• Analytical Science and Technology
• /
• v.30 no.6
• /
• pp.329-337
• /
• 2017

A major concern regarding most auto-repair shops in residential areas is the emission of odorous volatile organic compounds (VOCs) into the local atmosphere, especially during painting operations. VOCs contribute to poor local air quality and are responsible for the perceived odor and discomfort experienced by local residents. Sixteen major VOCs (6 aromatic hydrocarbons and 10 aliphatic carbonyl compounds) were selected as potential target compounds. The site was an auto-repair shop located in a central region of Seoul, South Korea, where the air quality of the site has been a subject of residents' complaints. The sampling points were as follows: 1) in the painting booth with new (NB) or old (OB) removal system, (2) in the exhaust duct after new (ND) or old (OD) odor removal filter, and (3) 2 m below the discharge vent (4 m above the ground) (outdoor air, OA). Each sample was coded: (1) before painting (BP), (2) during painting (DP), and (3) after painting (AP). The toluene level in the duct with the new removal filter during painting (ND-DP) was 1.5 ppm (v/v), while it was 3.8 ppm (v/v) in the right duct with an old removal filter during painting (OD-DP). Accordingly, the effect of filter replacement was reflected by differences in VOC levels. Therefore, accurate monitoring of odorous VOCs is an important step to reduce odor nuisance from local sources.

• Parasites, Hosts and Diseases
• /
• v.47 no.2
• /
• pp.159-165
• /
• 2009

House-residual spraying and insecticide-treated bed nets have achieved some success in controlling anthropophilic and endophagic vectors. However, these methods have relatively low efficacy in Korea because Anopheles sinensis, the primary malaria vector, is highly zoophilic and exophilic. So, we focused our vector control efforts within livestock enclosures using ultraviolet black light traps as a mechanical control measure. We found that black light traps captured significantly more mosquitoes at 2 and 2.5 m above the ground (P<0.05). We also evaluated the effectiveness of trap spacing within the livestock enclosure. In general, traps spaced between 4 and 7m apart captured mosquitoes more efficiently than those spaced closer together (P>0.05). Based on these findings, we concluded that each black light trap in the livestock enclosures killed 7,586 female mosquitoes per trap per night during the peak mosquito season (July-August). In May-August 2003, additional concurrent field trials were conducted in Ganghwa county. We got 74.9% reduction (P<0.05) of An. sinensis in human dwellings and 61.5% reduction (P>0.05) in the livestock enclosures. The black light trap operation in the livestock enclosures proved to be an effective control method and should be incorporated into existing control strategies in developed countries.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.16 no.1
• /
• pp.1-15
• /
• 1980

An underwater recording system was designed to measure the sound spectra of the underwater noises produced by fishing gears in operation. Recorded were noi~es from three types of fishing gears: an anchovy set net, three anchovy boat seine net and a stern trawlnet. Acoustic analysis were made using a heterodyne analyzer, a digital frequency analyzer and a level recorder. The no;'e produced by the anchovy set net was found in the high frequency region of the onset of ambient noise spectrum with a slope of - 6 dB/octave. Here the ambient noise spectrum is higher, though similar in shape, than Knudsen spectrum, and is attributed to the breaking action of the coastal wave. Measured noise spectra during the fishing operations of the anchovy boat seine nets are attributed to the background noise of the sea in the presence of the fishing vessels. The frequency distribution of the noise was 20~5, 000 Hz in the case of two steel anchovy boat seiners, and 20-3,000 Hz in the case of the wooden anchovy boat seiner. The predominant frequency range was 250~350 Hz and maximum sound pressure level was 122 dB (re $1\muPa$) in the case of the steel boat and ] 17 dB in the case of the wooden boat. The noises produced by the trawl fishing gears are remarkably higher than the background noi~e in the presence of the fishing vessel. The frequency distribution of the noi~e was 20-6,300 Hz. The predominant frequency range was 100~200 Hz and maximum sound pressure level was 137 dB ( re $1\muPa$) . The noise spectra were not so much different from that caused by vibrations of the towing cable and the structure of the ground rope of the trawl net towed in an experimental tank.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.2
• /
• pp.59-67
• /
• 2009

A study on fugitive dusts was conducted at Saemangeum reclaimed land located in Gim-je area. The monitoring result on the fugitive and suspended dust was significantly affected by the farming activities (harvesting and land cultivation) and vehicles passing nearby the measuring points. The concentration of the fugitive dust generated from the reclaimed land was reduced remarkably by the effect of halophyte present on the ground and the tide embankment. Comparing the data collected in 2006 and 2007, the concentrations of TSP and PM10 decreased by 47.4% and 29.5%, respectively. After harvesting operations at paddy field, TSP increased by 22% while PM10 increased by 54%. The concentration of a Cl- which is a representative ion of sea-salt decreased to about 35% in 2007 compared with 2006. This represents that the inside area change and plant covering rate affected on the decrease of fugitive dust. The correlation analysis for the compounds of topsoil at each measuring point shows that near the coastline is more comparable. The canopy of halophyte in the source area also increased which reduced the fugitive dust remarkably. The dust distribution measured by dust spectrometer at the same point shows that most particles are $0.5{\mu}m$ to 2um size but not greater than $5{\mu}m$.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.7 no.4
• /
• pp.15-23
• /
• 2004

In order to utilize remote sensed images effectively, it is necessary to correct geometric distortion. Geometric correction is a critical step to remove geometric distortions in satellite images. For geometric correction, Ground Control Points (GCPs) have to be chosen carefully to guarantee the quality of geocoded satellite images, digital maps, GPS surveying or other data. Traditional approach to geometric correction used GCPs requires substantial human operations. Also that is necessary much time and manpower. In this paper, we presented an on-line automatic geometric correction by constructing GCP Chip database. The Proposed on-line automatic geometric correction system is consists of four part. Input image, control the GCP Chip, revision of selected GCP, and output setting part. In conclusion, developed system reduced the processing time and energy for tedious manual geometric correction and promoted usage of Landsat imagery.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.11
• /
• pp.1011-1022
• /
• 2014

Currently, the wireless network environment of air node is constructed mainly of ground relay station. However, as the Korean Peninsula is composed of 70% mountainous region, there are multiple shadow zones. This is calling for effective measures to prevent aircraft from losing communication link during low-mid altitude missions. In this article we propose the utilization of Bezier Curve for estimation of aircraft flight path and control method for entering shadow zone. This method successfully estimated aircraft track, and analyzed the existence, disseminated the warning, and took measures to avoid the shadow zone before entering. This article, suggested after simulated experiments, proves that the method enables seamless communication during air operations.

• Journal of Biosystems Engineering
• /
• v.38 no.1
• /
• pp.1-8
• /
• 2013

Purpose: Path planning and tracking algorithms applicable to various agricultural operations, such as tillage, planting, and spraying, are needed to generate steering angles for auto-guidance tractors to track a point ahead on the path. An optimal coverage path algorithm can enable a vehicle to effectively travel across a field by following a sequence of parallel paths with fixed spacing. This study proposes a path generation and tracking algorithm for an auto-guided Korean tractor with a tillage implement that generates a path with C-type turns and follows the generated path in a paddy field. A mathematical model was developed to generate a waypoint path for a tractor in a field. This waypoint path generation model was based on minimum tractor turning radius, waypoint intervals and LBOs (Limit of Boundary Offsets). At each location, the steering angle was calculated by comparing the waypoint angle and heading angle of the tractor. A path following program was developed with Labview-CVI to automatically read the waypoints and generate steering angles for the tractor to proceed to the next waypoint. A feasibility test of the developed program for real-time path tracking was performed with a mobile platform traveling on flat ground. The test results showed that the developed algorithm generated the desired path and steering angles with acceptable accuracy.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.5
• /
• pp.903-909
• /
• 2010

ADAS is the air defense control system performing air surveillance and identification of ROK and near air. This system is self-developed by Air Force, currently operated successfully as the alternative system of MCRC. ADAS processes converting and combining transferred the real time radar data detected by radars. additionally, it displays significant radar data as producing in tracks. Then, it uses the message queue for IPC(Inter Process Communication). the various tactical data processed in the server is ultimately send to the network management process through the message queue for transmitting to the weapon director console. the weapon director receives this transmitted tactical data through the console to execute air defense operations. However, there is a problem that data packet is delayed or lost since the weapon Director does not receive as the amount of tactical data from the server overflowed with air tracks and missions increased. This paper improved the algorism to display and transmit the various tactical data processed from ADAS server to numbers of the weapon director console in the real time without any delay or lost. Improved the algorism, established at exercise, the development server in the real operation network and the weapon director console, is proved by comparing the number of sending tactical data packets in the server and receiving packets in the weapon director.

• Korean Journal of Remote Sensing
• /
• v.35 no.1
• /
• pp.29-37
• /
• 2019

Synthetic Aperture Radar (SAR) observations are powerful tools to monitor surface's displacement very accurately, induced by earthquake, volcano, ground subsidence, glacier movement, etc. Especially, radar interferometry (InSAR) which utilizes phase information related to distance from sensor to target, can generate displacement map in line-of-sight direction with accuracy of a few cm or mm. Due to decorrelation effect, however, degradation of coherence in the InSAR application often prohibit from construction of differential interferogram. Offset tracking method is an alternative approach to make a two-dimensional displacement map using intensity information instead of the phase. However, there is limitation in that the offset tracking requires very intensive computation power and time. In this paper, efficiency of parallel computing has been investigated using high performance computer for estimation of glacier velocity. Two TanDEM-X SAR observations which were acquired on September 15, 2013 and September 26, 2013 over the Narsap Sermia in Southwestern Greenland were collected. Atotal of 56 of 2.4 GHz Intel Xeon processors(28 physical processors with hyperthreading) by operating with linux environment were utilized. The Gamma software was used for application of offset tracking by adjustment of the number of processors for the OpenMP parallel computing. The processing times of the offset tracking at the 256 by 256 pixels of window patch size at single and 56 cores are; 26,344 sec and 2,055 sec, respectively. It is impressive that the processing time could be reduced significantly about thirteen times (12.81) at the 56 cores usage. However, the parallel computing using all the processors prevent other background operations or functions. Except the offset tracking processing, optimum number of processors need to be evaluated for computing efficiency.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.67-73
• /
• 2021

Tanks are key weapons of ground combat that are equipped with powerful weapons and have strong protective bodies. One tank component, the engine clutch flange, is located in the part of the tank where the engine and transmission are installed, and it is a key part of the power transfer and shutoff. The engine clutch flange transmits high power to secure the mobility of the tank; thus, it must have high strength and hardness. In addition, high durability and safety must be ensured because tank operations must exclude concerns about damage. In this study, an engine clutch female flange for tanks made of SNCM439 was developed. The 2D design used AutoCAD programs, and the 3D shape design used CATIA programs. The structural analysis was conducted using ANSYS. The mesh grid has a tetrahedron shape and is created by adding a mid-side node. After the mechanical properties and constraints of SNCM439 were entered, the changes in the safety factor, total deformation, and Von-Mises stress were identified according to the increase in torque. Prototype processing was performed to verify the engine clutch female flange for the tank. To determine the productivity of the product, the cutting processing time was measured when processing the prototypes. Based on the results of measuring the cutting processing time, it is concluded that research is needed to improve productivity because MCT slot cutting processing is time consuming.