• Journal of the Korean GEO-environmental Society
• /
• v.25 no.6
• /
• pp.5-12
• /
• 2024

Currently, a grouting method that minimizes damage to the reservoir embankment by injecting solidification agent at low pressure is commonly used to ensure waterproofing and safety of the embankment, but the use of solidification agents can cause issues, such as a decrease in durability and a lack of clear method for determining the mixing ratio. In this study, when the base ground and solidification agent were stirred and mixed at various weight mixing ratios, the permeability coefficient and strength of the mixture were confirmed through laboratory tests, and the optimal mixing ratio was suggested through analysis of the test results. The specimen for the laboratory test was produced considering the mixing ratio of the solidification agent. The specimen for the permeability coefficient test was tested by producing one each of cohesionless and cohesive soil for a mixing amount of 1.5 kN/m³ of solidification agent, and the permeability test results confirmed that the water barrier performance was secured below the permeability coefficient value required by various design criteria. A total of 24 specimens for the strength test were produced, 3 for each of 5 mixing amounts for cohesive soil and 3 mixing amounts for cohesionless soil. The strength test results showed that the uniaxial compressive strength tends to increase linearly with increasing curing time for both cohesionless soil and cohesive soil when the mixing amount is less than 2.0 kN/m³. Therefore, the optimal mixing ratio applied to the site is determined to be mixing amount of 1.5 kN/m³ and 2.0 kN/m³. Finally, numerical analysis reflecting test results was conducted on design case for improvement projects for aging reservoirs embankment to verify the water barrier performance and safety improvement effects.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.3
• /
• pp.21-30
• /
• 2017

Cement grouting method is generally applied for the purpose of reinforcement of deteriorated reservior. Problems have been raised due to the limit of the injection material. In order to solve these problems, various grout materials have been developed. However, there are many cases in which the grounds are disturbed in actual field. In this study, the physical properties of hybrid grout with high fineness and high viscosity characteristics were analyzed to enable penetration into the ground. Optimum inflation agent was selected and mixed with the grout. The pressure and compaction effect on expansion was examined and its effectiveness was verified. From the result of confirming expansion ratio, uniaxial compressive strength, expansion pressure and compaction effect, the HI-E (2%) sample was analyzed to be excellent in improvement effect by the inflation agent. Hence, hybrid grout can be effectively applied for the impermeable and reinforcement method of deterioration reservoir and tide embankment.

• Tunnel and Underground Space
• /
• v.18 no.2
• /
• pp.98-106
• /
• 2008

When a tunnel is excavated in a rock mass of poor condition, the adjacent zone of excavation surface may be reinforced by adopting the appropriate methods such as grouting and rock bolting. The reinforced effect can be evaluated by use of various numerical approaches, where the reinforcing elements may be expressed as distinct discretizations or smeared into the equivalent material properties. In this study, a simple numerical method, which can be classified as the latter approach, was developed for the elasto-plastic analysis of a circular tunnel. If a circular tunnel in a Mohr-Coulomb rock mass is reinforced to a finite thickness, the reinforced annulus may have different material properties from the in-situ rock mass. In the proposed elasto-plastic method for assessing the reinforcing effect, Lee & Pietruszczak (2007)'s method is applied to both the reinforced annulus and the outer insitu rock mass of the fictitious tunnel, and then two results are combined by enforcing the compatibility condition. The method were verified through comparing the results with the proposed method and the commercial finite difference code FLAC. When taking the variation of deformation modulus and strength parameters in the reinforced zone into account, the distributions of stress and radial displacement were much different from those obtained with the assumption of homogeneous rock mass.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.4
• /
• pp.59-77
• /
• 2015

In order to meet the new requirements for landfill materials, this study planned a study to apply mixed soil of mixing bottom ash and coastal dredged soil to the dredged ground. Coal ash generated from thermal power plant is divided into fly ash and bottom ash. In the case of fly ash, many studies have been conducted because small particles causes permeability coefficient to be small during recycling so no problem has been raised in the environmental area but the utilization of bottom ash has been limited because environmental problems have been raised during recycling due to its larger particle size and greater permeability coefficient. According to recently published studies, however, the results of the study that conducted the water analysis of leachate generated in the ground improvement section using bottom ash showed that heavy metal contamination levels were found to be within the reference value and no significant environmental problems were found so utilization of bottom ash is evaluated to increase significantly in the future. This bottom ash has the particle size of sand and only transportation costs need to be considered when providing materials because the majority has been disposed and it is judged as the most suitable material in dredging landfill in the economic aspect because most thermal power plants are located in the coast and transportation costs can be reduced by ship. Also, research on mixed soil that can maximize the effect of the construction period and construction cost savings than dredged soil is determined as needed because the demand for coastal dredging reclamation is increasing such as Saemangeum project etc. Therefore, we studied self-weight consolidation characteristics depending on sample processing and mixing method of mixed soil by carrying out interior self-weight consolidation experiments on mixed soil of mixing bottom ash and Kaolinite according to the new development needs of recent coastal reclaimed ground and these result findings are expected to be used as basic data when applying the large coastal dredged ground in the future.

• Journal of Biosystems Engineering
• /
• v.7 no.1
• /
• pp.17-32
• /
• 1982

The binders introduced in Korea were originally designed to be used for Japonica-type varieties which have relatively long stem and are highly resistant to shattering. In order to use it for Tongil varieties which are short and easy to be shattered, mechanical modifications are necessary to reduce a grain loss incurred during binder operation. This study was intended to investigate analytically and experimentally the major sources of grain losses caused by three kinds of binders now introduced in Korea. Actual modification for each of three binders was done and experimentally compared to see if any improvement on grain loss was achieved. The results obtained in this study are summarized as follows; 1. It was required that the power transmission of binder should have a shifting mechanism so that velocities of pick-up and traveling units could be changed independently as desired according to the Japonica-type and Tongil varieties. In other words, the desired velocity of traveling unit should be obtained by shifting the transmission and the velocity of pick-up unit should be selected by reaping clutch according to the variety independent of the velocity of traveling unit as shown in Fig. 6. 2. To reduce grain loss it was desired that the moving parts of the pick-up unit should have the lowest possible velocities in harvesting Tongil varieties, unless the reduction of the speed be hindered the conveyance of the material. Based on the study, it was concluded that the velocities of pick-up unit be reduced by about 35% of those of the existing units. 3. It was found that the lug at the upper rotating section of pick-up case gave a severe impact on the ears of rice to increase grain loss. The optimum design of pick-up case to protect the ears from the protruding part of the lug was recommended by the result of analysis of the trajectory of the end-point of lug at the position. 4. It was proved analytically and experimentally that pick-up unit at the lower-rotating part was the other important source of grain loss in pick-up and divider assembly. In order to reduce a grain loss incurred by lugs at their lower-rotating section, it was suggested to improve it by (1) widening the space between right and left lower-rotating section, (2) shortening the length of lugs, (3) enlargement of the angle between the pick-up case and ground-level, and (4) attaching guard to right and left dividers so that the rotating lug could not give a high impact to the paddy hill. 5. Pick-up and divider assembly of the original binder of three models studied was modified according to the suggestions that were given by the preliminary study. Field test showed that the modified binders were able to reduce grain losses by about 0.4-0.7 percentage points compared to those without modification.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.180-195
• /
• 2000

Grouting has been practiced as a reliable technique to improve the mechanical properties of rock mass. But, the study of ground improvement by greeting is rare especially in jointed rock mass. In this study, joint compression test and direct shear test were performed on pure rock joint and cement milk grouted rock joint to examine the grouting effect on the property of rock joint. In the pure rock joint compression test, joint closure varied non-linearly with normal stress. But after cement milk grouting, the normal deformation characteristics of the joint was linear at the low normal stress level. As normal stress increased. deformation of the sample rapidly increased due to the stress concentration at the joint asperities. Peak shear strength of the grouted joint in low normal stress was higher than that of non-grouted joint due to the cohesion, decreased exponetially as the grout thickness increased. Thus after cement milk grouting, the failure envelope modified to a curve that has cohesion due to grout material hydration with decreased friction angle. Shear stiffness and peak dilation angle of the grouted joint decreased as the grout thickness increased. The peak shear strength from the direct shear test on grouted rock joint was represented by an empirical equation as a fuction of grout thickness and roughness mean amplitude.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.32 no.3
• /
• pp.1-17
• /
• 2004

The focus of this study is the promotion of green area volumes and their naturalness, water circulation system, decline of entropy, creation of biological habitats and linkage of separated urban green space. Re-presentative urban biotope survey sites were categorized as urban biotope, semi-natural biotope, and natural forest. In the urban biotope, a residential biotope was constructed near the Han river and in mountain areas. The green-area ratio at the housing complex was about 25%. GVZ(Grunvolumenzahl) was 0.35m$^3$/m$^2$ at the 5∼10-story housing complex, and 1.53m$^3$/m$^2$ over the 11-story. As for the green-area structure of the housing complex, canopy layer, understory layer, and shrub layer were not differentiated and the green-area volume was not high enough. The green-area ratio of school areas as a public area biotope was 5∼20%. GVZ was 1.12m$^3$/m$^2$ at Myungduk High School, and 1.78m$^3$/m$^2$ at Jeonggok Elementary School. In order to convert the urban biotope into an ecological area, green areas around the buildings should be connected to urban buffer green areas, and multi-layer structures should be established with natural plant species. In the semi-natural biotope, neighbor parks were created park in the vicinity of the natural forests. GVZ was 0.28m$^3$/m$^2$, and plantation was established with single layer structure and was definitely insufficient for the area. The urban buffer green areas have been established in strip corridors with the width of 20∼123m. In those areas, GVZ was 0.16∼0.27m$^3$/m$^2$ and had a deficient canopy layer, understory layer, and shrub layer. Soil conditions were not favorable for tree growth. In the natural biotope, GVZ of the plantation was 1.03∼1.5m$^3$/m$^2$ but the high crown closure of this area reduces the chance of species change and succession. GVZ of natural forest was 2.53∼2.57m$^3$/m$^2$. It is desirable to plant diverse plants and the natural forest should be succeeded by broad-leaf deciduous tree species. To improve the value of biotope at Kangseo-Gu, building height needs to be limited to reduce the environmental deterioration in the city. In order to maintain the water circulation system, water-permeable material is recommened when the urban surface areas are paved. The establishment of a water circulation system will improve ground water levels, soil moisture, water quality, and habitats. In order to improve biological diversity, it is desirable to have multi-layer structures in urban green areas with native species.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.164-172
• /
• 2020

The fuel oil/heat exchanger installed in military aircraft is a device that cools the lubricant oil supplied to other devices, such as an AMAD, and a hydraulic pump using the low temperature of the fuel is cracked at the AMAD lubricant inlet port. If a crack in the heat exchanger occurs, the lubricant oil supplied to other equipment is not cooled. Therefore, the flight can no longer be performed. In this study, non-destructive inspection and microscopic examination of the fracture surface of the oil port were performed to analyze the crack tendency. The oil pipe connected to the oil port is a titanium pipe, which is fastened with over torque and has been identified as the leading cause of heat exchanger oil port cracks. In addition, it was verified as the main reason for cracking by finite element analysis. The material and diameter of the pipe were changed to improve this defect, and the applied torque was adjusted. In addition, the bending value of the pipe was adjusted to minimize the fatigue accumulation due to pulsating pressure. As a result, no cracks occurred on the heat exchanger via the ground test after the installation of an improved pipe under the same conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.61-68
• /
• 2020

In this study, the international standard ISO TS 16774 Part 3 Test Method for Water (wash out) Resistance and KS F 4935 ｢Sealant Injection type for water leakage maintenance of adhesive flexible rubber asphalt series｣, which are standardized as a quality control method of injection type repair materials used for water leakage cracks in underground concrete structures, are currently used in Korea. As a result, considering the performance criteria of "mass change rate -0.1%" stipulated in KS F 4935, the remaining 13 types repair materials, excluding RG-2 of synthetic rubber and UG-1 of urethane, need to be reviewed for stabilization of the loss resistance due to the flow of ground water. The results of this study are determined to be available as a basic indicator for the selection of repair materials used for cracks in concrete structures. In addition, it is expected that the results of this study can be utilized as reference data that can be reflected in the improvement of the quality of repair materials that will be researched and developed later.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.204-210
• /
• 2022

Cement is pointed out as the main cause of carbon dioxide emission in the construction industry. Many researchs are underway to use blast furnace slag, an industrial by-product, as a substitute for cement to reduce carbon dioxide emitted during the manufacturing the cement. When blast furnace slag is used as a substitute for cement, it has advantages such as long-term strength and chemical resistance improvement. However, blast furnace slag has a problem that makes initial strength low. This is due to the impermeable film on the surface created during the production of blast furnace slag. The created film is known to be destroyed in an alkaline environment, and based on this, previous studies have suggested a solution using various alkali activators. But, alkali activator is dangerous product since it is a strong alkaline material. And it has the disadvantage in price competitiveness. In this study, an experiment was conducted to improve the initial hydration reactivity of the blast furnace slag to secure the initial strength of the mortar substituted with the blast furnace slag and to check whether the carbonation resistance was increased. As a result of the experiment, it was confirmed that the mortar using alkaline water showed higher strength than the mortar using tap water, and there were more hydration products generated inside. In addition, it was confirmed that the mortar using alkaline water as a compounding water had high carbonation resistance.