• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2619-2627
• /
• 2009

The ground fault is occupying 70% among the total number of faults in ungrounded distribution power system. When the ground fault occurs in ungrounded system, the fault current is so small that it is hard to detect. But fault handling is very important because to continue power supply during fault conditions may cause the fault spreading and the distribution device in trouble. This paper presents the fault line detection method by using GPT signal detecting zero sequence voltage, and the fault section detection method by detecting whether GPT signal is disappeared or not during shifting normally open switch, which is connecting switch between distribution lines with open state in order to restore the outage area under emergency situation, and during isolating each section one by one which belongs to the fault line. This method is efficient because there is no whole power interruption during the fault section detection, and it is possible to perform both the fault section detection and the service restoration for the outage area at the same time, and it can apply to various distribution system configuration. Program for the fault restoration was developed applying proposed method, and it has been validated by applying to the pilot project of distribution automation system in Vietnam which has the ungrounded distribution system.

• Journal of Advanced Navigation Technology
• /
• v.2 no.1
• /
• pp.61-67
• /
• 1998

In this paper, we have described the Ramp Activity Coordination Expert System (RACES) which can solve aircraft parking problems. RACES includes a knowledge-based scheduling problem which assigns every daily arriving and departing flight to the gates and remote spots with the domain specific knowledge and heuristics acquired from human experts. RACES processes complex scheduling problem such as dynamic inter-relations among the characteristics of remote spots/gates and aircraft with various other constraints, for example, custome and ground handling factors at an airport. By user-driven modeling for end users and knowledge-driven near optimal scheduling acquired from human experts, RACES can produce parking schedules of aircraft in about 20 seconds for about 400 daily flights, whereas it normally takes about 4 to 5 hours by human experts. Scheduling results in the form of Gantt charts produced by the RACES are also accepted by the domain experts. RACES is also designed to deal with the partial adjustment of the schedule when unexpected events occur. After daily scheduling is completed, the messages for aircraft changes and delay messages are reflected and updated into the schedule according to the knowledge of the domain experts. By analyzing the knowledge model of the domain expert, the reactive scheduling steps are effectively represented as rules and the scenarios of the Graphic User Interfaces (GUI) are designed. Since the modification of the aircraft dispositions such as aircraft changes and cancellations of flights are reflected to the current schedule, the modification should be notified to RACES from the mainframe for the reactive scheduling. The adjustments of the schedule are made semi-automatically by RACES since there are many irregularities in dealing with the partial rescheduling.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.2
• /
• pp.152-161
• /
• 2019

This research carried out a study on the job characteristics of the skipper of the coastal composite fishing vessels in order to find a way to prevent the ship collision caused by the highest human error among the marine casualty of fishing boats. Video observation was used as the research method in which six CCD cameras were installed on the vessel to collect image data and data extracted from the image were analyzed to derive the results of the functional activity of skipper according to the fishing operation process of experimental fishing vessel. The results are as follows. The working process of the experimental fishing vessel consisted of navigation for fishing ground, setting line, waiting for hauling line, hauling line and navigation to homeport. In these processes, the skipper was performing watchkeeping in the wheelhouse in which he carried out a single task, a dual task that performed two tasks simultaneously, and a triple task that performed two or more tasks simultaneously. In addition, one of the risk factors causing the collision was a no watchkeeping in the wheelhouse for navigating for fishing ground, waiting for hauling line, and hauling line at 25.4%, 64.6% and 0.3%, respectively among the marine casualty while drowsiness caused 1.2% of the marine casualty in navigating for fishing ground. Concurrent tasks that simultaneously perform two or more tasks that can overlook any other important duties while carrying out watchkeeping in the wheelhouse include 51.3% of navigation for fishing ground, 81.9% of setting line, 19.0% of waiting for hauling line, 87.9% of hauling, and 88.7% of navigation to homeport. The above concurrent tasks yielded an average of 66.1%. Experimental fishing vessels are required to focus on ship handling operations related to fishery operations, and the skipper is assigned more activities and attention to fishery related tasks. Therefore, it is considered desirable to build a collision prevention system that is appropriate to the characteristics of the skipper's work, escaping from transferring the responsibility of ship collision to the skipper completely.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.593-596
• /
• 2005

The MSC is a remote sensing instrument with very high performance that is to be installed on KOMPSAT2 satellite. The MSC consists of EOS (Electro-Optic Subsystem), PMU (Payload Management Unit) and PDTS (Payload Data Transmission Subsystem). PMU controls and monitors all the other payload units by sending commands and collecting telemetry. PMU is in charge of interfacing between payload system and satellite bus system. PMU gets commands from ground-station via OBC (On-Board Computer) that is a main controller of the satellite bus system and sends telemetry to the ground-station via OBC. There is a processor module, called SBC (Single Board Computer) in the PMU. The SBC is a main controller of the MSC system. The main roles of the SBC are payload mission management, command validation and execution, telemetry collection and monitoring, ancillary data handling, event reporting, power control of payload sub-units and communication with these units. Intel's 80486DX2 processor has been used for the SBC. Due to the fact that the SBC plays important roles for imaging mission execution and handles a lot of control data that is required for payload operation, it is required to make analysis of the CPU load when it is in maximum operation mode. In this paper, the analysis and measurement results of the SBC throughput in the maximum operation mode.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.4
• /
• pp.397-408
• /
• 2007

Diplexer is one of core devices needed to communicate with satellite using single ground antenna by separating uplink and downlink signal. This paper presents the design of the S-band diplexer for LEO TT&C application, especially for KOMPSAT (KOrea Multi-Purpose SATellite). To cope with requirements such as high handling power, low insertion loss, air-cavity resonator with high quality factor was considered as one of design drivers. Design was started with predicting unloaded Q and equivalent circuit from the structure of air-cavity resonator. For the convenience of adjustment, the coupling factor placed between resonators was estimated from COTSEM (Electro-Magnetic) simulator, EESOF $ADS^{TM}$, and expressed with 2-order polynomial regression. To improve the isolation between transmitting part (Tx) and receiving part (Rx), the inductive and capacitive attenuation poles were inserted between $4^{th}\;and\;6^{th}$ resonator respectively. The fabricated diplexer consists of two bandpass filters and each filter has eight resonants. From the measurement, it was shown that major requirements such as 0.5dB of insertion loss, 20dB of return loss and 100dB of isolation were fully satisfied within passband.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.11 no.2
• /
• pp.101-106
• /
• 1993

This study is a efficient management techniques of road by facility database. The purpose of road ledger investigate the property of road facility, the present condition of the location, the quality of the material of the ground and underground facility. Also, this is used to make plan for construction, and investment program of the road. To build road database, photogrammetry, ground control surveying and aerial photogrammetry must be performed. After the research of the road facility, a underground facility map and the road drawings are to be made. In this study, model area is the KUMJUNG-KU in Pusan where an industrial road is located on. There are about 7,000 signal lampes and traffic safety boards. It is possible to manage scientifical and efficient road ledger though statistical handling using facility database. In this paper, authors found the database of road facility through basic circumstances in the use of SML of ARC/INFO.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.183-188
• /
• 2008

Engine control/performance model for helicopter simulator is one of the most important models which affect flight performance and handling quality. It is typical to develop the model based on the raw data and models from the engine designers/manufacturers. The approaches in this study were to develop the basic model based on the available resources and to tune and verify it based on the ground/flight test results. The maintenance manuals of TB3-117 which is installed in KA-32T were reviewed and the components to be simulated for the engine control model were categorized and modeled. Piece-wise linear modeling method was used for the engine performance model. The engine performance data in the engine maintenance manuals were incorporated into the engine steady state performance tables, which were incorporated with the transfer functions for the dynamic performance. Engine control/performance model was compared and tuned with the ground/flight test results. It was verified that the fidelity of the model was within the tolerances in FAA AC120-63.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.8
• /
• pp.50-55
• /
• 2005

An advanced method of Relaxed Static Stability (RSS) is utilized for improving the aerodynamic performance of modern version supersonic jet fighter aircraft. The laws of flight control system utilize RSS criteria in both longitudinal and lateral-directional axes to achieve performance enhancements. Particularly, the design of longitudinal control laws for utilizing RSS methods greatly affects the performance of the aircraft in Air-to-Air Tracking and Air-to-Ground modes, which improves weapon delivery. In the area of Air-to-Air Tracking, the development of longitudinal control laws aids in the fine tracking and gross acquisition of other aircraft. This paper proposes that new concept of longitudinal control law introduce in order to improve fine tracking performance in air-to-air tracking maneuver. Result of HQS pilot simulation and flight test, fine tracking performance improve without degradation of gross acquisition when new concept of control law is applied.

• Geophysics and Geophysical Exploration
• /
• v.6 no.4
• /
• pp.195-198
• /
• 2003

In this study, we have developed a 3-D visualization program that is helpful in the interpretation or comparisons of geologic and geophysical data, which have been acquired to understand the cause of ground subsidence in the residential area and to establish reinforcement strategy. The visualization program was developed under the Windows operating system for convenient use and easy understanding. It uses Visual C++ for the Graphic User Interface and the OpenGL for graphic handling. Since this program is user-friendly, even users who do not have the basic idea about GIS or CAD can get very useful information with this program. The applicability of the program has been verified by visualizing the real core log and resistivity tomography images obtained from the ground subsidence area. These results have shown that the program is very useful for comparisons of these two data for the interpretation of subsurface structures.

• Journal of KIBIM
• /
• v.6 no.4
• /
• pp.27-34
• /
• 2016

A Building Information Model (BIM) is an attempt to simulate the process of building structures in a three-dimensional (3D) digital space. While the technology is usually applied to structured buildings, bridges, and underground facilities, it is rarely applied to an unstructured environment of earthwork operations. If a BIM is used for earthworks, the 3D simulation can be used for construction equipment guidance and earthwork management. This paper presents a real-time, 3D earthwork BIM that provides a 3D graphical simulation of excavators in conjunction with geographic modeling. Developing a real-time, 3D earthwork BIM requires handling a variety of factors, such as geographical information and vehicular movement. This paper mainly focuses on the management of these attributes and provides a database design for storing and retrieving data. In an example application, a prototype of the 3D earthwork BIM is presented to understand what it would provide when used during earthwork operations at a construction site.