• Journal of Radiation Protection and Research
• /
• v.29 no.2
• /
• pp.91-96
• /
• 2004

A practical methodology for the determination of derived intervention levels (DILs) on relocation following an accidental release of radionuclides was designed based on dose rate on the ground. The influence of DILs was investigated with respect to the change of parameter values, which are dependent on socio-environmental characteristics in distinction from temporary and permanent relocations. The DILs on relocation showed a distinct difference depending on effective removal half-life of radionuclides following a deposition, delay time in measurement and residential characteristics. In particular, the delay time. In measurement was an important factor in determination of DILs in the case of an assumption that dose rate on the ground declines in a power function, not in an exponential function. The DILs showed lower numerical values as longer effective half-life, longer delay time In measurement and longer exposure time.

• Journal of the Optical Society of Korea
• /
• v.16 no.1
• /
• pp.76-79
• /
• 2012

$Tb_3Al_5O_{12}:Ce$ (TAG:Ce) thin films were successfully deposited by a pulsed laser ablation method on a quartz substrate, and low-temperature post-annealing effects on luminescent properties were investigated in detail. TAG:Ce thin films were analyzed by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and photoluminescence spectroscopy. The as-deposited films were amorphous, and post-annealing above $700^{\circ}C$ was required for crystallization. The post-annealed TAG:Ce thin films showed strong and broad emission bands around 542 nm and excitations at 451 nm, which all corresponded to transitions between the 4f ground level to the $5d^1$ excited levels of Ce ion.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1546-1548
• /
• 1998

Dual mode ring resonators(DMRR) have been fabricated using laser ablated $YBa_2Cu_3O_{7-x}$ superconducting thin films. The transition temperature of YBCO thin films were 85 - 88 K and the film thicknesses were about 5,000 $\AA$. Dual mode ring resonators were patterned by standard photolithography process and wet-etching. Then two-layer metal thin films (Ti/Ag) have been deposited for the ground plane on the back side of substrate by e-beam and thermal evaporation. The input/output feedline angles of each resonator were $60^{\circ}$, $100^{\circ}$, $180^{\circ}$. A network analyzer was used for testing the performance of the resonators in the frequency range of 6-13 GHz at 77 K.

• Journal of Life Science
• /
• v.11 no.2
• /
• pp.153-158
• /
• 2001

To investigate the effects of soil acidification on growth of Impatiens balsamina L. plants were transplanted to acidified soils with H$_2$SO$_4$ solution. The concentrations of soluble Ca, Mg, K, Al and Mn in the acidified soils increased with increment of H$^{+}$ addition to the soil. In both species, the plant height and root length were inhibited by soil acidification, showing much severer inhibition in Impatiens balsamina L. than in Tagetes patula L., As the soil pH decreases, the growth of underground parts decreased greatly than that of above ground parts in both species. Total dry weight decreased with increased Al concentration as well as lowered soil pH in both plants. There was a strong positive correlation between relative total dry weight and molar (Ca+Mg+K) / Al ratio of the soil. The results suggest that molar(Ca+Mg+K)/ Al ratio of the soil may be useful indicator for assessing the critical load of acid deposition in herb species.s.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.55-60
• /
• 2020

This study designed High impedance filter to reduce RF loss to heater heating wire and increase RF current flowing to heater ground wire. Effects such as D / R improvement and process reproducibility could be seen. In addition, RF parameter distribution optimization was possible by understanding the RF path of PE-CVD equipment using Plasma and designing filter.

• Journal of Korea Water Resources Association
• /
• v.43 no.10
• /
• pp.883-891
• /
• 2010

More recently, there have been significant changes in the forms of channels due to runoff characteristics driven by climate changes and other alterations in basin/channel environments. Particularly, increasing local deposition in major channels is being observed nationwide. Of such phenomena, it is noteworthy that flood-plains show unidirectional growth and lowering of channels within compound channels in the form of a high-flow plain. These changes are supposed to affect management of the river ecology as well as flood control. In this study, the research on channels in Korea confirmed that the phenomenon of local deposition in those channels is actually taking place, rendering a problem to be urgently addressed. Previous studies on bed changes have been focused on low channels based on bed materials distributed over the channels. However, this research has proved that surface-layer deposition of a high-flow plain is closely related with changes in the conditions of ground surfaces and, ultimately, affects the bed of the entire channel as well. According to the intensive research on the condition of the high-flow plain of the mouth of the Han River, the silt deposited in the high-flow plain was the main cause of settlement/growth of vegetation. And this leads to landforming along with woods-forming, disturbing flood control as well as the normal river ecology.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.34-34
• /
• 2012

Heavy storms rainfall has caused many landslides and slope failures especially in the mountainous area of the world. Landslides and slope failures are common geologic hazards and posed serious threats and globally cause billions in monetary losses and thousands of casualies each year so that studies on slope stability and its failure mechanism under rainfall are being increasing attention of these days. Rainfall-induced slope failures are generally caused by the rise in ground water level, and increase in pore water pressures and seepage forces during periods of intense rainfall. The effective stress in the soil will be decreased due to the increased pore pressure, which thus reduces the soil shear strength, eventually resulting in slope failure. During the rainfall, a wetting front goes downward into the slope, resulting in a gradual increase of the water content and a decrease of the negative pore-water pressure. This negative pore-water pressure is referred to as matric suction when referenced to the pore air pressure that contributes to the stability of unsaturated soil slopes. Therefore, the importance is the study of saturated unsaturated soil behaviors in evaluation of slope stability under heavy rainfall condition. In an actual field, a series of failures may occur in a slope due to a rainfall event. So, this study attempts to develop a numerical model to investigate this failure mechanism. A two-dimensional seepage flow model coupled with a one-dimensional surface flow and erosion/deposition model is used for seepage analysis. It is necessary to identify either there is surface runoff produced or not in a soil slope during a rainfall event, while analyzing the seepage and stability of such slopes. Runoff produced by rainfall may result erosion/deposition process on the surface of the slope. The depth of runoff has vital role in the seepage process within the soil domain so that surface flow and erosion/deposition model computes the surface water head of the runoff produced by the rainfall, and erosion/deposition on the surface of the model slope. Pore water pressure and moisture content data obtained by the seepage flow model are then used to analyze the stability of the slope. Spencer method of slope stability analysis is incorporated into dynamic programming to locate the critical slip surface of a general slope.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.696-706
• /
• 2023

Consequences of an anticipated Beyond Design Basis Accident (BDBA) Long-Term Station Blackout (LTSBO) event with complete loss of grid power in the VVER-1200 reactor of Rooppur Nuclear Power Plant (NPP) of Unit-1 are assessed using the RASCAL 4.3 code. This study estimated the released radionuclides, received public radiological dose, and ground surface concentration considering 3 accident scenarios of International Nuclear and Radiological Event Scale (INES) level 7 and two meteorological conditions. Atmospheric transport, dispersion, and deposition processes of released radionuclides are simulated using a straight-line trajectory Gaussian plume model for short distances and a Gaussian puff model for long distances. Total Effective Dose Equivalent (TEDE) to the public within 40 km and radionuclides contribution for three-dose pathways of inhalation, cloudshine, and groundshine owing to airborne releases are evaluated considering with and without passive safety Emergency Core Cooling System (ECCS) in dry (winter) and wet (monsoon) seasons. Source term and their release rates are varied with the functional duration of passive safety ECCS. In three accident scenarios, the TEDE of 10 mSv and above are confined to 8 km and 2 km for the wet and dry seasons, respectively in the downwind direction. The groundshine dose is the most dominating in the wet season while the inhalation dose is in the dry season. Total received doses and surface concentration in the wet season near the plant are higher than those in the dry season due to the deposition effect of rain on the radioactive substances.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.71-74
• /
• 1999

We have fabricated high-T$_c$ superconducting YBa$_2Cu_3O_{7-{\delta}}\;/SrTiO_3/\;YBa_2Cu_3O_{7-{\delta}}$ (YBCO/STO/YBCO) multilayer structure on (001) $SrTiO_3$ substrate by using pulsed laser deposition technique for applying to ground plane of single flux quantum digital circuits. In this structure, the top and bottom YBCO layers were connected through the holes in the STO insulating layer. The critical temperature of the two YBCO layers connected each other was 86 K after annealing at 500 $^{\circ}C$ in $O_2$ atm for about 60 hr. This result shows that the annealing process is very important fabricating YBCO/STO/YBCO multilayer structure An experiment to optimize the fabrication process of YSCO/ST0/YBCO multilayer structure with good quality is in progress.

• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.111-125
• /
• 2018

In this study, we evaluated the uniformity of deposition rate and particle size distributions of the variable rate application technique using the unmanned rotorcraft by measuring the spray pattern according to path location in the range of spraying flight. The coefficient of variation (CV) of the lateral coverage rate for the overlapped distribution with the spray swath of 3.6 m in both guidance and auto-pilot flight modes maintaining constant flight speed was about 30% and the CV of the coverage rate by the flight path location was extremely small. Therefore, it was assessed that the variable rate application technology compensating for the variation of ground speed was superior in terms of spray uniformity. In addition, the droplet size distributions in both volume median diameter(VMD) and number median diameter(NMD) were adequate for aerial application and uniform in terms of lateral distribution. Thereafter, we intend to contribute to a precise application on small-scaled fields using the unmanned agricultural rotorcraft by the variable rate application.