash that is used less among siliceous material, we studied on the physical and chemical characteristics in the changes of hydro-thermal synthetic reaction of lightweight concrete block compounded with the PP fiber to increase flexural toughness and to prevent fragility failure. The results of the experiment are as follow. According to the increase of hydro-thermal synthetic reaction and the fiber content, compressive and flexural strength increased. Despite the changes of the hydro-thermal synthetic reaction time, tobermorite was produced on each of the specimens similarly. However, the phase of tobermorite was changed in accordance with the changes of time. Also, $CaCo_{3}$ appeared on the surface of the 9 hour hardened specimen.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.69-72
• /
• 2000

In this paper, the electrical properties due to epoxy resin used in transformer of rail road signal are studied. The specimen of epoxy resin was hardened as each 3[h], 4[h], 5[h] in this experiment. In order to measure the conductivity properties, the highmegohm meter is used at temperature 25 to 140[$^{\circ}C$] and applying voltage 100 to 1000[V]. As a result of this experiment, we confirmed that 3[h] specimen is better than the others.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.132-133
• /
• 2007

반도체 소자의 제조 공정 기술이 발전하고 초고집적화가 됨에 따라 소자 선폭도 급속하게 감소하였다. 이로 인하여 기존의 식각 공정에서 식각 후 남은 잔여 Photoresist residue는 소자 생산에 큰 영향이 없었으나 현재 이러한 잔여물은 초고집적 소자에 치명적인 문제를 발생시킬 수 있다. 본 실험에서는 세정액 분자에 플라즈마 충격을 가하여 세정액을 활성화함으로써 기존의 세정액과의 세정능력을 비교 분석하였다.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.1
• /
• pp.15-23
• /
• 2023

The grouting method is a method of construction for the purpose of waterproofing and reinforcing soft ground. When grout is injected into the ground, there are various types of penetration and diffusion of grout depending on the shape of the ground, the size of soil, the porosity, and the presence or absence of groundwater. the current situation. Therefore, in this study, to investigate the penetration performance of the grouting to conductive material, laboratory tests were performed on the addition of the conductive material. In the injection test, 0%, 3%, and 5% of the mixed water were added as conductive materials to the grout, and the original ground condition was composed of various types of ground composed of gravel and silica sand. Conductive grout is injected by pressure into the model ground using a dedicated injection device, and the injection time (t), pressure (p), flow rate (v) and injection amount (q) are measured, and the hardened body injected in the model ground is collected. Penetration performance was evaluated. In the results of the grout injection experiment, the amount of conductive material used and the grout injection rate showed an inverse relationship, and it was confirmed that the penetration pattern was changed according to the size of the soil particles in the model ground. The grout containing the conductive material has relatively good penetration into the ground and excellent strength and durability of the hardened body, so it was judged that it could be used as an additive for measuring the penetration range of the grout.

• Korean Journal of Materials Research
• /
• v.20 no.2
• /
• pp.60-64
• /
• 2010

This study looked at high performance copper-based alloys as LED lead frame materials with higher electrical-conductivity and the maintenance of superior tensile strength. This study investigated the effects on the tensile strength, electrical conductivity, thermal softening, size and distribution of the precipitation phases when Cr was added in Cu-Fe alloy in order to satisfy characteristics for LED Lead Frame material. Strips of the alloys were produced by casting and then properly treated to achieve a thickness of 0.25 mm by hot-rolling, scalping, and cold-rolling; mechanical properties such as tensile strength, hardness and electrical-conductivity were determined and compared. To determine precipitates in alloy that affect hardness and electrical-conductivity, electron microscope testing was also performed. Cr showed the effect of precipitation hardened with a $Cr_3Si$ precipitation phase. As a result of this experiment, appropriate aging temperature and time have been determined and we have developed a copper-based alloy with high tensile strength and electrical-conductivity. This alloy has the possibility for use as a substitution material for the LED Lead Frame of Cu alloy.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2002.11a
• /
• pp.67-76
• /
• 2002

Self-leveling material(SLM) is one of the floor finishing materials which make flat surface like as water level by itself in a short time. So it is possible to increase construction speed and enhance economical efficiency. In this study, author intended to develop SLM for the industrial warehouse and factory loading heavy weight machinery and vehicles. The demanded properties for this type of SLM are above 20mm of flow value and above 300kgf/cm2 of 28-days compressive strength. To possess demended strength and fluidity, SLM have to be composed of many types of binders and chemical additives. So it is difficult to decide suitable mixing proportion of composition materials. In this study, author investigated the weight percentage effect of main composition materials for high-strength self-leveling material, by experimental design such as tables of orthogonal arrays and simplex design, and by statistical analysis such as analysis of variance and analysis of response surface. Variables of experiments were ordinary portland cement(OPC), alumina cement(AC), anhydrous gypsum(AG), lime stone(LS) and sand, and properties of tests were fluidity of fresh state and strength of hardened state. Results of this study are showed that suitable mix proportions of binders for the high strength self-leveling materials are two groups. One is 78~85.5% OPC, 7.5~9.5% AC, 9~12.5% AG and the other is 72.5~78% OPC, 9~12.5% AC, 13~l5% AG.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.6
• /
• pp.339-344
• /
• 2009

Recently, Laser surface treatment technologies have been used to improve wear charactenitics and fatigue resistance of metal molding. When the laser beam is irradiated on the surface and laser speed is appropriate, the laser focal position is rapidly heated and the thermal energy of surface penetrates the material after irradiation, finally imbuing it with a new mechanical characteristic by the process of self-quenching. This research estimates the material characteristic after efficient and functional surface treatment using HPDL, which is more efficient than the existing CW Nd:YAG laser heat source. To estimate this, microstructural changes and hardness characteristics of three parts (the surface treatment part, heat affect zone, and parental material) are observed with the change of laser beam speed and surface temperature. Moreover, the depth of the hardened area is observed with the change of the laser beam speed and temperature. From the results of the experiments, it has been shown that the maximum hardness is approximately 788Hv when the heat treatment temperature and the travel speed are $1150^{\circ}$ and 2 mm/sec, respectively.

• Nuclear Engineering and Technology
• /
• v.43 no.5
• /
• pp.459-468
• /
• 2011

The current solution to the problem of using cementitious material for sealing purposes in a final radioactive waste repository is to develop a low-pH cement grout. In this study, the material properties of a low-pH cement grout based on a recipe used at ONKALO are investigated by considering such factors as pH variation, compressive strength, dynamic modulus, and hydraulic conductivity by using silica fume and micro-cement. From the pH measurements of the hardened cement grout, the required pH (< pH 11) is obtained after 130 days of curing. Although the engineering properties of the low-pH cement grout used in this study are inferior to those of conventional high-pH cement grout, the utilization of silica fume and micro-cement effectively meets the long-term environmental and durability requirements for cement grout in a radioactive waste repository.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.9
• /
• pp.1508-1516
• /
• 2003

In numerical analysis for hydroforming process, the stress calculation is effected by flow stress which is general obtained by stress-strain relationship from uni-axial tension test, so the result of the analysis, especially in tube hydroforming, has limitation of accuracy, tubes are made in roll-forming process and become work-hardened. Then roll forming process causes material properties between rolling direction and circumstantial direction of the tube to be different. So it is difficult to predict material behavior in the process condition of bi-axial stress state. In this study, the flow stress of the tube is determined by inverse engineering approach and bulge test that is widely used for formability test in the condition of bi-axial stress. And Hill's quadratic yield function and flow rule are used to consider the anisotropy of the tube in the roll forming process.