• Journal of the Earthquake Engineering Society of Korea
• /
• v.20 no.4
• /
• pp.223-234
• /
• 2016

To investigate earthquake responses of structures with basements affected by soil deposits, centrifuge tests were performed using an in-flight earthquake simulator. The test specimen was composed of a single-degree-of-freedom structure model, a basement and sub-soil deposits in a centrifuge container. The test parameters were the dynamic period of the structure model, boundary conditions of the basement, existence of soil deposits, centrifugal acceleration level, and type and level of input earthquake accelerations. When soil deposits did not exist, the earthquake responses of the structures with fixed basement were significantly greater than those of the structure without basement. Also, the earthquake responses of the structures with the fixed basement surrounded by soil deposits were amplified, but the amplifications were smaller than those of the structures without basement. The earthquake responses of the structures with the half-embedded basement in the soil deposits were greater than those estimated by the fixed base model using the measured free-field ground motion. The test showed that the basement and the soil deposit should be simultaneously considered in the numerical analysis model, and the stiffness of the half-embedded was not effective.

• Journal of Satellite, Information and Communications
• /
• v.9 no.3
• /
• pp.121-126
• /
• 2014

ETRI(Electronics and Telecommunication Research Institute) has joined National GNSS Research Center program of Defense Acquisition Program Administration and Agency for Defense Development in 2010. The research subject is technology for MSAR(Military Search and Rescue) system configuration. In this project, we analyses the ways in order to improve the accuracy, reliability, availability for MSAR system from M&S(Modeling and Simulation). The MSAR System M&S Software can be used for performance analysis of new elements, such as ground elements and satellite elements without any hardware development. In this paper, after introduction of the architecture design and functional scope of the simulator, the performance analysis result for MSAR M&S software is presented.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.21-29
• /
• 2005

Lightweight Foamed Soil (LWFS) could be the substitute of normal soils used in backfill to earth structures and embankment materials far soft ground improvement in port and harbor project because of its effectiveness in settlement reduction and earth pressure decrease due to its lightness. A series of triaxial and unconfined compression tests were performed to investigate behaviors of LWFS composed of dredged soils, cement and air foam, and cured at underwater conditions. The density of LWFS will increase if LWFS is cured at underwater conditions because high water pressure makes air foam disappear or demolish during the curing compared with LWFS cured at normal air conditions. This paper is to find the mechanical behaviors of LWFS cured at seawater depth of 5.0 m and 10.0 m, respectively, which simulates underwater curing conditions by underwater pressure simulator chamber developed during this study. In addition, new normalized factor formula, which takes account of mixing design conditions determining compressive strength of LWFS, was proposed to consider mixing design factor fur LWFS.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.229-238
• /
• 2016

In this paper, we have studied isolation enhancement using a suppression of surface wave to improve performance of array antenna. To reduce isolation between elements of array antenna, perfect magnetic conductor(PMC) and SOFT-surface is designed and located at center of ground plane, isolation and gain is simulated by commercial full wave simulator(HFSS). As a result, isolation of more than 40 dB and gain improvement of 2.2 dBi are obtained at E-plane array in case of both PMC and SOFT-surface. At H-plane array, air coupling is dominant compared to coupling by surface wave. It is conclude that this study is useful for design of compact array antenna and performance improvement of array antenna.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.4
• /
• pp.772-779
• /
• 2015

In this paper,a reconfigurable multi-band mobile antenna with switching line for LTE band 13, GSM, K-PCS, WCDMA band. The proposed antenna is planar strip line design and composed of stub shorted to the ground plane and two switching line for proposed band operation. To obtain the optimized parameters, we used the simulator, Using the obtained parameters is fabricated. The numerical and experiment results demonstrated that the proposed antenna satisfied the -6 dB impedance bandwidth requirement while simultaneously covering when the state of sw1 and sw2 on for LTE band 13, the state of sw1 off and sw2 on for GSM, K-PCS, the state of sw1 off and sw2 off for WCDMA. Respectively and characteristics of gain and radiation patterns are determined for a reconfigurable multi-band mobile terminal.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.11
• /
• pp.115-120
• /
• 2005

This paper describes the design and implementation of engineering model(EM) of Mass Memory Unit(MMU) for Science and Technology Satellite 2(STSAT-2) and the results of integration test. The use of Field-Programmable Gate Array(FPGA) instead of using private electric parts makes a miniaturization and lightweight of MMU possible. 2Gbits Synchronous Dynamic Random Access Memory(SDRAM) module for mass memory is used to store payload and satellite status data. Moreover, file system is applied to manage them easily in the ground station. RS(207,187) code improves the tolerance with respect to Single Event Upset(SEU) induced in SDRAM. The simulator is manufactured to verify receiving performance of payload data.

• Journal of Satellite, Information and Communications
• /
• v.12 no.4
• /
• pp.42-49
• /
• 2017

Delay- and Disruption-Tolerant Network (DTN) has been considered as a key technology to overcome main challenges in interplanetary communications such as an intermittent connectivity and high bit error rates. The lack of end-to-end connectivity between source and destination results in long and variable delays and data loss, hence the Internet Protocols cannot operate properly in such environments because it requires an end-to-end connectivity. The DTN, which utilizes 'store-and-forward' message passing scheme between nodes, can overcome the lack of end-to-end connectivity in Interplanetary Network (IPN). In this paper, DTN is applied to 3-hop relay IPN, where messages are transmitted from Earth ground station to Lunar lander through Earth satellite and Lunar orbiter. ONE simulator is used to reflect the real environment of IPN and an efficient resource management method are analyzed to guarantee the message delivery by optimizing a message TTL (Time to Live), buffer size and message fragmentation.

• Journal of Advanced Navigation Technology
• /
• v.13 no.3
• /
• pp.319-326
• /
• 2009

In this paper, the key technologies of Navigation receiver for GNSS sensor station are presented as a development result of a GNSS ground station in ETRI. A wide-band antenna and RF/IF components and SW signal processing unit to cover the GPS and Galileo signals for GNSS receiver are developed and its performance is verified by using GPS live signal and GNSS RF signal simulator from SpirentTM. We also gather GIOVE-A signal by using H/W antenna and RF/IF units in IF-level as sampling frequency and bit number, 112MHz and 8bits, respectively by using the developed wide-band antenna and RF/IF components. Data acquisition is done by using commercial data acquisition device from National Instrument TM. The gathered data is fed into SW receiver to process Galileo E1 to verify Galileo signal processing by Galileo live signal from GIOVE-A.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.147-155
• /
• 2005

In this paper, we propose that three uniform coplanar waveguides(CPWs), such as a conventional, finite grounded(FG), and grounded(G) CPWs, can be coupled with a $TE_{01{\delta}}$ mode dielectric resonator(DR) for a parallel resonant characteristic as a microstrip line coupled with the DR. Coupling characteristics have been investigated by placing the DR on a dielectric support above the CPWs and by moving the DR away from the center of a slot of the CPWs to the ground plane. FEM simulation(HFSS) results in terms of S-parameters agree well with measurement results. Finally, unloaded Q values of the DR coupled with the three uniform CPWs are compared with those of the DR coupled with a microstrip line. The comparison shows that the DR coupled with the three CPWs has higher unloaded Qs than that coupled with a microstrip line and that the GCPW case has the highest unloaded Qs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.73-81
• /
• 2011

As high speed digital systems continue to use components with faster edge rate and clock speeds, transmission of the digital information, it can bring about many troubles. The increasing requirement for controlled impedance PCBs becomes both a critical success factor and a design challenge to implement a system. Especially, the noise sources in high frequency digital systems include the noise in power supply, ground and packaging, and they destroy the fidelity of signals. Therefore PCB design with impendence matching is needed to improve fidelity of signal in H/W. In this paper, we have developed an impedance control and analysis tool for multi-layer PCB design, and simulates the tracks controlled impedance with the test coupon. So, it can save the design time and support the economical PCB design.