• Journal of the Korean Electrochemical Society
• /
• v.5 no.2
• /
• pp.43-46
• /
• 2002

Commercial titanium rod was anodized in three types of electrolytes such as 0.06 mol/L $\beta-glycerophosphate+0.3mol/L$ calcium acetate, 0.06mol/L $\beta-glycerophosphate+0.3mol/L$ sodium acetate and 0.06 mol/L $\beta-glycerophosphate+5mol/L$ calcium phosphate. The titanium oxide layer $(TiO_2)$ was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and electron spectroscopy chemical analysis (ESCA). Numerous micropores were observed on the titanium oxide layer by SEM. The diameter of micropores increased with the increase of electrolytic voltage. The titanium oxide layer was composed of anatase structure. The phosphorous element was detected at 130 eV binding energy, but calcium was not found in the oxide layer because of lower contents. After anodizing the oxide layer was etched in the 30g/L NaOH solution at $80^{\circ}C$ for 1hr. The surroundings of micropores were much more smoothed and rounded than before alkaline etching.

• Journal of Welding and Joining
• /
• v.17 no.4
• /
• pp.53-59
• /
• 1999

Amorphous alloys have also been called glassy alloys or non-crystalline alloys. They are made by the rapid solidification. The solidification occurs so rapid that the atoms are frozen in their liquid configuration. There are unique magnetic, mechanical, electrical and corrosive behaviors which result form their amorphous structure. In the study. amorphous coatings were manufactured with Ni-Cr-B-Si powders by flame spray. Measurement of hardness, were resistance, corrosion resistance and observation of microstructures and XRD, DSC were performed to investigate characteristics of amorphous coatings. The experimental results obtained as follow: 1) Amorphous powders could not be manufactured with the spraying in the spraying in the liquid nitrogen. But, amorphous coatings could be manufactured with the rotation cooling method by liquid nitrogen. In the fabrication of amorphous coatings, major factor was the rapid cooling by rotation of the substrate. 2) Hardness of coatings was obtained Hv 960 by formation of amorphous phase. But, wear resistance decreased. That was due to porosity in the coatings by the rapid cooling. 3) In the case of corrosion resistance, amorphous coatings were superior to air-cooled coatings. That was due to formation of amorphous phase. 4) After amorphous coatings were heat-treated at 520℃ for 1hr. hardness increased 80% and wear resistance increased 30% comparing with air cooled coatings. These were due to crystallization of amorphous phase and decrease of porosity by heat-treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.251-251
• /
• 2011

본 연구에서는 Zr이 도핑 된 ZnSnO (ZZTO) 기반의 물질을 액상공정을 이용하여 합성하고, 박막트랜지스터를 제작하였다. 출발 물질로써 지르코늄 클로라이드 (ZrCl4), 아연 아세테이트 디하이드레이트 ($Zn(CH_3COO)_2{\cdot}2H_3O$), 틴 클로라이드 ($SnCl_2$)를 아연과 주석 프리커서의 비율을 4:7로 고정하고, 지르코늄 프리커서의 몰비를 변형시켜 제작하였다. 제작된 솔루션은 0.25몰의 몰 농도로 고정하였다. 솔벤트로는 2-메톡시에탄올 (2-methoxyethanol)을 사용하였으며, 준비된 솔루션은 $0.2{\mu}m$ 필터를 이용하여 필터링을 실시하였다. Heavily doped p+ Si 기판에 열적 산화법을 이용하여 120 nm 두께의 $SiO_2$를 성장시킨 것을 게이트 및 게이트 절연막으로 이용하였으며, 스핀코팅을 이용하여 ZZTO 박막을 코팅하였다. 코팅 된 기판은 $300^{\circ}C$에서 $500^{\circ}C$ 사이로 2시간 열처리를 실시하였으며, 마지막으로 소오스/드레인을 스퍼터링법으로 Al을 증착하였다. Zr 함량비, 열처리 온도, 제작된 솔루션의 온도에 따른 박막단계를 파악하기 위해 X-ray photoelectron spectroscopy (XPS), thermogravimetry differential thermal analyzer (TG-DTA), X-ray diffractometer (XRD), high-resolution transmission electron microscopy (HR-TEM), Hall-effect measurement, UV-Vis spectroscopy 분석을 실시하였으며, 제작된 소자는 semiconductor analyzer (HP4156C)를 이용하여 측정하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.327-331
• /
• 2011

Zinc oxide (5, 10 and 15 wt%) impregnated NaZSM-5 zeolite synthesized using rice husk ash as silica source was tested for $CO_2$ adsorption. The materials were characterized by XRD, SEM-EDS, $CO_2$-TPD and BET techniques. The heat of the reaction (${\Delta}$Hr) derived from DSC for ZnO(10%)/NaZSM-5 was found to be 495 Btu/lb and the maximum $CO_2$ adsorption capacity of ZnO(10%)/NaZSM-5 is 140 mg/g of sorbent. Extraction of silica from the agricultural waste, rice husk and its use in the zeolite synthesis is an added advantage in this study. Hence, from the study it is concluded that zinc oxide impregnated NaZSM-5 could be treated as novel material for $CO_2$ adsorption as they were found to be regenerable, selective and recyclable.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1490-1492
• /
• 1994

Diamond thin films were deposited on Si substrate from $CH_4-H_2-O_2$ system by MWPECVD at the condition of power of 800W, pressure of 80torr, $H_2$ flow rate of $75{\sim}81sccm$, $O_2$ flow rate of $0{\sim}3.8sccm$, $CH_4$ flow rate of $4.8{\sim}9sccm$, substrate temp, of $950{\sim}1010^{\circ}C$ and deposition time of 5hr. The deposited films were characterized by SEM, XRD and Raman spectroscopy. The growth rates of thin films and particles was measured. Good quality were synthesized at 40% of oxygen concentration which 6% of fixed metane concentration, and at 50%. Its deposition rates were $2.4{\mu}m/h$ respectively. As oxygen concentration increased, it was known that the broad peak of $1350 cm^{-1}$ was shifted to $1332cm^{-1}$ due to etching of carbon component.

• Journal of Powder Materials
• /
• v.25 no.1
• /
• pp.48-53
• /
• 2018

One-dimensional rutile $TiO_2$ is an important inorganic compound with applicability in sensors, solar cells, and Li-based batteries. However, conventional synthesis methods for $TiO_2$ nanowires are complicated and entail risks of environmental contamination. In this work, we report the growth of $TiO_2$ nanowires on a Ti alloy powder (Ti-6wt%Al-4wt%V, Ti64) using simple thermal oxidation under a limited supply of $O_2$. The optimum condition for $TiO_2$ nanowire synthesis is studied for variables including temperature, time, and pressure. $TiO_2$ nanowires of ${\sim}5{\mu}m$ in length and 100 nm in thickness are richly synthesized under the optimum condition with single-crystalline rutile phases. The formation of $TiO_2$ nanowires is greatly influenced by synthesis temperature and pressure. The synthesized $TiO_2$ nanowires are characterized using field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HR-TEM).

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.8
• /
• pp.335-339
• /
• 2002

Ba(Mgl-xCox)TaO3[BMCT] ceramics were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of 1525~$1625^{\circ}C$ for 5hr. in air. The crystal structure of BMCT ceramics was investigated by the XRD. The microstructure of the specimens were observed by SEM. The Microwave dielectric properties of BMCT specimens were investigated as a function of composition and sintering temperature. All BMCT ceramics sintered over 1575$^{\circ}C$ were showed a polycrystalline complex perovskite structure. The density of BMCT (90/10) specimen sintered at $1575^{\circ}C$ was 7.75g/㎤. As the Co contents decreased, the ordering parameter of B-site in BMCT increased. In the case of the BMCT(90/10) ceramics sintered at $1575^{\circ}C$ for 5 hours, dielectric constant, quality factor and temperature coefficient of resonant frequency for microwave dielectrics application were a good value o( 25, 17, 845 at 10㎓ and +2.4 ppm/${\circ}$, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.481-484
• /
• 1999

The undoped-InSe and Sn-doped InSe single crystals were grown by vertical Bridgman method and their properties were invesigated. These crystals were obtained by lowering the quartz ampoule for growth in the furnace and growth rate at optimum condition is 0.4mm/hr. The orientations and the crystallinites of these crystals were identified by X-ray diffraction(XRD), double crystal rocking curve(DCRC) and etch-pit density(EPD) measurements. From the Raman spectrum at room temperature, TO, LO modes together with their overtones and combinations were observed. Optical properties were investigated by photoluminescence at 12K and direct band gap of these crystals obtained from optical absorption spectrum. Compared with undoped-lnSe, electrical properties of Sn-doped InSe were increased and the electrical conductivity type were n-type. But electrical properties along growth direction of crystals and radial direction of wafer showed nearly uniform distribution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.3
• /
• pp.141-145
• /
• 2014

Tubular-shaped ZnO crystals were synthesized by thermal evaporation technique under air atmosphere. Mixture of Zn and Mg powder was used as the source material. The thermal evaporation and oxidation of Zn/Mg mixture were carried out for 1 hr at $1,000^{\circ}C$ and $1,200^{\circ}C$ under in air under atmospheric pressure. When only Zn powder was used as a source material, tetrapod-shaped ZnO crystals were synthesized. This provides that Mg played a key role in the formation of the tubular-shaped crystals. SEM images showed that the tubular-shaped ZnO crystals grew along [0001] direction. XRD spectrum revealed that the ZnO tubes had hexagonal wurtzite structure. Two emission peaks at 380 nm and 510 nm were observed in the room temperature cathodoluminescence spectrum.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.910-914
• /
• 2010

A novel synthetic route has been developed to prepare $\alpha$-cobalt hydroxide with intercalated nitrate anions. It was successfully synthesized by $\gamma$-ray irradiation under simple conditions, i.e., air atmosphere, without base. Under $\gamma$-ray irradiation, it leads to the formation of layered cobalt hydroxynitrate compounds which have small crystalline size and have the role of a generator of hydroxyl anion. Structural and morphological characterizations were performed by using power X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and high resolution transmission electron microscopy (HR-TEM). The component and thermal stability of the sample were respectively measured by Fourier transform infrared (FT-IR) spectroscopy, elemental analysis, and thermal analyses, including thermogravimetry (TG) and differential thermal analysis (DTA).