• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.04a
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• Journal of Nutrition and Health
• /
• v.41 no.6
• /
• pp.530-538
• /
• 2008

This study was performed to assess the effects of beverage consumption on nutrient intake and anthropometric measurements. Beverage intake and dietary intake were measured by a beverage frequency and quantity questionnaire and three 24-hour dietary recalls in 160 elementary school students in the Gyeongnam area. The number of drinking moments per month was 93.5 and drinking amount of all beverages was 626.6 mL per day. The amount of milk intake was 253.8 ml per day, which was the highest in all types of beverage consumption, followed by juice(133.6 mL), and carbonated beverage(77.7 mL). The amount of sweetened beverage which was defined as all beverages except milk and soy milk was 359.7 mL per day. Energy intakes from all kinds of beverages and sweetened beverages accounted for 20.3% and for 10.5% of the daily energy intake, respectively. The contributions of sweetened beverage intake to the daily energy intake in girls accounted for 13.5%, whereas in boys it was 7.7% and significantly lower. The number of drinking moments and the contribution of sweetened beverage intake to daily energy intake were negatively correlated with protein, vitamin A and niacin intake, respectively. The consumption of milk and soybean milk combined showed a significant negative correlation with the body fat ratio(%) and it also negatively correlated with waist-hip girth ratio(WHR). However, the sweetened beverage intake was not related any of the anthropometric measurement. In conclusion, consumption of the sweetened beverage dropped the nutritional quality of diet. However it was not related with anthropometric measurements in elementary students.

• Journal of Nutrition and Health
• /
• v.41 no.3
• /
• pp.254-263
• /
• 2008

This study was conducted to analyze the effect of isoflavone intake on prevention of chronic disease in middle and old aged man. In this study we used FFQ (Food frequency questionnaire) and the isoflavone intake level of the subjects was 25.10 mg per day. We divided the subjects into three group -high, medium, low isoflavone intake level- and investigated the relation among isoflavone intake level and clinical/anthropometric characteristics. The intake of isoflavone was inversely related with the body fat in male subjects. And we also divided the subjects into 2 groups with normal and abnormal clinical/anthropometric risk factor. The isoflavone intake level of the abnormal group with high TG, high WHR and high body fat was lower than the normal group. The main food source of isoflavone was soybean curd, bean sprout, soybean paste, soybean and soy milk, and we also investigated the relation between frequency of soybean food and anthropometric and clinical variables. The frequencies of soybean curd, soybean paste, soybean broth, soy milk, bean sprouts, peanuts, soybean and dambuk as well as intake of isoflavone were inversely correlated with some anthropometric and clinical variables such as blood pressure, TG, BMI, % body fat, and waist-hip ratio, whereas positively correlated with HDL cholesterol, muscle mass and bone density. We suggest that high consumption of soy products and isoflavone is associated with decreased blood lipid and body fat in middle and old aged man and might be useful for prevention cardiovascular diseases. From this study, we obtained valuable basic information on recommended isoflavone intake level and guidelines for the prevention of some chronic diseases/health problems.

• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.157-163
• /
• 2004

Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$＋/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.

• The Korean Journal of Nuclear Medicine
• /
• v.28 no.2
• /
• pp.206-213
• /
• 1994

We studied 90 patients(179 femoral heads) with avascular necrosis of femoral head, who had been performed X-ray, bone scan and MRI to compare of the findings of AVN on bone scan between each other, retrospectively. The patients were 82 males and 9 females, their mean age was 45 years. Radiographic stages were classified by Steinberg modification, radionuclide stages were classified as followed; stage o(or type 0) : normal, stage 1 : faint ring like uptake around the femoral head, stage 2: intense ring like uptake, stage 3: irregular increased uptake with central photon defect, stage 4 : Intense diffuse increased uptake at femoral head and stage 5 : hip joint deformity with relatively mild increased uptake. The findings of MRI were classified according to extent, location, early or advanced lesion, signal intensity of the lesion and joint effusion. 156(87%) of 179 femoral heads had avascular necrosis, 68(75.5%) of 90 patients had bilateral AVN, 35 femoral heads had early stage and 120 had advanced stage. The detection rate of AVN by X-ray and bone scan were 85% (134), 91.6% (143), respectively. Early AVN with atypical types of bone scan showed larger extent, moderate to large amount of joint effusion, soft tissue hypertrophy within joint, and secondary degenerative changes. Bone scan had relatively high detection rate in the diagnosis of AVN of femoral head, and demonstrated various types depending on the disease stage.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.3-9
• /
• 2011

Purpose: Generally dual energy X-ray absorptiometry has been used for the purpose of evaluation of osteoporosis and treatment. Recently the interest of obesity came to be high and body percent fat test is increasing. Existing measure of body fat have to scan the whole body can be evaluated, but only lumbar spine and hip measurements was assumed to be whole body fat as well as improving the software. It tries to check whether the part measured value not being whole body measurement has the validity or not compared with the value calculated with the method that it is different, it forgives through a correlation with a (BIA) and (BMI). Materials and Methods: In 2010, the body percent fat was measured among the examinee coming to the Asan Medical Center public health care center from March till August against 90 females more than 40 years old through (DXA) and BIA. BMI utilized the value which wrote an hight and weight measured through the body measuring instrument in the examinee information and is automatically calculated. In addition, it classified as the low weight ($13-18.5kg/m^2$), normal ($18.5-25kg/m^2$), and corpulence ($25-30kg/m^2$) based on BMI and so that it could check whether there was the difference according to the weight or not BMI and BIA and correlation between DXA were analyzed in each group. The statistical program for the analysis used SPSS 12.0. Results: The comparison of DXA at 3 which it divides into the low weight and normal and corpulence groups and BIA did not show the difference noted statistically in all groups and the between group comparison was exposed to do not have a meaning. The body percent fat measured by the correlation analysis result DXA at the state that it doesn't divide into the group showed the high correlation (r=0.908, p0.01) noted statistically compared with BMI and showed the high correlation noted statistically in a comparison with BIA (r=0.927, p0.01). Conclusion: It confirmed that the whole body percent fat presumed from the part bone density measurement showed the excel correlation compared with BIA and BMI and information is high. There is still no clear standard about the presumed whole body percent fat and it is difficult to evaluate the fat evaluation by the bone mineral density measurement. However, it is determined that the information offering which is more objective through the comparative study with the body percent fat which is very efficient and in that it can obtain till the information about a fat as well as diagnosis of the osteoporosis through the bone density checkup is measured by the afterward telegraph bone density checkup and is clinically useful is possible.

• The Korean Journal of Nuclear Medicine
• /
• v.29 no.1
• /
• pp.84-91
• /
• 1995

Many clinical and laboratory tests have been employed to evaluate disease activity in rheumatioid arthritis. $^{99m}Tc$-labelled polyclonal IgG(HIG) has been demonstrated to accumulate in focal sites of infection or inflammation in both animals and human subjects. The purpose of this study was to distinguish arthritis with active inflammation from those without active inflammation and to correlate relative intensities of $^{99m}Tc$-labelled HIG uptake of the rheumatoid arthritis with clinical and MR indices of the joint inflammation. This study included twelve patients with active rheumatoid arthritis, two with ankylosing spondylitis and one with degenerative osteoarthritis without active inflammation. A Whole-body and spot images were obtained 4 hours after intravenous injection of 20mCi of $^{99m}Tc$-labelled HIG. Scintigrams were assessed visually by 3 experienced radiologists, and graded as normal or mildly and markedly increased uptake within the joints, and the degree of uptake was compared with clinical and radiologic severity of synovial inflammation. MRI studies were done on the involved joints consisted of wrist(n = 11), knee(n = 2) and hip joint(n= 2). Active synovitis was defined when marked elevation of ESR and gadolinium enhancement of synovium on MRI were demonstrated. Markedly increased radiotracer uptake was seen in 10 of 11 rheumatoid arthritic patients with active synovitis whereas normal or mildly increased uptakes were noted in others, including rheumatoid arthritic patient(n=1) and non-rheumatoid patients(n = 3) without active synovitis. This study showed that the localization of involved joints in rheumatoid arthritis could be detected with $^{99m}Tc$-labelled HIG and that the degree of uptake correlated well with the degree and activity of inflammation. In conclusion, $^{99m}Tc$-labelled HIG scan is a useful method in the evaluation of active inflammation in rheumatoid arthritis.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.17 no.4
• /
• pp.622-637
• /
• 1993

The Purposes of this study were to investigate the significant correlation among the length changes of body surface total lines and between the length changes of body surface total lines and those of component body surface segment lines, and to reveal anticipated relation among body surface length changes by the lower limb movement including all movement direction of hip joint, knee joint & ankle joint for the more functional clothing making & designing. 10 Crosswise & 5 lengthwise body surface total lines and 48 crosswise & 39 lengthwise body surface segment lines of 26 female college students aged from 18 to 24 years were measured directly on the body surface and analyzed by ANOYA & Multiple Comparison Test(Tukey), and the length changes of them were calculated as the difference of the mean length at Fl movement from the mean length at each movement and were analyzed by PEARSON CORRELATION. The results were as following : 1. Correlation among the length changes of body surface total lines (1) Correlation among the length changes of body surface total lines significantly changed by the movement ; 1) The more GA5 expanded, the more GA6 & GA7 each expanded, and the more GA18 expanded, the more GA1 & GA3 each expanded. 2) The more GA15 expanded, the less GA14 each contracted. 3) The more GA7 expanded, the larger GA17 contracted. 4) The more GA1 & GA18 expanded, the larger GA16 contracted, and the larger GM contracted, the less GA16 contracted. (2) Only GA7 and GA17(at F4) showed high (over r=0.7) correlation coefficient, But others' correlation coefficients were r=0.4~0.7. (3) Correlation coefficients among & between girth items and length items 1) Correlation coefficients among girth items were shown + ; between GA3 and GA4, GA5, GA8, between GA5 and GA6, GA7, GA9 each, between GA1 and GA6 and between GA4 and GA7. 2) Correlation coefficients among length items were shown + or - ; shown + between GA14 and GA15 and between GA17 and GA16 ; but Shown - Between GAlS and GA16. 3) Correlation coefficients between girth items and length items were mainly shown - : shown-between GA1 and GA16, GA17, between, GA4 and GA16, between GA6, GA7 each and GA17, between GA8 and GA18 ; but shown + between GA1, GA3 each and GA18 and between GA8 and GA14 were shown +. 2. Correlation between the length changes of body surface total lines and those of component body surface segment lines. (1) All correlation coefficients were + except A147 of GA14. (2) Correlation coefficient over r=0.7 was shown ; between GA3 and CB3, A35 each, between GA5 and A054, between GA6 and A63, between GA7 and A72, A74 each, between GA8 and A83, A84 each, between GA15 and A153, between GA16 and Al64, Al65 each, between GA18 and A189 : but was not shown between GA4, GA17 and it's component body surface segment lines each. (3) Characteristics of correlation between the length changes of body surface total lines and those of body surface segment lines ; 1) If significant correlation of body surface total lines were expansion parts, it's component body surface segment lines was also expansion segment and the otherwise were the same. But exception was shown between expansion line GA3 and A031 (at F4), between GA18 and AlS9 (at F6) and between GA14 and A147, so to speak GA3 & lines and GA14 was contraction total line oppositely A147 was expansion. 2) The more GA3, GAlS expanded, the less A031, A189 contracted. 3) The more GA14 contracted, the more A147 expanded. 4) All correlation except the above 2), 3), the more total lines (GA1, GA3, GA5, GA15, GA16, GA18) expanded, the more segment lines (A15, CB1, A31, A34, CB3, A52, A54, A153, A169, A181) expanded, or the larger total lines (GA14, GA16, GA17) contracted, the larger segment lines (A141, A142, A161, A164, A165, A172) contracted.

• Journal of Nutrition and Health
• /
• v.41 no.8
• /
• pp.742-753
• /
• 2008

The purpose of this study is to investigate risk factors of pre-hypertension and hypertension in rural residents. Nine hundred and ninety four subjects aged 40-70 yrs in Chungnam-do participated in this study. The subjects (n = 824) were classified into three groups of hypertensive, pre-hypertensive, and normotensive according to the Joint National Committee (JNC)-7 criteria. The weight, body mass index (BMI), waist-hip ratio (WHR), and serum total protein, albumin, BUN, and triglyceride (TG) were positively correlated with SBP and DBP. After adjusted by age, sex and BMI, the total protein, albumin and TG were significantly correlated with SBP and DBP (p < 0.01). There was no significant difference in eating habits according to the level of blood pressure. The serum albumin, creatinine, Glu-FBS, Glu-PP l20, and triglyceride were higher in both prehypertensive and hypertensive group than in the normotensive group. However, mean serum cholesterol was not different among three blood pressure groups. In this study, the common risk factors of pre-hypertension and hyper-tension were male, age of fifties, lower education level, ex-smoking, higher drinking frequency, higher BMI, body fat %, waist circumference, WHR, serum albumin and diabetes, even though the degree of risks in these variables were higher in the hypertensive group. The higher BUN was a risk factor of prehypertension, while the family history, prediabetes, serum total protein, Glu-PP l20 and higher alcohol drinking amount were the risk factors of hypertension. This result suggests that maintaining good health habit and normal range of blood parameters as well as controlling body weight have to be paid attention in order to prevent hypertention, and further reseasch on the relationship of blood pressure and BUN are needed.

• Journal of dental hygiene science
• /
• v.15 no.2
• /
• pp.119-128
• /
• 2015

The purpose of this study is to understand the effects of obesity and stress on oral disease in Korean adults by using the data of the Fifth Korea National Health and Nutrition Examination Survey. The subjects of this study are 4,627 adults at the age of 19 to 64, and the data were analyzed by using SPSS Windows ver.18.0. The results are as follows: Obesity was higher in men and the age of 40 to 64 than the other. And the group with lower education or lower income level tended to show significantly higher obesity (p<0.05). As for stress, women, the age of 19 to 39 and the subjects with higher academic career tended to indicate significantly higher stress (p<0.05). As for the effects of obesity on oral disease, there were no significant difference between body mass index (BMI) or waist-hip ratio (WHR) and oral disease but there was statistically significant difference between stress and temporomandibular joint disorder (TMD) (p<0.05). Even when the subjects with stress were obese or abdominally obese, there was no significant difference in oral disease (p>0.05). As to correlation among variables, there were correlations between BMI and WHR, stress and TMD, masticatory problems and periodontal disease or TMD (p<0.05). About the effects of general characteristics, obesity, and stress on oral disease, age was the variable influencing TMD, and age and abdominal obesity were the variables influencing masticatory problems (p<0.05). In this society, the environment surrounding individuals is fairly complex, and the concept of health including quality of life has more complex meaning than in the past. Various factors are influencing obesity and stress, and they are also influencing oral health and behaviors. Accordingly, it will be needed not only to make efforts to reduce obesity and stress but also to employ approaches from different perspectives to improve oral health.