• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.1
• /
• pp.66-72
• /
• 2016

The aim of this paper is to investigate the characteristics of the signal of local ice load acting on side shell in the bow part due to ice broken by an icebreaker in ice-covered waters. The Korean icebreaking research vessel "ARAON" voyaged to the Arctic Ocean during the summer of 2010, and measurements of local ice load were carried out using several strain gauges. In this study, the time history of measured signals was analyzed and the characteristic values including rising time and half-decaying time were presented using non-dimensional parameters.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.4
• /
• pp.306-312
• /
• 2018

To navigate in ice-covered waters, the ice-breaking process is required. The ice-breaking mode depends on material properties of sea ice and ice conditions. The ice-breaking mode is classified into ramming and continuous ice-breaking. The ramming is effective on large ice features, such as thick ice ridge and icebergs, and the continuous ice-breaking is on level ice. In general, the impact time duration of crushing or bending on ice sheets is from 0.2 to 1.0 second. However, impact duration in ramming will be increased. The Korean ice-breaking research vessel ARAON conducted her research voyage in the Antarctic sea during the winter of 2012. The IBRV ARAON measured strain in ramming and continuous ice-breaking. Strain gauge signals were recorded during the planned ice-breaking performance and the unplanned ice transits in heavy ice conditions. The aim of this study is to investigate the ice load signals measured in ramming processes under the heavy ice condition. Based on the time history of the signals, a raising time, a half-decaying time and time duration were investigated and compared with the previous study which was suggested the five profiles of the ice load signals.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.56-62
• /
• 2014

When fault currents contain decaying DC offset, the peak value of the fault current in the first cycle of the fault period is higher than the fault current during the steady-state period. To reduce the asymmetric fault current, this paper proposes an operation scheme using the series connection of two hybrid type Superconducting Fault Current Limiters (SFCLs) : an auxiliary SFCL and a main SFCL. The proposed method calculates the fault angle by comparing the zero-crossing time with fault detection time. According to the fault angle calculated, an auxiliary SFCL operates to reduce an asymmetric fault current during half a cycle after fault occurrence. After this process, the fault current is limited by a main SFCL. To confirm the usefulness of the proposed method, case studies using Electro-Magnetic Transients Program (EMTP)/Alternative Transient Program (ATP) Draw are perfomed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.1
• /
• pp.98-107
• /
• 2017

Electric components equipped with naval shipboards must endure mechanical shock caused by various mechanical impulsive sources. Thus the components must be designed carefully and reliability test is an essential procedure before use. In this study, a new design technology applicable to a large and heavy shock generation system which can generate various specific real mechanical shocks in specified time domain was introduced. Commonly, the shock transmitted through the wall of naval shipboard consists of dual shocks. The primary shock is of a very high amplitude and very short period half-sine form. The following shock is of an exponentially decaying harmonic form of relatively longer period. Based on the different dynamic characteristics of two shocks, we proposed a sequential design procedure to determine spring and damping coefficients of the generation system. Some numerical simulation results showed the feasibility of the proposed method.

• Journal of Broadcast Engineering
• /
• v.9 no.4 s.25
• /
• pp.424-433
• /
• 2004

Jing(gong) is one of the most well known Korean traditional Samulnori instruments to the general public. Samulnori is consisted of four instruments, them being : the jingo the janggu (hour-glass drum). the kkwaenggwari, and the buk(drum). Of the four instruments, the jing with its deep, and yet soft and beautiful long lingering sound embraces the sounds of the other three. The jing is a brassware instrument, a compound of $70{\%}\;copper\;and\;22{\%}\;tin.$\;A high quality brassware is used when the jing is made. The jing is shaped with a 39-40cm circular plate and a rim that gives 7.0-7.5cm of depth to the instrument. Even with its most simple structure, when the circular plate is hit during performance, the rim which supports the circular plate gives resonance to the sound making low-frequency sounds. Therefore the range of the representative frequency of the full rim jing is between $118.4{\~}366.0[Hz],$\;the lingering sound lasts for more than 20 seconds afterwards. When the jing with half of its rim cut off is hit the basic frequency is $139.9{\~}387.5[Hz].$\;And the sound lasted for ten more seconds. The jing of its rimless frequencies are distributed between $990.5{\~}1,372[Hz].$\;And the lingering sound lasts for 5seconds afterwards. Therefore, different thickness and depth of the rim may give new resonance frequencies and alter the longing time of the sound. This thesis paper will try to reveal the relationship between the thickness or depth of the rim (which holds the bending circular plate) and the frequency or the lasting time of the sound.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.4 s.316
• /
• pp.28-35
• /
• 2007

Airbone laser altimeters have been utilized for 3D topographic mapping of the earth, moon, and planets with high resolution and accuracy, which is a rapidly growing remote sensing technique that measures the round-trip time emitted laser pulse to determine the topography. The traveling time from the laser scanner to the Earth's surface and back is directly related to the distance of the sensor to the ground. When there are several objects within the travel path of the laser pulse, the reflected laser pluses are distorted by surface variation within the footprint, generating multiple echoes because each target transforms the emitted pulse. The shapes of the received waveforms also contain important information about surface roughness, slope and reflectivity. Waveform processing algorithms parameterize and model the return signal resulting from the interaction of the transmitted laser pulse with the surface. Each of the multiple targets within the footprint can be identified. Assuming each response is gaussian, returns are modeled as a mixture gaussian distribution. Then, the parameters of the model are estimated by LMS Method or EM algorithm However, each response actually shows the skewness in the right side with the slowly decaying tail. For the application to require more accurate analysis, the tail information is to be quantified by an approach to decompose the tail. One method to handle with this problem is proposed in this study.

• Journal of the Korean association of regional geographers
• /
• v.2 no.2
• /
• pp.49-73
• /
• 1996

This study produces quantitatively weather entropy and information ratio using information theory about frequency in the appearance of precipitation phenomenon and monthly change, and then applies them to observation of the change of their space scale by time. As a result of these, this study defines Pusan, Chongju and Kwangju's weather representativeness and then establishes the range of weather representativeness. Based on weather entropy (statistical parameter)-the amount of average weather information-and information ratio, we can define each area's weather representativeness, which can show us more constant form included topographical, geographical factors and season change. The data used for this study are the daily precipitotion and cloudiness during the recent five years($1990{\sim}1994$) at the 69 stations in Korea. It is divided into class of no precipitation, that of precipitation. The results of this study can be summarized as follows: (1) The four season's mean value of information ratio is the highest value. as 0.641, on the basis of Chongju. It is the lowest as 0.572, on the basis of Pusan. On a seasonal basis, the highest mean value of information rate is April's (spring) in Chongju, and the lowest is October's(fall) in Pusan. Accordingly weather representativeness has the highest in Chongju and the lowest in Pusan. (2) To synthesize information ratio of decaying tendancy and half-decay distance, Chonju's weather representativeness has the highest in April, July and October. And kwangju has the highest value in January and the lowest in April and July. Pusan's weather representativeness is not high, that of Pusan's October is the lowest in the year. (3) If we establish the weather representative character on the basis of Chongju-Pusan, the domain of Chongju area is larger than that of Pusan area in October, July and April in order. But Pusan's is larger than Chongju's in January. In the case of Chongju and Kwangju, the domain of Chongju area is larger than that of Kwangju in October, July and April in order, but it is less than that of Kwangju area in January. In the case of Kwangju-Pusan, the domain of Kwangju is larger than that of Pusan in October, July in order. But in April it is less than Pusan's.