• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.191-198
• /
• 2000

Laser direct patterning of the coated photoresist (PMER-NSG31B) layer was studied to make halftone dots on gravure printing roll. The selective laser hardening of photoresist by Ar-ion laser(wavelength: 333.6~363.8nm) was controlled by the A/O modulator. The coating thickness in the range of 5~11$\mu m$ could be obtained by using the up-down directional moving device along the vertically located roll. The width, thickness and hardness of the hardened lines formed under the laser power of 200~260㎽ and irradiation time of 4.4~6.6 $\mu$sec/point were investigated after developing. The hardened width increased as the coating thickness increased. Though the hardened thickness was changed due to the effect of the developing solution, the hardened layer showed good resistance to the scratching of 2H pencil. Also, the hardened minimum line widths of 10$\mu m$ could be obtained. The change of line width was also found after etching, and the minimum line widths of 6$\mu m$ could be obtained. The hardened lines showed the good resistance to the etching solution. Finally, the experimental data could be applied to make gravure halftone dots using the developed imaging process, successfully.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.163-164
• /
• 2013

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.969-974
• /
• 2014

Previously fabricated electronic devices were used for vacuum manufacturing processes such as conventional semiconductor manufacturing. However, they are difficult to apply to continuous processes such as roll-to-roll printing, which results in very high device manufacturing and processing costs. Therefore, many developers have been interested in applying continuous processes to contact printing or noncontact printing technologies and they proposed various continuous printing techniques instead of conventional batch coating. In this paper, we proposed improved gravure offset printing process as one of the contact printing technique. We used etching pattern geometry with soft core blanket roll for printing of ultra fine line below the 10um.Using this technique we obtained flexible metal grid mesh film as transparent conductive film.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.633-639
• /
• 1995

Dropouts in magnetic media are a primary quality deficiency which is detrimental to magnetic signal quality and thus the major impediment to error-free recording, especially in high density digital recorders. The specific form of defects and causes found to be responsible for signal dropouts occurring in magnetic tape were studied. Dropout occurred when the RF signal falls to low level due to the various types of surface defects. However, the fall in the level of the RF signal in gravure roll coated tapes was most often caused by foreign particles adhering to the magnetic tape. It was also shown from the present study that scattered particles trapped under the tape surface or put on the top can lift it as it crosses the head, creating a spherical tent shaped defect and causing a temporary signal drop. Dropout producing substances were identified through optical and microchemical analyses. The results were correlated with measured electrical signal losses combined with analytical microscopy to clarify source identification of defects.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.461-466
• /
• 2007

There has been a great interest in printing technology as a low cost and mass production method for the application of printed electronics such as printed TFT, solar cell, RFID Tag, printed battery, and so on. In this study, apparatuses of gravure-offset printing are developed for fine line-width/gap printing and examining pattern distortion occurred in gravure-offset printing process. The fine line-width/gap pattern shows that it is possible to make around 20 micro-meter line-width/gap printing patterns. Pattern distortion is modeled, and the amount and shape of the distortion are calculated by using commercial FEM code. The roll-to-roll printing system under development consists of unwinder/rewinder, two printing units, one coating unit, drying units, guiding unit, vision system, and other auxiliary devices. For multi-layer printing, the system is designed to be capable of printing two different materials.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.267-272
• /
• 2017

Automotive seat covers with olefin film imported from foreign companies exhibit some problems such as low peeling strength and high burning rate. The traditional manufacturing process requires gas flame or direct heating for the laminating step. This paper introduces an alternative solution that replaces the olefin film and flame lamination method in making automotive seat covers or interior fabrics. We adopt a new manufacturing concept that applies a water-based resin coating to develop a coating system. The coating machine was successfully developed and tested. Results are intended to contribute to improving the quality and productivity of automotive seat cover production.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.12 no.1
• /
• pp.1.1-11
• /
• 1994

The photosensitive properties and carrier transport in the organic photoconductor with the carrier transport layers(CTL) of polymer matrix doped with two carrier transport materials above carrier generation layer(CGL) containing oxotitanium phthalocyanine (TiOPc) were investigated. The CGL of TiOPc dispersed in poly(vinylbutyral) was formed as thickness of 0.1${\mu}{\textrm}{m}$and the carrier transport layer was prepared by coating polycarbonate and polyester doped with oxadiazoly(OXD), polyvinylcarbazole (PVK), trinitro fluorenone(TNF) as thickness of 10~15${\mu}{\textrm}{m}$, respectively. We have measured half decay exposure,sensitivity and xerographic gain from the photo-induced discharge curve(PIDC). In this work, it was found that the characteristics of carrier transport were mainly caused by the ionization potential difference of constitutive materials in molecularly doped polymer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.813-820
• /
• 2015

We have studied commercialization and process optimization of protective film on transparent conductive coated substrate, nano silver on flexible PET (poly ethylene terephthalate), by means of roll-to-roll micro-gravure coater. Nanosilver on flexible PET substrate is potential materials to replace ITO (indium tin oxide). Protective film is most important to maintain unique silver pattern on top of transparent PET. PSA pressure sensitive adhesives) was developed solely for nano silver on PET and protective film was successfully laminated. We have optimized all process conditions such as coating thickness, line speed and aging time & temperature via experimental design. Transparent conductive film and its protective film developed in this research are commercially available at this moment.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.589-595
• /
• 2013

Solution processed conjugated molecules enable to manufacture various electronic devices by unconventional and cost effective patterning methods as screen or gravure printing. Spin-coating is the most popularly used method to form conjugated polymeric film for various electronic devices. The coating method has certain disadvantages such as a large amount of unwanted wastes, difficulty forming a film with a large area, and impossible to apply roll-to-roll manufacturing. We present here a promising alternative coating method, bar-coating for conjugated polymer film and OLED with the bar coated light emitting layer. In this papers, we show atomic force microscope images of spin- and bar-coated Poly[(9,9-di-n-octylfluorenyl-2,7-diyl)-alt-(benzo[2,1,3]thiadiazol-4,8-diyl)] (F8BT) films on substrate. The bar-coated film showed a slight lower RMS roughness (1.058 [nm]) than spin-coated film (1.767 [nm]). It means the bar-coating is suitable method to form light emitting layers in OLEDs. By using bar-coating process, an OLED obtained with 4.7 [cd/A] in maximum current efficiency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.36-42
• /
• 2024

Roll-to-roll processing holds an integral position within the manufacturing landscape, and its significance reverberates across numerous industries. This versatile technology platform encompasses a diverse array of process methods and accommodates a wide spectrum of material categories, making it a cornerstone of modern production. Within this expansive domain, two commonly employed coating techniques, namely the slot die and gravure coating methods, have earned their prominence for their precision and efficiency in delivering flawless coatings. Additionally, the realm of drying processes relies heavily on thermal drying, infrared (IR) drying, and ultraviolet (UV) drying methods to expedite the transformation of materials from their liquid or semi-liquid states to solid, ready-to-use products. The undeniable importance of roll-to-roll processing lies in its ability to streamline manufacturing processes, reduce costs, and enhance product quality. This article embarks on a comprehensive journey to fathom the depth of this importance by delving into the intricacies of these common roll-to-roll process methods. Through rigorous research and meticulous data collection, we aim to shed light on the pivotal role these techniques play in shaping various industries and advancing the world of manufacturing. By understanding their significance, we can harness the full potential of roll-to-roll processing and pave the way for innovation and excellence in production.