• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2010.04a
• /
• pp.429-431
• /
• 2010

The hybrid geoid model should be determined by fitting the gravimetric geoid to the geometric geoid which were presented the local vertical level. Therefore, it is necessary to find firstly the optimal scheme for improving the accuracy of gravimetric geoid in order to development the high-precision hybrid geoid model. Through finding the optimal scheme for determining the each part of gravimetric geoid, the most accurate gravimetric geoid model in Korea will be developed when the EIGEN-CG03C model to degree 360, 4-band spherical FFT and RTM reduction methods were used for determining the long, middle and short-frequency part of gravimetric geoid respectively. Finally, we developed the hybrid geoid model around Korea by correcting to gravimetric geoid with the correction term. The correction term is modelled using the difference between GPS/Levelling derived geoidal heights and gravimetric geoidal heights. The stochastic model used in the calculation of correction term is the LSC technique based on second-order Markov covariance function. 503 GPS/Levelling data were used to model the correction term. The degree of LSC fitting to the final hybrid geoid model in Korea was evaluated as 0.001m ${\pm}0.054m$.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.1
• /
• pp.9-12
• /
• 1994

The gravimetric determination of scandium by di-(2-ethylhexyl)phosphate(DEHPA) as a precipitant and the mole ratio of Sc-DEHPA arecipitation obtained in ethanol medium have been investigated. Scandium can be determined by gravimetric method of precipitation of Sc-DEHPA and the mole ratio of Sc-DEHPA is found as 1 :2 in ethanol medium.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2010.04a
• /
• pp.117-119
• /
• 2010

Geoid is the equi-gravity potential surface. Gravimetric geoidal heights could be determined by the gravity observation values and geometric geoidal heights could be determined by the GPS ellipsoidal heights at benchmark station. In this study, both gravimetric geoidal heights and geometric geoidal heights were determined and compared in mountainous area. For the study, GPS surveying and gravity observation were accomplished at 1st and 2nd order levelling network located in mountainous area in Kyungsanbukdo and Chollanamdo.

• Journal of Environmental Impact Assessment
• /
• v.19 no.4
• /
• pp.431-441
• /
• 2010

In this study, inter-comparison for PM-2.5 was undertaken. The PM-2.5 mass concentrations using the gravimetric and beta-attenuation methods were compared during the winter in 2007. Two different types of conventional filter-based measurements (Cyclone type and Impactor type) were also collocated and the measurement data was compared with each other. As a result, continuous PM-2.5 data using beta attenuation method show a comparable mass concentration with gravimetric measurement when the inlet of beta-gauge sampler is heated. The results also showed that the cyclone type shows a little high PM-2.5 concentration than Impactor type. In all the sampling cases, the correlations between measurement methods are high. Subsequently, this study suggests that highly correlated relationship between PM-2.5 measurement instruments can be obtained through the inter-comparison results based on filterb-ased gravimetric method and more intensive measurement and theoretical studies are needed in order to clarify the measurement errors for different sampler types.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.1
• /
• pp.59-64
• /
• 2017

Diverter is an essential element in gravimetric calibration method of flowmeter. Error of diverter are influenced by flow velocity profile of nozzle outlet, motion velocity of diverter and detecting location. That's why, time detection position of diverter is tuned through repetitive test for minimizing error of diverter. Further the diverter must be compared with the other institutions test since the influence on the accuracy of the flow meter used in the test. In this paper, errors (flow velocity profile of nozzle outlet, motion velocity of diverter and detecting location) of diverter are decreased by produced uni-direction diverter and error of gravimetric calibration system is decreased. Uni-direction diverter is calibrated by gravimetric calibration system with precision flowmeter, the flowmeter is calibrated by pipe prover and other institutions and uni-direction diverter is evaluated. Uni-direction diverter is not influenced by flow velocity profile of nozzle outlet, motion velocity of diverter and detecting location. As a result, Uni-direction diverter can calibrate in wider scope since increasing ratio of maximum and minimum flow rate of uni-direction diverter.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.276-281
• /
• 2013

Polyester type polyurethane foam modified with acrylic polyol was prepared by quasi prepolymer method. Thermal and dynamic mechanical properties of polyurethane foam were analysed by thermal gravimetric analysis(TGA) and dynamic mechanical analysis(DMA). Also, glass transition temperature was measured by differential scanning calorimeter(DSC). As acrylic polyol contents were increased, thermal stability measured by TGA was slightly decreased. Storage modulus was increased and tan delta was decreased with increasing of acrylic polyol contents.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.4
• /
• pp.561-571
• /
• 2001

The standard uncertainty of flowrate measurement is obtained by combining that of independent variables. Gravimetric and volumetric method were applied to determine the flowrate and the standard uncertainties of flowrate measurement by both methods were evaluated in accordance with the procedure recommended by International Organization for Standardization. The combined standard uncertainties of determining the flowrate were estimated from the sensitivity coefficient and the standard uncertainty of independent variables. For practical application, the methods for evaluating and expressing uncertainty in flow measurement were discussed. It was found that the uncertainties of the weighing and time measurement in gravimetric method, the volume and time measurement in volumetric method have dominant influence on that of flowrate measurement. With the quantitative analysis of the sensitivity coefficient, the contribution of the each variable uncertainty to the combined standard uncertainty of flowrate measurement is shown clearly.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.12 no.1
• /
• pp.61-68
• /
• 1994

Neglecting distant zones in the computation of geoidal heights using Stokes'formula give rise to some truncation errors. The GRS80 Korean Gravimetric geoid Model 1993(KGM93) of the South Korea region was implemented, in this paper, using a combination of satellite-derived GEM-T2 gravity and terrestrial gravity data. A spherical cap size of 30 degree is used on the integration and the truncation error is compensated to the free-air geoid. The results of this study show that the accuracy of the KGM93-C has one meter level.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2005.06a
• /
• pp.386-393
• /
• 2005

The calcination characteristic of waste eggshell were examined by thermal gravimetric analysis (TGA), qualitative and quantitative analysis by X-ray fluorescence, and microstructural analysis by scanning electronic microscopy(SEM). The calcined sample was lager grain and pore size.

• 한국지형공간정보학회:학술대회논문집
• /
• 2005.08a
• /
• pp.93-99
• /
• 2005

This paper summarizes a preliminary geoid computation for western Mongolia, utilizing the airborne data collected fall 2004, as part of the NGA-DNSC-ALAGaC-MonMap cooperative airborne gravity project. A gravimetric geoid has been computed using the airborne gravity data, SRTM terrain models and GRACE/EGM global fields. The gravimetric geoid has subsequently been fitted to GPS-leveling data across Western Mongolia, as well as for a special Ulaanbaatar city geoid model.