• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.385-394
• /
• 2007

In this study, the effect of molding condition on the tensile properties for plain woven hemp fiber reinforced green composite was examined. The tensile properties of the composite were compared with those of the plain woven jute fiber composite fabricated by the same process. Emulsion type biodegradable resin or polypropylene sheet was used as matrix. The composites were processed by the compression molding where the molding temperature and its heating time were changed from 160 to $190^{\circ}C$ and from 15 to 25 min, respectively. The following results were obtained from the experiment. The tensile property of hemp fiber reinforced polypropylene is improved in comparison with polypropylene bulk. The strength of composite is about 2.6 times that of the resin bulk specimen. Hemp fiber is more effective than jute fiber as reinforcement for green composite from the viewpoint of strength. The molding temperature and time are suitable below $180^{\circ}C$ and 20 min for hemp fiber reinforced green composite. Hemp fiber green composite has a tendency to decrease its tensile strength when fiber content is over 50 wt%.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.6
• /
• pp.34-43
• /
• 2010

Recently environmental regulations like the Kyoto Protocol, adopted in 1997, required the reduction of the greenhouse gas of 5.2% up to 1990 regulations. and 13th General Assembly in 2007, held in Bali of India, have agreed to duty reduction even in developing countries in 2013. Because of the lack of information about real process in small or middle size industries, most recent research omitted to calculate green house gas emissions from the industrial process. Bottom-up methodology will be applied for calculation of green house gasemission from industry sector to solve these problems in this research. Total amount from industry sector of Shicheung-City in 2007 was about 1,797,305 tons of greenhouse gas $CO_2$ and 3,049,403 tons of the greenhouse gas $CO_2$ calculated from industry sector of Ansan-City in 2007.

• Journal of electromagnetic engineering and science
• /
• v.7 no.2
• /
• pp.59-63
• /
• 2007

This paper suggests a novel method to efficiently calculate the spatial-domain Green's functions of 2D electromagnetic problems Briefly speaking, this method combines spectral and spatial domain calculation schemes and prevents the Green's functions from poor convergence due to the singularities that complicate the process of the Method of Moment(MoM) applications For the validation of this proposed method, fields will be evaluated along the spatial distance including zero distance for 2D free-space and periodic homogeneous geometry The numerical results show the validity of the prosed method and correspondng physics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.5
• /
• pp.494-499
• /
• 2023

In this paper, in order to apply the CF (color filter) type of the micro light emitting device (Micro LED) display method, a study on the manufacturing process of red and green phosphor inks for the inkjet process was conducted. The blue light-emitting KSF and LuAG phosphors were respectively used to control the phosphor particle size to about 1㎛, and a phosphor ink was prepared by synthesizing with a low-viscosity solution (IPA/Eg). A chemical dispersion method was applied to selectively control the dispersion characteristics in the manufacture of phosphor inks, and in particular, phosphor inks with a dispersant applied a dispersant secured stable dispersion characteristic compared to phosphor inks without a dispersion process. Therefore, it seems possible to manufacture CF for Micro LED through an inkjet process capable of controlling the dispersion characteristics of phosphor ink.

• Journal of Energy Engineering
• /
• v.29 no.3
• /
• pp.50-56
• /
• 2020

Currently, 3D printing technology is a new revolutionary additive manufacturing process that can be used for making three dimensional solid objects from digital films. In 2019, this 3D printing technology spreading vigorously in production parts (57%), bridge production (39%), tooling, fixtures, jigs (37%), repair, and maintenance (38%). The applications of 3D printing are expanding to the defense, aerospace, medical field, and automobile industry. The raw materials are playing a key role in 3D printing. Various additive materials such as plastics, polymers, resins, steel, and metals are used for 3D printing to create a variety of designs. The main advantage of the green cement for 3D printing is to enhance the mechanical properties, and durability to meet the high-quality material using in construction. There are several advantages with 3D printing is a limited waste generation, eco-friendly process, economy, 20 times faster, and less time-consuming. This research article reveals that the role of green cement as an additive material for 3D printing.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.1
• /
• pp.14-20
• /
• 2016

This paper describes a green stripping process to effectively strip the remaining DFR layer on a non-alkali-based ITO glass surface after an etching process. A stripper, water-soluble amine compound, is used to investigate the characteristics of stripping ability and to suggest a valid method for the green process. Increasing the composition (5-30% concentration) of the ethanol amine-based stripper was found to greatly reduce the stripping time applied in the dipping method. The composition (30%) achieved an excellent stripping effect and free-residue impurities. Additionally, it was possible to obtain the effect of stripping in a way to sustain the release before generating DFR sludge from the ITO glass surface by using dipping condition (stripping time) in the composition. An Additional stripping process (buffering) out of dipping can realize productivity improvement and cost reduction because of the higher proportion of re-use of the stripping solution used in the DFR removal step.

• Natural Product Sciences
• /
• v.25 no.2
• /
• pp.150-156
• /
• 2019

Conventional extraction of oil and azadirachtin, a botanical insecticide, from Azadirachta indica involves defatting the seeds and leaves using hexane followed by azadirachtin extraction with a polar solvent. In order to simplify the process while maintaining the yield we explored a binary extraction approach using Soxhlet extraction device and hexane and ethanol as non-polar and polar solvents at various ratios and extraction times. The highest oil and azadirachtin yields were obtained at 6 h extraction time using a 50:50 solvent mixture for both neem leaves (44.7 wt%, $720mg_{Aza}/kg_{leaves}$) and seeds (53.5 wt%, $1045mg_{Aza}/kg_{leaves}$), respectively.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.25-33
• /
• 2022

This study developed the black liquor evaporation process models using the multiple-effect-evaporator according to the number of effects to predict steam consumption. The developed models were divided into the black liquor preheating and evaporation processes, and a virtual reboiler was added to predict steam consumption. In simulation results, the steam consumption in the double-effect-evaporator was decreased by 48.9 %, and as the number of effects increased, the steam consumption was decreased. Finally, the steam consumption in the octuple-effect-evaporator was decreased by 61.2 %. Also, this study suggests a strategy for deriving the optimal number of effects in the process by analyzing the latent heat recovered from the saturated vapor produced in the multiple-effect-evaporator and the amount of saturated vapor produced by each effect.

• Korean Journal of Materials Research
• /
• v.11 no.10
• /
• pp.869-878
• /
• 2001

Alumina $(Al_2O_3)$ green bodies were fabricated by gel-casting using three kinds of alumina with different particle size (mean particle size: 4.6 $\mu\textrm{m}$, 0.32 $\mu\textrm{m}$, 10nm). The effects of particle size on gel-casting process and green microstructure were investigated. The optimum dispersion conditions using ammonium salt (D-3019) as dispersant were 0.2 wt% (4.63 $\mu\textrm{m}$), 0.5 wt% (0.32 $\mu\textrm{m}$), and 5.0 wt% (10 nm), in high solid loading. The optimum solid loading of each starting material for gel-casting was obtained as 59 vol% (4.63 $\mu\textrm{m}$), 57 vol% (0.32 $\mu\textrm{m}$), 15 vol% (10 nm), depending on particle size, indicating that nano-size particle (10 nm) represent lower solid loading as high specific surface area than those of other two starting materials. The drying at ambient conditions (humidity; $\thickapprox$90%) was performed more than 48hrs to enable ejection of the part from the mold and then at $120^{\circ}C$ for 2hrs in an air oven, showing no crack and flaw in the dried green bodies. The pore size and distribution of the gelcast green bodies showed the significant decrease with decreasing particle size. Green microstructure was dependent on the pore size and distribution due to the particle size, and on the deairing step. The green density maximum obtained was 58.9% (4.63 $\mu\textrm{m}$), 60% (0.32 $\mu\textrm{m}$), 47% (10 nm) theoretical density (TD), and the deairing step applied before gel-casting did not affect green density.

• Korean Journal of Construction Engineering and Management
• /
• v.18 no.2
• /
• pp.3-11
• /
• 2017

Aging buildings over 15 years reaches about 74% of 177 thousand buildings in Domestic public buildings. Due to the aging building, the energy loss is a serious problem. In order to reduce the energy usage through improving the energy efficiency on the existing buildings, the government & the local autonomous entity conduct the energy efficiency projects through the remodeling, repairing & equipment replacement on the existing buildings. The green remodeling is applied to the existing public buildings in recently revised the act on the creation and support of green building. However, the standard is not obvious that the work scope of green remodeling, financing and project delivery method. This paper propose is to suggest project delivery system for vitalizing the green remodeling. Green remodeling is defined on basis of the occurring work under project life cycle based on the existing building process and the financing method for owners and companies and the project delivery system according to work scope of green remodeling are proposed in this paper