• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.2
• /
• pp.70-78
• /
• 2012

Due to the variable nature of renewable energy resources and power demand by consumers, it is difficult to operate a power system installed with only one type of renewable energy resource. Grid-based renewable generation may be the only solution to overcome this problem. The conventional approach based on a low-voltage converter with power frequency transformer is commonly employed for grid connection of offshore renewable energy systems. Because of the heavy weight and large size of the transformer, the system can be expensive and complex in terms of installation and maintenance. In this paper, an 11-kV series connected H-bridge (SCHB) multilevel voltage source converter (VSC) is proposed to achieve a compact and light direct grid connection of renewable energy systems. This paper presents the design, simulation and analysis of a five level (5L)-SCHB and an eleven level (11L)-SCHB VSC for 11-kV grid-based renewable energy systems. The performance, cost, modulation scheme and harmonic spectra of the converter are analyzed.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2668-2670
• /
• 1999

In the past, the PWM converter had a large switching loss by hard switching and difficult to high frequency operation. The resonance converter to decrease the switching loss and EMI is required the frequency control and needed to reduce the voltage or current stress at each parts. So, this paper propose the 3-phase boost converter and the method to compensated input power factor by control the amplitude - an instantaneous value of the DC inductor current -and control the switching frequency that a modulation error by the ripple of the DC inductor current. The proposed 3-phase PWM boost converter of single phase control type can takes higher capacity and compensate the power factor by using Feed back controller at each phase for the existing 3-phase bridge rectifier type. Moreover the 3-phase full bridge type using the rectifier at each 3-phase circuit will be small size reactor and compensate input power factor by minimize harmonic components of each phase.

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1186-1194
• /
• 2017

This paper proposes an improved low frequency Selective Harmonic Mitigation-PWM (SHM-PWM) technique. The proposed method mitigates the low order harmonics of the output voltage up to the $50^{th}$ harmonic well and satisfies the grid codes EN 50160 and CIGRE-WG 36-05. Using a modified criterion for the switching angles, the range of the modulation index for non-linear SHM equations is improved, without increasing the switching frequency of the CHB converter. Due to the low switching frequency of the CHB converter, mitigating the harmonics of the converter up to the $50^{th}$ order and finding a wider modulation index range, the size and cost of the passive filters can be significantly reduced with the proposed technique. Therefore, the proposed technique is more efficient than the conventional SHM-PWM. To verify the effectiveness of the proposed method, a 7-level Cascaded H-bridge (CHB) converter is utilized for the study. Simulation and experimental results confirm the validity of the above claims.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.2
• /
• pp.216-225
• /
• 2006

This paper presents a new circuit topology of DC busline switch and snubbing capacitor-assisted full-bridge soft-switching PWM inverter type DC-DC power converter with a high frequency link for low voltage large current applications as DC feeding systems, telecommunication power plants, automotive DC bus converters, plasma generator, electro plating plants, fuel cell interfaced power conditioner and arc welding power supplies. The proposed power converter circuit is based upon a voltage source-fed H type full-bridge high frequency PWM inverter with a high frequency transformer link. The conventional type high frequency inverter circuit is modified by adding a single power semiconductor switching device in series with DC rail and snubbing lossless capacitor in parallel with the inverter bridge legs. All the active power switches in the full-bridge inverter arms and DC busline can achieve ZVS/ZVT turn-off and ZCS turn-on commutation operation. Therefore, the total switching losses at turn-off and turn-on switching transitions of these power semiconductor devices can be reduced even in the high switching frequency bands ranging from 20 kHz to 100 kHz. The switching frequency of this DC-DC power converter using IGBT power modules is selected to be 60 kHz. It is proved experimentally by the power loss analysis that the more the switching frequency increases, the more the proposed DC-DC converter can achieve high performance, lighter in weight, lower power losses and miniaturization in size as compared to the conventional hard switching one. The principle of operation, operation modes, practical and inherent effectiveness of this novel DC-DC power converter topology is proved for a low voltage and large current DC-DC power supplies of arc welder applications in industry.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.687-693
• /
• 1998

An improved zero voltage and zero current switching (ZVZCS) full bridge (FB) PWM converter is proposed to solve the problems of the previously presented ZVACS-FB-PWM converter with secondary active clamp such as narrow ZVS range of leading-leg switches [6]. By adding an auxiliary inductor in between the leading-leg and separated input source voltages, the ZVS of leading leg switches can be extended to the whole line and load ranges, which eliminates unwanted hard switching of clamp switch and simplifies its control. The principle of operation is explained and analyzed. The features and design considerations of the proposed converter are also illustrated and verified on a 3 kW, 100 KHz IGBT based experimental circuit.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.203-204
• /
• 2018

Conventional buck-boost converter has the disadvantage that the output voltage is inverted. The single phase non-inverting buck-boost converter(SPNIBBC) used four swithes has H-bridge type Circuit. The output voltage is not inverted. The SPNIBBC can be controlled by the single carrier method and the dual carrier method according to the modulation method. In this paper, we have fabricated the converter and compared the efficiency according to the modulation method.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.121-122
• /
• 2014

멀티 레벨 인버터는 높은 출력 전압을 갖으며, 낮은 THD(Total harmonic distortion)를 요구하는 시스템에 적합하다. 그 중 cascaded H-brige 멀티레벨 인버터는 H-bridge 셀별 관리가 쉽고, 레벨 수를 증가시키기 쉽다는 장점 때문에 많이 이용되어 왔다. 본 논문에서는 cascaded H-bridge 인버터의 기존 PI (proportional integral) 제어 기반 PWM (pulse width modulation)기법의 스위칭 패턴과 모델 예측 제어의 스위칭 패턴을 비교하고 모델예측 제어 시 셀 별 스위칭 패턴 균형을 위한 방법을 제안한다.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.218-219
• /
• 2016

This paper present Phase Shifted with carrier based on Sinusoidal PWM(SPWM) by using Cascaded NPC/H-birdge converter. The proposed Phase Shifted PWM method is adding third harmonic injection in switching signal. The advantage of the proposed method is reducing the voltage and capacity of the capacitor. This paper compare general Phase Shifted method with proposed Phase Shifted method that added the third harmonic injection. Each PWM method is tested without considering the switching loss by using PSIM 9.1.4 simulation.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.351-354
• /
• 1996

A zero-voltage-transition(ZVT) full bridge (FB) boost converter for single stage power factor correction (PFC) in distributed power system is proposed. A simple auxiliary circuit provides zero-voltage-switching(ZVS) condition to all semiconductor devices without imposing additional voltage and current stresses and loss of PWM capability. The proposed boost converter provides both input power factor correction and direct conversion from $110{\sim}220VAC$ line to 300VDC bus with single power stage. Operational principle, analysis of the proposed converter are described and verified by computer simulation and experimental results from a 1.5 kW, 80 kHz laboratory prototype.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.323-324
• /
• 2015

Recently, asymmetrical cascaded H-bridge multilevel inverter started to be highlighted as an alternative for the symmetrical cascaded H-bridge. The topology has a small number of part count compared to the symmetrical with higher number of levels. However, it has a drawback of the modulation index limitation which is relatively higher than its symmetrical counterpart, which causes a necessity of an extra voltage pre-regulator. In this paper, the single-sourced pre-regulator is unified with an inner single switch DC/DC converter isolated by coupled inductor. It leads to cost and size reduction. The proposed topology is verified using simulation results.