• 제목/요약/키워드: Gun Gas

검색결과 453건 처리시간 0.027초

DC 마그네트론 스퍼터링을 이용한 IZO 박막의 제조와 특성 연구 (Preparation and Characterization of IZO Thin Films grown by DC Magnetron Sputtering)

  • 박창하;이학준;김현범;김동호;이건환
    • 한국표면공학회지
    • /
    • 제38권5호
    • /
    • pp.188-192
    • /
    • 2005
  • Indium zinc oxide (IZO) thin films were deposited on glass substrate by dc magnetron sputtering. The effects of oxygen flow rate and deposition temperature on electrical and optical properties of the films were investigated. With addition of small amount of oxygen gas, the characteristic properties of amorphous IZO films were improved and the specific resistivity was about $4.8{\times}10^{-4}\Omega{\cdot}cm$. Change of structural properties according to the deposition temperature was observed with XRD, SEM, and AFM. Films deposited above $300^{\circ}C$ were found to be polycrystalline. Surface roughness of the films was increased due to the formation of grains on the surface. Electrical conductivity became deteriorated for polycrystalline IZO films. Consequently, high quality IZO films could be prepared by do sputtering with $O_{2}/Ar{\simeq}0.03$ and deposition temperature in range of $150\~200^{\circ}C$; a specific resistivity of $3.4{\times}10^{-4}{\Omega}{\cdot}cm$, an optical transmission over $90\%$ at wavelength of 550 nm, and a rms value of surface roughness about $3{\AA}$.

DC magnetron sputtering법으로 제조된 Ti-Si-N코팅막의 내산화성에 관한 연구 (High-temperature oxidation resistance of Ti-Si-N coating layers prepared by DC magnetron sputtering method)

  • 최준보;류정민;조건;김광호;이미혜
    • 한국표면공학회지
    • /
    • 제35권6호
    • /
    • pp.415-421
    • /
    • 2002
  • Ti-Si-N coating layers were codeposited on silicon wafer substrates by a DC reactive magnetron sputtering technique using separate titanium and silicon targets in $N_2$/Ar gas mixtures. The oxidation behavior of Ti-Si-N coating layers containing 4.0 at.%, 10.0 at.%, and 27.3 at.% Si was investigated at temperatures ranging from 600 to $960^{\circ}C$. The coating layers containing 4.0 at.% Si became fast oxidized from $600^{\circ}C$ while the coating layers containing 10.0 at.% Si had oxidation resistance up to $800^{\circ}C$. It was concluded that an increase in Si content to a level of 10.0 at.% led to the formation of finer TiN grains and a uniformly distributed amorphous Si3N4 phase along grain boundaries, which acted as efficient diffusion barriers against oxidation. However, the coating layers containing 27.3 at.% Si showed relatively low oxidation resistance compared with those containing 10.0 at.% Si. This phenomenon would be explained by the existence of free Si which was not nitrified in the coating layers containing 27.3 at.% Si.

Assessment of N2O Emission Factor of Autumn Chinese Cabbage Fields at Three Different Geographical Location in South Korea

  • Kim, Gun-Yeob;Park, Woo-Kyun;Jeong, Hyun-Cheol;Lee, Sun-il;Kim, Pil-Joo;Seo, Young-Ho;Na, Un-sung
    • 한국토양비료학회지
    • /
    • 제48권3호
    • /
    • pp.163-169
    • /
    • 2015
  • The level of nitrous oxide ($N_2O$), a long-lived greenhouse gas, in atmosphere has increased mainly due to anthropogenic sources, especially application of nitrogen fertilizers. Quantifying $N_2O$ emission in the agricultural field is essential to develop national inventories of greenhouse gases (GHGs) emission. The objective of this study was to develop an emission factor to estimate the direct $N_2O$ emission from an agricultural field cultivated with the Chinese cabbage during autumn season in 2010-2012. Emission factor of $N_2O$ calculated over three years experiment using accumulated $N_2O$ emission, nitrogen fertilization rate, and background $N_2O$ emission was $0.0058{\pm}0.00254kg\;N_2O-N\;kg^{-1}\;N$. More extensive studies need to be conducted to develop $N_2O$ emission factors for other upland crops in the various regions of Korea because $N_2O$ emission is influenced by many factors including climate characteristics, soil properties, and agricultural practices as well as crop species.

이온빔보조증착법으로 합성한 hexagonal BN막의 hexagonal ring의 배열과 결정성 (Alignment and lattice quality of hexagonal rings of hexagonal BN films synthesized by ion beam assisted deposition)

  • 박영준;한준희;이정용;백영준
    • 한국진공학회지
    • /
    • 제8권1호
    • /
    • pp.43-50
    • /
    • 1999
  • 이온빔보조증착법으로 h-BN을 증착하여 이온에너지 및 기판온도에 따른 hexagonal ring의 배열 및 결정성의 변화를 연구하였다. 보론은 전자빔으로 1.5 $\AA$/sec 의 속도로 증발시켰으며, 질소는 둥-hall 형 이온건으로 60, 80, 100eV의 에너지로 공급하였다. 기판의 온도는 상온(no heating), 200, 400, 500, $800^{\circ}C$로 변화시켰다. 질소이온에너지가 증가할수록 hexagonal ring의 c축은 기판에 평행하게 배열하여 100 eV의 질소이온에너지에서 가장 좋은 배열을 나타내었다. 이는 이온에너지가 높을수록 합성 막에 큰 압축응력이 발생하기 때문으로 생각된다. 기판온도에 따라서는 온도가 증가함에 따라 배열이 증가하다가 약 $400^{\circ}C$에서 최대가 되고 그 보다 높은 온도에서는 배열이 감소하였다. 그리고 결정도는 온도가 증가할수록 향상되었다. 이러한 경향들은 온도가 증가함에 따라 원자 이동도는 증가하고 응력발생은 어려워지는 경향으로부터 잘 설명된다. 또한 nano-indentor로 측정한 h-BN막의 경도는 c-축의 배열정도와 같은 경향을 보였다. 이온빔보조증착법은 hexagonal ring의 배열을 통해 h-BN막 성질의 최적화에 효과적인 방법으로 판단된다.

  • PDF

용융탄산염에 대한 스테인레스강의 내식성 향상을 위한 NiAl 피복에 관한 연구 (Study on the NiAl Coating for Corrosion Resistance of Stainless Steel in Molten Carbonate Salt)

  • 황응림;강성군
    • 한국재료학회지
    • /
    • 제7권1호
    • /
    • pp.76-80
    • /
    • 1997
  • 용융탄산염 연료전지 분리판의 wet-seal부의 내식성 향상을 위한 NiAl 피복공정이 조사되었다. AlSl 316 스테인레스강위에 Ni과 Al를 순차적으로 피복한 후, $800^{\circ}C$에서 3시간 열처리하여 NiAl상이 형성됨을 확인할 수 있었다. NiAl상이 피복된 스테인레스강은 $650^{\circ}C$, 용융탄산염($62^{m}/_{o}Li_2CO_3-38^{m}/_{o}/K_{2}CO_{3}$)내에서 침지시험을 통해 내식성이 평가되었는데, AISI 316 스테인레스강에 비해 우수한 내식성을 보였다. 이는 표면에 치밀하게 형성된 AI 산화물층에 의한 것으로 판단되었다.

  • PDF

Determination of Fatty Acid Composition in Peanut Seed by Near Infrared Reflectance Spectroscopy

  • Lee, Jeong Min;Pae, Suk-Bok;Choung, Myoung-Gun;Lee, Myoung-Hee;Kim, Sung-Up;Oh, Eun-young;Oh, Ki-Won;Jung, Chan-Sik;Oh, In Seok
    • 한국작물학회지
    • /
    • 제61권1호
    • /
    • pp.64-69
    • /
    • 2016
  • This study was conducted to develop a fast and efficient screening method to determine the quantity of fatty acid in peanut oil for high oleate breeding program. A total of 329 peanut samples were used in this study, 227 of which were considered in the calibration equation development and 102 were utilized for validation, using near infrared reflectance spectroscopy (NIRS). The NIRS equations for all the seven fatty acids had low standard error of calibration (SEC) values, while high R2 values of 0.983 and 0.991 were obtained for oleic and linoleic acids, respectively in the calibration equation. Furthermore, the predicted means of the two main fatty acids in the calibration equation were very similar to the means based on gas chromatography (GC) analysis, ranging from 36.7 to 77.1% for oleic acid and 7.1 to 42.7% for linoleic acid. Based on the standard error of prediction (SEP), bias values, and $R^2$ statistics, the NIRS fatty acid equations were accurately predicted the concentrations of oleic and linoleic acids of the validation sample set. These results suggest that NIRS equations of oleic and linoleic acid can be used as a rapid mass screening method for fatty acid content analysis in peanut breeding program.

Use of Near-Infrared Spectroscopy for Estimating Fatty Acid Composition in Intact Seeds of Rapeseed

  • Kim, Kwan-Su;Park, Si-Hyung;Choung, Myoung-Gun;Jang, Young-Seok
    • Journal of Crop Science and Biotechnology
    • /
    • 제10권1호
    • /
    • pp.13-18
    • /
    • 2007
  • Near-infrared spectroscopy(NIRS) was used as a rapid and nondestructive method to determine the fatty acid composition in intact seed samples of rapeseed(Brassica napus L.). A total of 349 samples(about 2 g of intact seeds) were scanned in the reflectance mode of a scanning monochromator, and the reference values for fatty acid composition were measured by gas-liquid chromatography. Calibration equations for individual fatty acids were developed using the regression method of modified partial least-squares with internal cross validation(n=249). The equations had low SECV(standard errors of cross-validation), and high $R^2$(coefficient of determination in calibration) values(>0.8) except for palmitic and eicosenoic acid. Prediction of an external validation set(n=100) showed significant correlation between reference values and NIRS estimated values based on the SEP(standard error of prediction), $r^2$(coefficient of determination in prediction), and the ratio of standard deviation(SD) of reference data to SEP. The models developed in this study had relatively higher values(> 3.0 and 0.9, respectively) of SD/SEP(C) and $r^2$ for oleic, linoleic, and erucic acid, characterizing those equations as having good quantitative information. The results indicated that NIRS could be used to rapidly determine the fatty acid composition in rapeseed seeds in the breeding programs for high quality rapeseed oil.

  • PDF

입자에 의한 항공기 플룸의 열복사 가열에 관한 연구 (Investigation of the Radiative Heating from Aircraft Plume with Particles)

  • 고건영;이경주;이성남;김원철;백승욱;김만영
    • 한국항공우주학회지
    • /
    • 제40권9호
    • /
    • pp.737-744
    • /
    • 2012
  • 유한체적법을 이용하여 설정된 가상의 노즐 조건에 따라 비행체 배기플룸의 SE와 PE에 의한 열복사 저부가열 해석 연구를 수행하였다. 저부면에서의 복사열유속을 얻기 위해 배기플룸은 흡수, 방사 및 산란하는 매질을 고려하였다. 저부면은 차가운 흑체이고 비회색가스와 입자의 복사 물성치는 회색가스가중합법(WSGGM)을 사용하였다. 후방 몬테카를로 방법을 사용한 기존의 연구와 비교하여 검증한 후, 입자의 농도, 온도, 그리고 등방성 또는 이방성 산란에 따른 복사저부가열을 해석하였다. 그 결과, 복사열유속은 노즐 출구와의 거리가 멀어지거나 비행 고도가 증가할수록 감소하고 입자의 온도가 높아질수록 복사열유속은 증가한다. 또한 전방산란은 PE를 증가시키고 후방산란은 SE를 증가시켰다.

급성 호흡부전으로 사망한 황산구리 중독 1례 (Acute Respiratory Failure due to Fatal Acute Copper Sulfate Poisoning : A Case Report)

  • 김건배
    • 대한임상독성학회지
    • /
    • 제13권1호
    • /
    • pp.36-39
    • /
    • 2015
  • Copper sulfate is a copper compound used widely in the chemical and agriculture industries. Most intoxication occurs in developing countries of Southeast Asia particularly India, but rarely occurs in Western countries. The early symptoms of intoxication are nausea, vomiting, diarrhea, and abdominal cramps, and the most distinguishable clue is bluish vomiting. The clinical signs of copper sulfate intoxication can vary according to the amount ingested. A 75-year old man came to our emergency room because he had taken approximately 250 ml copper sulfate per oral. His Glasgow Coma Scale (GCS) score was 14 and vital signs were blood pressure 173/111 mmHg, pulse rate 24 bpm, respiration rate 24 bpm, and body temperature $36.1^{\circ}$ .... Arterial blood gas analysis (ABGa) showed mild hypoxemia and just improved after 2 L/min oxygen supply via nasal cannula. Other laboratory tests and chest CT scan showed no clinical significance. Three hours later, the patient's mental status showed sudden deterioration (GCS 11), and ABGa showed hypercarbia. He was arrested and his spontaneous circulation returned after 8 minutes CPR. However, 22 minutes later, he was arrested again and returned after 3 minutes CPR. The family did not want additional resuscitation, so that he died 5 hours after ED visit. In my knowledge, early deaths are the consequence of shock, while late mortality is related to renal and hepatic failure. However, as this case shows, consideration of early definite airway preservation is reasonable in a case of supposed copper sulfate intoxication, because the patients can show rapid deterioration even when serious clinical manifestation are not presented initially.

  • PDF

수계 내 조류 제거를 위한 전기응집 운전 특성 평가 (Evaluation of Operation Parameters for the Removal of Algae by Electro-Coagulation)

  • 정권;김도군;김석구;김원재;고석오
    • 한국물환경학회지
    • /
    • 제31권2호
    • /
    • pp.94-102
    • /
    • 2015
  • Electro-coagulation experiments were conducted with aluminum (Al) or iron (Fe) electrode in order to determine the optimal electrode material and operation conditions for algae removal. Al electrode showed higher removal rate of algae than Fe electrode because Al flocs have positive surface charges which electrostatically attract algae species having negative surface charges. Removal rate of algae and total phosphorous (T-P) was increased as current density and electrode area increases. It was also found that initial pH with neutral range was optimum for T-P removal by electro-coagulation. Bench-scale continuous flow experiments consisted of electro-coagulation reactor, agitation tank and settling tank were conducted. In electro-coagulation reactor, a large fraction of Al flocs were distributed to scum layer, due to the gas bubbles generated by electrolysis reaction. In agitation tank, most of Al flocs were settled and the optimal mixing intensity was found to be 50 rpm to achieve good settleability. The removal rate of algae was about 90-95%. Additionally, the removal rate of the T-P and COD was observed to be $73.8{\pm}8.0%$ and $75.0{\pm}3.8%$, respectively. Meanwhile, the removal rate of total nitrogen (T-N) was relatively low at only 24%.