• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.26-31
• /
• 2001

In order to measure the distance from the bottom in the ocean we use ultrasound altitude sonars. The manganese nodule pick-up device developed by KRISO is also using an altitude sonar to control the gap between the pick-up head and sea bottom. This paper describes the performance of the altitude sonar by an experimental method. The experiment was performed with four ground models in a small basin, Manganese nodule models and water-bentonite mixture was used for setting up the ground models. Buttorworth filter was applied to remove the noise caused by a servo motor and its controller. The results show that the altitude sonar gives a good estimation of the types and slopes of the bottom as well as the distance.

• New & Renewable Energy
• /
• v.7 no.2
• /
• pp.36-42
• /
• 2011

The wind speed at the altitude around 300 m is much higher and less variable than at the altitude around 80 m which is the same height of the MW class tower turbine's hub height. The wind power density is increased 0.37 W/$m^2$ per meter at the altitude around 6 to 7 km and 0.25 W/$m^2$ per meter at the altitude around 80 to 500 m. There are two types of power generation systems using lifting bodies. The one is that The generator is installed in the ground station and stretched into the lifting body through the tether. The other is that the generator is installed in the lifting body and stretched into the ground station through the tether. Many kinds of lifting bodies are also researched in the world, called kites, wings, single or twin aerostat, and so on. This article introduced the technical development status and the market prospects of the high altitude wind power generation system all over the world in detail.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.749-756
• /
• 2013

This paper presents an algorithm concerning the ground altitude measurement using a laser altimeter and an ultrasonic rangefinder for UAV(Unmanned Aerial Vehicle). A simple ground test conducted using the laser altimeter and ultrasonic rangefinder that are used for conducting the low altitude measurement of UAV and identify the characteristics of each sensor. Especially, the disadvantages of the laser altimeter were checked through the ground test. After that who those are participated in this paper planned the algorithm which is complemented by the ultrasonic rangefinder and the experiment was conducted. The laser altimeter and the ultrasonic rangefinder were fused by a loosely coupled method by Kalman filter. The paper shows that stable value of altitude complemented by the ultrasonic rangefinder that covers the laser altimeter's drawbacks can be measured through the ground test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.1
• /
• pp.54-60
• /
• 2013

This paper presents a ground altitude determination algorithm using a laser altimeter and GPS for automatic take-off and landing of UAV. The characteristics of the laser altimeter was analyzed in ground tests and a low-pass filter was designed to reduce the effect of signal interruption due to reflectivity problem. The paper shows that a single sensor cannot measure ground altitude appropriately in terms of reliability and accuracy. To complement shortcomings of the laser altimeter, the linear Kalman filter was designed using DGPS vertical speed. Designed filter was validated and tuned through the steps of simulation, ground test and flight test. It was confirmed that the accuracy for automatic landing is achievable.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.104-111
• /
• 2005

Gas turbine engines for aircraft are usually operated at the altitude condition which is quite different from the ground condition. In order to measure the precise performance data at the altitude condition, the engine should be tested at the altitude condition by a real flight test or an altitude simulation test with an altitude test facility. In this paper, the present state of the altitude test facility and the test technologies at urn(Korea Aerospace Research Institute) will be introduced.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.112-115
• /
• 2017

We analyzed the rocket engine flow to check whether the possibility of the ground test and the equipment safety problems in the high altitude engine test facility. The test condition is that the vacuum chamber is open and the coolant water is injected into the supersonic diffuser. The analysis uses two-dimensional axisymmetry with a mixture of plume, air, and cooling water. As a result, the ground test was possible up to the cooling water flow rate of 200 kg/sec. However, due to the back flow of the initial plume, the vacuum chamber is exposed to high temperature, and at the same time, the inside of the vacuum chamber is contaminated due to the reverse flow of the cooling water. Therefore, sufficient insulation measures and work for pollution avoidance should be preceded.

• Journal of Astronomy and Space Sciences
• /
• v.40 no.1
• /
• pp.35-44
• /
• 2023

Surveillance and reconnaissance intelligence in the space domain will become increasingly important in future battlefield environments. Moreover, to assimilate the military provocations and trends of hostile countries, imagery intelligence of the highest possible resolution is required. There are many methods for improving the resolution of optical satellites when observing the ground, such as designing satellite optical systems with a larger diameter and lowering the operating altitude. In this paper, we propose a method for improving ground observation resolution by using an optical system for a previously designed low orbit satellite and lowering the operating altitude of the satellite. When the altitude of a satellite is reduced in a circular orbit, a large amount of thrust fuel is required to maintain altitude because the satellite's altitude can decrease rapidly due to atmospheric drag. However, by using the critical inclination, which can fix the position of the perigee in an elliptical orbit to the observation area, the operating altitude of the satellite can be reduced using less fuel compared to a circular orbit. This method makes it possible to obtain a similar observational resolution of a medium-sized satellite with the same weight and volume as a small satellite. In addition, this method has the advantage of reducing development and launch costs to that of a small-sized satellite. As a result, we designed an elliptical orbit. The perigee of the orbit is 300 km, the apogee is 8,366.52 km, and the critical inclination is 116.56°. This orbit remains at its lowest altitude to the Korean peninsula constantly with much less orbit maintenance fuel compared to the 300 km circular orbit.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.2
• /
• pp.127-134
• /
• 2006

Variation of the Local Time of Ascending Node (LTAN) has been analysed according to initial inclinations when the altitude of Sun-synchronous satellite is continuously decreased due to the atmospheric drag. Orbit predictions of 3 years have been performed with the satellite of 500 km altitude when the initial LTAN were set to 06:00, 09:00, 12:00, 15:00, and 18:00. Different profiles of the inclination and LTAN have been obtained according to the satellite altitude decay and initial LTAN value. Using the profiles of the inclination and LTAN, initial orbital elements can be derived for minimizing the LTAN variations during the mission life time of the sun-synchronous satellite without any on-board thrusters for orbit maneuvers.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.173-181
• /
• 2008

Gas turbine engine for aircraft are usually operated at the altitude condition which is quite different from the ground condition. In order to measure the precise performance data at the altitude condition, the engine should be tested at the altitude condition by a real flight test or an altitude simulation test with an altitude test facility. In this paper describes the design of altitude test facility for turbo shaft engine. This facility will be located in test cell #2 at the Korea Aerospace Research Institute. Test Cell #2 will be used for altitude testing engines with mass flow rate up to 40kg/s and inlet temperatures in the range from $-65^{\circ}C$ to $200^{\circ}C$. The existing compressor/exhauster station with heater & cooler system will be used to simulate altitude conditions in Test Cell #2.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.3
• /
• pp.246-253
• /
• 2005

An experimenal study on flight control of high-speed AEV(Aero-levitation Electric Vehicle) scale model in wind-tunnel is conducted. The AEV is to fly at very low altitude in predesigned track so that it is always under the wing-in-ground effect. The experiment is intended to fly the scale model to follow the predesigned altitude schedule while holding its attitude (pitch, roll, and yaw). Especially, the altitude changes for climb, cruise, and descent with constant pitch angle are most important maneuvers. The experiment shows that the required mission flights can be performed with appropriate sensors, processors, and actuators.