• Journal of Practical Agriculture & Fisheries Research
• /
• v.25 no.1
• /
• pp.14-19
• /
• 2023

In summer, the natural ventilation performance for varying greenhouse width is very important in the glasshouses for year round cultivation. The effect of the side openings and greenhouse width on natural ventilation performance was analyzed by simulation. The necessary ventilation rate with different solar radiation transmittance increased significantly when the outside temperature grows higher. The necessary ventilation rate of 40% transmittance was about half of that of 90% transmittance. In consequence, shading effect on temperature control in greenhouse is significant in summer. When the total area of the openings for ventilation is constant, the maximum ventilation rate happens when the area of roof openings is equal to the area of side openings. This maximum ventilation rate is about 3 times of that of the greenhouse with roof openings and without side openings. Therefore, the side openings are advantageous to improve the natural ventilation in greenhouses. As the greenhouse width increases, the influence of side openings on the ventilation rate is becoming smaller. If the natural ventilation rate of the greenhouse with roof and side openings is to become double of that of the roof openings only, the width should be narrower than 38.4m for the Venlo type and 64m for Wide span type.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.21 no.2
• /
• pp.157-163
• /
• 1991

The author has evaluated the panoramic image of the maxillary sinus according to the skull position. The lead foils were attached to the five walls of the maxillary sinus and the inferior turbinate individually. The skull was located in three positions; standard position, 20㎜ forward position and chin-down position. The obtained results were as follows: 1. In standard position, the medial wall was superimposed upon most of the panoramic antral image. The anterior wall and the posterolateral wall were superimposed upon the medial half and the lateral third respectively. 2. In forward position, the width of the panoramic antral image was diminished generally. The anterior wall was superimposed upon most of the panoramic antral image and the posterolateral wall appeared narrowly at the most lateral portion of the panoramic antral image. 3. In chin-down position, there was no significant difference in comparison to the standard position. 4. Inferior turbinate was not superimposed upon the panoramic antral image.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.37-39
• /
• 2008

The purpose of this study is to improve the defects of DPP fabric by heat setting and to describe the change of physical properties of DPP fabrics. The thermosetting was carried out in autoclave from 100 to 140$^{\circ}C$ temperature range for 10min.. In this study, we investigated the effect of the thermosetting temperatures on the structural, thermal, mechanical properties and dyeability of DPP fabrics. The melting peak of multi peak changed to single peak with an increased thermosetting temperatures. The melting energy(J/g), the tensile strength and elongation were found to increase with increasing temperature of heat setting. The diffraction peak at Bragg angle(2${\theta}$) about 13.8$^{\circ}$ were very strong, and diffraction intensity, d-spacing and half-width decreased with increasing thermosetting temperatures. On the other hand, the dyeability(K/S) and crease recovery decreased with an increasing thermosetting temperatures.

• Journal of computational fluids engineering
• /
• v.15 no.2
• /
• pp.35-40
• /
• 2010

In the present work, LES with new variational multiscale method is conducted on the fully developed channel flow with Reynolds number, 180 based on the friction velocity and the channel half width. Incompressible Navier-Stokes equations are integrated using finite element method with the basis function of NURBS. To solve space-time equations, Newton's method with two stage predictor multicorrector algorithm is employed. The code is parallelized using MPI. The computational domain is a rectangular box of size $2{\pi}{\times}2{\times}4/3{\pi}$ in the streamwise, wall normal and spanwise direction. Mean velocity profiles and velocity fluctuations are compared with the data of DNS. The results agree well with those of DNS and other traditional LES.

• Structural Engineering and Mechanics
• /
• v.11 no.3
• /
• pp.259-272
• /
• 2001

The impact behavior of a multigirder concrete bridge under single and multiple moving vehicles is studied based on correlated road surface characteristics. The bridge structure is modeled as grillage beam system. A 3D nonlinear vehicle model with eleven degrees of freedom is utilized according to the HS20-44 truck design loading in the American Association of State Highway and Transportation Officials (AASHTO) specifications. A triangle correlation model is introduced to generate four classes of longitudinal road surface roughness as multi-correlated random processes along deck transverse direction. On the basis of a correlation length of approximately half the bridge width, the upper limits of impact factors obtained under confidence level of 95 percent and side-by-side three-truck loading provide probability-based evidence for the evaluation of AASHTO specifications. The analytical results indicate that a better transverse correlation among road surface roughness generally leads to slightly higher impact factors. Suggestions are made for the routine maintenance of this type of highway bridges.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.372-375
• /
• 2017

ZnO thin films were deposited by RF magnetron sputtering and then diffused by using an As source in the ampouletube. Also, the ZnO p-n homojunction was made by using As-doped ZnO thin films, and its properties were analyzed. After the As doping, the surface roughness increased, the crystal quality deteriorated, and the full width at half maximum was increased. The As-doped ZnO thin films showed typical p-type properties, and their resistivity was as low as $2.19{\times}10^{-3}{\Omega}cm$, probably because of the in-diffusion from an external As source and out-diffusion from the GaAs substrate. Also, the ZnO p-n junction displayed the typical rectification properties of a p-n junction. Therefore, the As diffusion method is effective for obtaining ZnO films with p-type properties.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1880-1885
• /
• 2016

This study aims to design a zonal lumen for parking garage LED lightings of a slim appearance and 20 W/2,000 lm capacity and to fabricate a lighting luminaire accordingly. The frame is of a one-dimensional bar type with a reverse V-shaped section, with LED chips arranged along both sides. To maximize the $60^{\circ}$ to $80^{\circ}$ zonal lumen, the geometric structure was designed with the apex of the reverse V-shaped section at $40^{\circ}$ and both sides at $70^{\circ}$. As for the LED light source, focusing lenses with narrower full-width half-maximum (FWHM) in luminous intensity were used. A ray-tracing simulation method was utilized for the zonal lumen simulation of the given structure. An actual hardware of luminaire based on the simulation results was fabricated and characterized. The suggested model is meant to develop LED lightings with a proper level of zonal lumen required in parking garages.

• Ceramist
• /
• v.10 no.3
• /
• pp.7-14
• /
• 2007

PbS QDs in glasses have attracted much attention due to the potentials for near-infrared applications. Growth of PbS QDs in the glass is discussed and size of PbS QDs formed in the glass can be tuned by varying the thermal treatment conditions. Hyperbolic-band approximation and four-band envelope function provide good simulation of the exciton energies of PbS QDs. Absorption and photoluminescence of PbS QDs was tuned into $1{\sim}2{\mu}m$ wave-length regime with large full width at half maximum photoluminescence intensity (>160 nm). Photoluminescence intensity of PbS QDs in the glasses was closely related to size of quantum dots, temperature, excitation and defects. Decrease in temperature shifted the photoluminescence bands to shorter wavelength and switched the photoluminescence from darkened state and brightened state.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.56-59
• /
• 2009

In the present work, LES with new variational multiscale method is conducted on the fully developed channel flow with Reynolds number is 180 based on the friction velocity and the channel half width. Incompressible Navier-Stokes equations are integrated using finite element method with the basis function of NURBS. To solve space-time equations, Newton's method with two stage predictor multicorretor algorithm is employed. The code is parallelized using MPI. The computational domain is a rectangular box of size $2{\pi}{\times}2{\times}4/3{\pi}$ in the streamwise, wall normal and spanwise direction. Mean velocity profiles and velocity fluctuations are compared with the data of DNS. The results agree well with those of DNS and other traditional LES.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.237-237
• /
• 2009

Zinc oxide (ZnO) thin film was deposited on Si substrates using polycrystalline (poly) 3C-SiC buffer layer, in which the ZnO film was grown by sol-gel method. Physical characteristics of the grown ZnO film was investigated experimentally by means of SEM, XRD, FT-IR (Furier Transform-Infrared spectrum), and AFM. XRD pattern was proved that the grown ZnO film on 3C-SiC layers had highly (002) orientation with low FWHM (Full width of half maxium). These results showed that ZnO thin film grown on 3C-SiC buffer layers can be used for various piezoelectric fields and M/NEMS applications.