• Computers and Concrete
• /
• v.31 no.5
• /
• pp.443-455
• /
• 2023

This is a research analyses on the bearing capacity at a pile tip embedded in rock. The aim is to propose a shape coefficient for an analytical solution and to investigate the influence of the plastic flow law on the problem. For this purpose, the finite difference method is used to analyze the bearing capacity of various types and states of rock masses, assuming the Hoek & Brown failure criterion, by considering both plane strain and an axisymmetric model. Different geometrical configurations were adopted for this analysis. First, the axisymmetric numerical results were compared with those obtained from the plane strain analytical solution. Then the pile shape influence on the bearing capacity was studied. A shape factor is now proposed. Furthermore, an evaluation was done on the influence of the plastic flow law on the pile tip bearing capacity. Associative flow and non-associative flow with null dilatancy were considered, resulting in a proposed correlation. A total of 324 cases were simulated, performing a sensitivity analysis on the results and using the graphic output of vertical displacement and maximum principal stress to understand how the failure mechanism occurs in the numerical model.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.2
• /
• pp.251-255
• /
• 2015

Thermal deformation, such as bending and twisting, occurs among the polymer parts of air-conditioner indoor units because of repetitive temperature change during heating operation. In this study, a numerical method employing finite-element analysis to efficiently simulate the thermal deformation of an assembly is proposed. Firstly, the displacement of an actual assembly produced by thermal deformation was measured using a 3D optical measurement system. The measurement results indicated a general downward sag of the assembly, and the maximum displacement value was approximately 1 mm. The temperature distribution was measured using a thermographic camera, and the results were used as initial-temperature boundary conditions to perform temperature-displacement analysis. The simulation results agreed well with the measured data. To reduce the thermal deformation, the stiffness increased 100%. As the results, the maximum displacement decreased by approximately 5.4% and the twisting deformation of the holder improved significantly.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.20 no.4
• /
• pp.54-75
• /
• 1993

The purpose of this thesis is to suggest objective basic data for the super graphics in the urban landscape through the quantitative visual quality analysis. For this, the image structure of super graphics have been measured mainly by questionnaries and semantic differential scle method and analyzed by the method of factor analysis, means and multiple regression. Degree of visual preference have been measured mainly by questionnaries and likert attitude scale method and finaly these data have been analyzed by using the stepwise method. The data were collected by presenting 12 super graphics photographs-4 each sample pictures from the 3 each selected districts representing typical urban landscape style(central business district, shopping district, apartment complex). Observer groups were categorized as professionals, students, the others. Result of this thesis can be summarized as fallows: 1. From all 12(3${\times}$4) sample super graphics, the value of each semantic differential scale among the observer groups were presented significant group difference. But no significant difference of the S.D. scale value were observed among central business district, shopping district and apartment complex super graphics. 2. For all experimental points, 4 types of factor have been observed. Factors covering the image of super graphics were found to be the evaluation, the intimacy, the potentiality and the tidiness. 3. Main factors of the super graphics image and factors indicating the group variations yielded high significance between areas. 4. The harmony with surrounding environment, the proper selection of super graphics subject yielded high values for all groups. Especially, the good color sense with building was the most important variable determining the degree of visual preference. 5. The urban C.B.D. super graphics obtained 5∼12 ranks of regional visual preference and the shopping district super graphics obtained 2∼11 ranks, and apartment complex super graphics obtained 1∼7 ranks.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.3
• /
• pp.599-604
• /
• 2021

In an era where AI artificial intelligence converges into each field, design of AI-CARE function and UI UX design are in the spotlight. The application of shape design and the trend of color are important for visual effects to match new features. In this paper, we would like to use this to present an example of the arrangement and application of form trends and to present design directions. In the introduction, the latest design environmental factors were analyzed and studied in the direction of the new proposal. In the text, the design direction and consideration of the design in the planning were studied by separating the functional design form, and the direction of the design work was presented. At the stage of form and color, a plan was proposed to match the flow of minimalism, universal design, and affordance design. A study method based on case practice is a consideration of how to consider content on shapes and colors specialized in the partial design work, and proposed to enable graphic production of new areas of UI UX in content images to be feasible. Through this study, the design direction and planning of the derivative method of shape and color was reached by suggesting design directionality and validity for each AI CARE bed PART.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.183-186
• /
• 2007

Realistic deformation of computer simulated anatomical structures is computationally intensive. As a result, simple methodologies not based in continuum mechanics have been employed for achieving real time deformation of virtual reality. Since the graphical interpolations and simple spring models commonly used in these simulations are not based on the biomechanical properties of tissue structures, these "quick and dirty"methods typically do not accurately represent the complex deformations and force-feedback interactions that can take place during surgery. Finite Element(FE) analysis is widely regarded as the most appropriate alternative to these methods. However, because of the highly computational nature of the FE method, its direct application to real time force feedback and visualization of tissue deformation has not been practical for most simulations. If the mathematics are optimized through pre-processing to yield only the information essential to the simulation task run-time computation requirements can be drastically reduced. To apply the FEM, We examined a various in verse matrix method and a deformed material model is produced and then the graphic deformation with this model is able to force. As our simulation program is reduced by the real-time calculation and simplification because the purpose of this system is to transact in the real time.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.28 no.2
• /
• pp.93-101
• /
• 2024

Code-compliant seismic design should be essentially applied to realize the so-called emulative performance of precast concrete (PC) lateral force-resisting systems, and this study developed simple procedures to design precast industrial buildings with intermediate precast bearing wall systems considering both the effect of seismic and blast loads. Seismic design provisions specified in ACI 318 and ASCE 7 can be directly adopted, for which the so-called 1.5S_y condition is addressed in PC wall-to-wall and wall-to-base connections. Various coupling options were considered and addressed in the seismic design of wall-to-wall connections for the longitudinal and transverse design directions to secure optimized performance and better economic feasibility. On the other hand, two possible methods were adopted in blast analysis: 1) Equivalent static analysis (ESA) based on the simplified graphic method and 2) Incremental dynamic time-history analysis (IDTHA). The ESA is physically austere to use in practice for a typical industrial PC-bearing wall system. Still, it showed an overestimating trend in terms of the lateral deformation. The coupling action between precast wall segments appears to be inevitably required due to substantially large blast loads compared to seismic loads with increasing blast risk levels. Even with the coupled-precast shear walls, the design outcome obtained from the ESA method might not be entirely satisfactory to the drift criteria presented by the ASCE Blast Design Manual. This drawback can be overcome by addressing the IDTHA method, where all the design criteria were fully satisfied with precast shear walls' non-coupling and group-coupling strength, where each individual or grouped shear fence was designed to possess 1.5S_y for the seismic design.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.176-185
• /
• 1996

Transformin the huge size of drawings into a suitable format for CAD system and recognizng the contents of drawings are the major concerans in the automated analysis of engineering drawings. This paper proposes some methods for text/graphics separation, symbol extraction, vectorization and symbol recognition with the object of applying them to electronic cirucit drawings. We use MBR (Minimum bounding rectangle) and size of isolated region on the drawings for separating text and graphic regions. Characteristics parameters such as the number of pixels, the length of circular constant and the degree of round shape are used for extracting loop symbols and geometric structures for non-loop symbols. To recognize symbols, nearest netighbor between FD (foruier descriptor) of extractd symbols and these of classification reference symbols is used. Experimental results show that the proposed method can generate compact vector representation of extracted symbols and perform the scale change and rotation of extracted symbol using symbol vectorization. Also we achieve an efficient searching of circuit drawings.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.68-76
• /
• 1989

In this paper, the influence of ram-pressure on the static and dynamic characteristics of infinite width tilting-pad journal bearing is investigated theoretically. The ram-pressure is obtained by assumption of conservation of mechanical energy of the lubricant flow through the leading edge of the pad. The pressure in the lubricating film is numerically calculated using the ram-pressure obtained as the inlet pressure boundary condition of the pad. The static equilibrium state of tilting-pad journal bearing is determined by Newton-Raphson iteration method. A numerical results are presented in graphic form and relationships between the ram-pressure and the static and dynamic characteristics are discussed.

• Proceedings of the Korean Society of Rural Planning Conference
• /
• 1998.03a
• /
• pp.15-16
• /
• 1998

It was studied Horticultural field by ARC/lNFO software, applicated on GIS- management information system, which dealt with graphic and attribute data together. This result obtained was summarized as follow : 1. It would be to output about position, attribute and photographic data of this horticultural farm through AML. 2. It would be easy to use with internal interface which is composed in basic function menu and application menu. 3. It would be good to plant Water melon and Tomato in this Horticultural farm. 4. The method which applicated overlay and analysis would be need to manage farming data in this horticultural farm and to develop a dynamic decision support system interfaced with GIS.

• Journal of East-West Nursing Research
• /
• v.11 no.1
• /
• pp.42-50
• /
• 2005

Purpose: The purpose this research was to provide with basic data in the control of the fatiguer found in the patients with fibromyalgia by analysing the factors that predict that. Method: At three university medical center, appointed 245 out-patients diagnosed of fibromyalgia according to the conditions by American College of Rheumatology (1990). The research instruments used in this study were graphic rating scale(Anxiety, sleep disturbance, pain, joint stiffness and depression), physical activity, the number of tender points, life satisfaction and Self-efficacy scale. In data analysis, SPSS 12.0 program was utilized and data were analyzed using descriptive statistics, Pearson's correlation coefficient and multiple regression. Result: The factors that predict the fatigue of patients with fibromyalgia were sleep disturbance, life satisfaction, pain, joint stiffness, illness duration, and anxiety which explained 50.1% of the fatigue. Conclusion: It has been confirmed that the regression equation model of this research may serve as a fatigue prediction factors in patients with fibromyalgia.