• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.309-317
• /
• 2007

In this study, we conducted a vibration fatigue analysis of the lower control arm in a vehicle suspension system. The vehicle was driven during the tests so that the dynamic effects could be taken into account. The dynamic load of the frequency domain was superimposed on the frequency response analysis. We performed a virtual proving ground test using multi-body dynamics, along with a finite element analysis and fatigue life predictions. Shape optimization was also considered using the design of the experimental approach, and a response surface analysis was performed to improve the durability performance of the lower control arm. We identified the elements that had the most influence on the optimal shape of the finite element model and analyzed the sensitivity of those elements. Then the optimal points that minimized the amount of damage to the areas of interest were determined through a response surface analysis. The results suggested that the fatigue life of the model increased as its mass was not increased excessively, and demonstrated that these design procedures yielded an appropriate optimized lower control arm model.

• Explosives and Blasting
• /
• 제20권2호
• /
• pp.7-19
• /
• 2002

The cut is placed high up in the section, the 1st sloping holes below the cut, and divided all the holes located below the 1st sloping holes into a certain area with longitudinal section, to lower pollution made from tunnel blasting. With the sequential blasting machine, after I first blasted holes around the cut holes by a pre-splitting method, blasted the cut area and the 1st sloping holes. The 1st and 2nd sloping holes divided areas are initiated gradually to free face upwards made by the cut. Especially, I pre-splinted contour holes previous blast the before sloping holes from the contours. The ground vibration from the earth surface just over the advance face decreased about 42.0% compare with the down blasting method under the condition of equal charge weight per delay. I controlled the crack and over break of the mother rock by pre-splitting contour holes before blast the first sloping holes from the contours. The peak values of noise and air blast by blasting decreased about 10dB more than the down blasting method. the noise and air blast diminished gradually as a round. The throw distance of the fly rock was decreased about 55%.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 한국지진공학회 1998년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring 1998
• /
• pp.106-112
• /
• 1998

A numerical experiment is conduced to study the wave screening effectiveness of wave barriers which are constructed to reduce the ground-transmitted vibration. The finite element method is used for the simulation of the wave propagation behavior. In order to reduce the computational burden the absorbing boundary's one employed. Validity of the numerical model is checked by comparing the results with the published data. The screening effectiveness of the in filled trenches is then studied for different trench dimensions and material properties.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.383-389
• /
• 1998

A numerical study is conducted to examine the wave scattering at infilled trenches which may be constructed to reduce the ground-transmitted vibration. The finite element method is used for the simulation of the wave propagation in the semi-infinite region. In order to keep the computational burden manageable, the absorbing boundaries are employed. The numerical technique is validated by modeling a published problem. The results are shown to be in good agreement with the published data. The screening effectiveness of the infilled trenches is then studied for different trench dimensions and material properties.

• Explosives and Blasting
• /
• 제29권2호
• /
• pp.32-42
• /
• 2011

For blasting vibration analysis, there are mostly two methods, firstly, far field vibration analysis to estimate limit of building damage, secondly, near field subterranean vibration analysis to estimate rock damage and subterranean structure facilities. The former has been mainly used in our country and aboard, the latter is mostly analysed by using Homberg's model. In this model, basic input data are acquired in far field surface vibration. But in the consideration of the results of being conducted in this area over the past few decade, it is required that Homberg's model is modified. For the purpose of this, measurements of near field vibration were first conducted in our country. But it was only proposed the measurement method and the method of analysis or prediction was not suggested. Accordingly, in this paper, measurements of near field subterranean vibration were conducted and the method of analysis or prediction of near field subterranean vibration would be suggested.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.389-394
• /
• 2011

Existing FPS(Friction Pendulum System) is isolation system which is possible to isolate structures by pendulum characteristic from ground vibration. Structural natural frequency could be decided by designing the radius of curvature of FPS. Thus, response vibration could be reduced by changing natural frequency of structures from FPS. But effective periods of recorded seismic wave were various and estimation of earthquake characteristic could be difficult. If effective periods of seismic wave correspond to natural frequency of structures with FPS, resonance can be occurred. Therefore, CFPBS(Cone-type Friction Pendulum Bearing System) was developed for controlling the response acceleration and displacement by the slope of friction surfaces. Structural natural frequency with CFPBS can be changed according to position of ball on the friction surface which was designed cone-type. Therefore, Divergence of response could be controlled by CFPBS which had constantly changing natural frequency with low modal participation factor in wide-range. In this study, Seismic performance of CFPBS was evaluated by numerical analysis and shaking table test.

• Journal of the Korean Society for Precision Engineering
• /
• 제24권1호
• /
• pp.37-46
• /
• 2007

The vibration environment essentially companied by vehicle operation on the ground is determined by the shape of road surface, which is called profile. This paper focuses on development of a profile and severity measurement system for unpaved test courses. In general, the profile and severity of unpaved road is an important issue in the reliability of endurance test. In order to measure unpaved road profile and severity, it is necessary to develop a profilometer system. The developed profilometer system is composed of data processing computer, power unit, air compressor and sensors(encoder, vertical gyro and laser displacement) This paper presents the measuring system configuration, measurement principle of road profile and analysis method of road characteristics used at CPG(Changwon Proving Ground) for this purpose.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.423-423
• /
• 2005

A carbon nanotube-based nanoelectromechanical device in resonance is examined theoretically. Mechanical deflections are electrically induced and resonantly excited at the fundamental frequency in cantilevered carbon nanotube. The electrically conducting elastic beam with van der Waals interactions at the tip is used for the modeling of the carbon nanotube device. Due to the elastic, electrical, and van der Waals interactions, the total energy of the system shows the unsymmetric two-well potentials. The predictions can be made that the device exhibits its nonlinear dynamic features in the two-well potentials. Also it is predicted that the fundamental frequency of the carbon nanotube device was changed by the nonlinear interactions induced by electrical and van der Waals potentials between carbon nanotube and ground surface of the device.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 한국지진공학회 2002년도 추계 학술발표회 논문집
• /
• pp.123-130
• /
• 2002

The ground-borne vibration from pile driving is causing many public discontents. However, because of the fact that the characteristics of wave propagation and attenuation are not well understood, systematic and effective vibration reduction measures can not be taken. This paper attempts to study the propagation of stress waves induced by the pile driving. To simulate the wave propagation in a semi-infinite domain, the so-called absorbing boundaries are incorporated in the finite element method and a series of numerical simulations is performed. Numerical results show that the surface displacement and velocity increase first and then decrease as the pile penetration depth becomes larges.

• Journal of Pharmaceutical Investigation
• /
• 제35권4호
• /
• pp.279-285
• /
• 2005

Ground CS-891 (N-[1-(4-methoxyphenyl)-1-methylethyl]-3-oxo-4-aza-5a-androst-1-ene-$17{\beta}$-carboxamide) of poorly water soluble drug was obtained using a Heiko Seisakusho model TI-100 vibration mill, and samples with different crystallinity were prepared at mixture ratios of 10:0, 7:3, 5:5, 3:7 and 0:10 (intact;ground CS-891). Physicochemical characterizations were obtained using qualitative and quantitative X-ray diffractometry, different scanning calorimetry (DSC), scanning electron microscopy (SEM), Quantasorb surface area analyzer, and controlled atmosphere microbalance. With increase of amorphous CS-891 in mixture ratios, the intensities of X-ray diffraction peaks of crystalline CS-891 were decreased, whereas surface area, water absorption, and exothermic peaks in DSC were increased. The apparent solubility of ground CS-891 was $4.4\;{\mu}g/ml$ and the solubility of intact CS-891 was $3.1\;{\mu}g/ml$ at $37{\pm}1^{\circ}C$. The apparent precipitation rates of CS-891 in a supersaturated solution during the solubility test were increased with an increase of amorphous CS-891, and a crystalline form of CS-891 transformed from amorphous CS-891 after the solubility test was found by X-ray diffraction analysis, DSC and SEM. The dissolution profiles of CS-891 with different crystallinity at $37{\pm}1^{\circ}C$ by the USP paddle method were investigated, and the apparent dissolution rate constant of ground CS-891 was about 5.9-fold higher than that of intact CS-891. A linear relationships between the crystallinity of CS-891 and the apparent dissolution rate constant (r>0.96) were obtained.