• Journal of Surface Science and Engineering
• /
• v.48 no.6
• /
• pp.329-334
• /
• 2015

The aim of this paper is to determine the proper heat treatment temperature for SDSS tube production without ${\sigma}$-phase precipitation. When Mother steel tube was heat treated at $800^{\circ}C$ temperature, relatively a large amount of ${\sigma}$-phase precipitated and grain refinement of ferrite phase occurred simultaneously. However, in Pilgered and Drawn steel tubes, grain refinement of the ferrite phase did not occur and a small amount of ${\sigma}$-phase precipitated. For all three types of steel tubes, the pitting potential was reduced to 2/5 or less compared with the untreated one and corrosion also occurred in the salt spray test due to the precipitation of ${\sigma}$-phase. When heat treatment temperature was $900^{\circ}C$, grain refinement of the ferrite phase occurred and very little ${\sigma}$-phase precipitated in Pilgered and Drawn steel tubes. But when heat treatment was done at $1,000^{\circ}C$ temperature, all three types of steel tubes had a similar corrosion properties of that of untreated one and also corrosion did not occur in the salt spray test, as ${\sigma}$-phase did not precipitate. Therefore, the optimum heat treatment temperature range is determined to be more than $1000^{\circ}C$ for the SDSS at which corrosion does not occur.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.6
• /
• pp.433-439
• /
• 2011

Poly Si TFTs (poly silicon thin film transistors) with p channel those are annealed HT (high temperature) with gate poly crystalline silicon and LT (low temperature) with metal gate electrode were fabricated on quartz substrate using the analyzed data and compared according to the activated grade silicon thin films and the size of device channel. The electrical characteristics of HT poly-Si TFTs increased those are the on current, electron mobility and decrease threshold voltage by the quality of particles of active thin films annealed at high temperature. But the on/off current ratio reduced by increase of the off current depend on the hot carrier applied to high gate voltage. Even though the size of the particles annealed at low temperature are bigger than HT poly-Si TFTs due to defect in the activated grade poly crystal silicon and the grain boundary, the characteristics of LT poly-Si TFTs were investigated deterioration phenomena those are decrease the electric off current, electron mobility and increase threshold voltage. The results of transconductance show that slope depend on the quality of particles and the amplitude depend on the size of the active silicon particles.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.3
• /
• pp.113-119
• /
• 2013

Grain growth behaviors of hot-rolled AZ31 (Mg-3%Al-1%Zn) and AZ31-0.3%CaO alloys at elevated temperatures have been investigated in order to clarify the effect of CaO addition on grain stability of Mg-Al-based wrought alloy. The grain size of CaO-free alloy increased steeply from 673 K with an increase in annealing temperature from 573 to 773 K, whereas the grains of CaO-containing alloy were relatively stable up to 723 K. The activation energies for grain growth ($E_g$) were 12.2 and 18.3 kJ/mole between 573 and 673 K and 119.2 and 126.9 kJ/mole between 673 and 773 K in the AZ31 and AZ31-0.3%CaO alloys, respectively. This result indicates that grains in the CaO-added alloy possess higher thermal stability than CaO-free alloy. SEM observations on the annealed alloy samples revealed that higher grain stability resulting from CaO addition would be associated with the suppression of grain growth by Ca-related precipitate particles distributed in the microstructure.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.492-495
• /
• 1987

In this study, PLZT ceramics were fabricated by freeze-drying and normal sintering method. The compositional rate of specimen was selected 9/65/35 (La/Zr/Ti) which have good optical and dielectric properties, sintering time was varied 1, 10, 30, 40, 50, 55, 60 and 65 hr at $1250^{\circ}C$. After sintering, the optical and dielectric properties were investigated with the grain size. As the result of the experiment, freeze-dried powder appeared particle size less than 1 um. The relative dielectric constant was increased linearly with the sintering time, specimen which sintered for 65 hr had the highest value, 5780. Grain was grown with increasing time, in the case of specimen sintered for 60 hr, the grain size was 8.4 um. Transmittance was increased with the grain size. In the case of 8.4 um grain size, the transmittance was 56 %. Curie temperature was decreased linearly by the surface-layer effect of space-charge, in the case of grain size which were 1.8 um and 8.4 um, appeared at $100^{\circ}C$ and $80^{\circ}C$, respectively.

• Electrical & Electronic Materials
• /
• v.1 no.1
• /
• pp.35-43
• /
• 1988

In this study, PLZT ceramics were fabricated by the freeze-drying and normal sintering method. The composition rate of the specimen was selected 9/65/35(La/Zr/Ti) which had good optical and dielectric properties, sintering time was varied 1, 10, 30, 50, 55, 60 and 65(hr) at 1250(.deg.C). After sintering, the optical and dielectric properties were investigated with the grain size. As the result of the experiment, the particle size of the powder prepared by freeze-drying method was less than 1(um). The relative dielectric constant was increased linearly with the sintering time and specimen sintered for 65(hr) had the highest value, 5780. Grain was grown with increasing time, in the case of specimen sintered for 60(hr), the grain size was 8.4(um). Transmittance was increased with the grain size. In the case of 8.4(um) grain size, the transmittance was 56(%). Curie temperature was decreased linearly by the surface-layer effect of space-charge. In the case of grain size, 1.8(um), 8.4(um), curie temperatures were appeared at 100(.deg.C) and 80(.deg.C), respectively.

• Journal of Technologic Dentistry
• /
• v.29 no.1
• /
• pp.49-57
• /
• 2007

This study was to add crushed frit with different grain sizes to 3Y-TZP so that it could determine the mechanical properties depending on sintering temperature. In this study, 3 types specimens were prepared in powder with respective additions of 20wt.% frit, which was sized through 24-, 48- and 72-hour ball milling with zirconia. Then, sintered pellets were tested in experiments under the temperature variations for different compositions. As a result, this study came to the following findings: 1. It was found that the higher sintering temperature and the longer ball milling time of frit led to the higher sintered density. 2. Bending strength tended to increase with higher sintering temperature and longer ball milling time of frit. 3. Hardness tended to increase with higher sintering temperature and longer ball milling time of frit. 4. However, it was found that fracture toughness didn't vary significantly depending on sintering temperature. From these findings, it was concluded that the smaller frit grain size and the narrower particle size distribution of frit lead to the better mechanical properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.8-12
• /
• 1994

Solid solutions $Sr_2$($Ta_{1-x}$$Nb_{x}$)$_2$$O_{7}$ (x = 0.0 - 1.0) composed of strontium-tantalate (low Curie temperature) and strontium-niobate (high Curie temperature) were prepared by the conventional mixed oxide method and the molten salt synthesis method (flux method). Phase relation, sintering temperature, grain-orientation and dielectric properties were investigated for sintered ceramic samples with different compositions. Both Curie temperature and dielectric constant at Curie temperature were increased, and sintering behavior and the degree of grain-orientation were improved with the increase of Nb content. Single phase $Sr_2$$Nb_2$$O_{7}$ powder was synthesized by using flux method at lower temperatures, and sintering temperature was also reduced by using flux method derived powder than using mixed-oxide derived powder. Sintering characteristics and dielectric properties of specimens prepared by flux method were better than those derived through the conventional method.

• Journal of Powder Materials
• /
• v.13 no.2 s.55
• /
• pp.129-137
• /
• 2006

In this study, high purity fine $BaTiO_3$ powders were prepared by SHS (Self-propagating High-temperature Synthesis). We would examinate the study of sintering properties and characteristics as a function of temperature with various additives (binder, sintering agent). In separately binder addition, the green and sintered density of specimen were increased as binder content increases. The increased porosity resulted in fine grain size due to the inhibition of grain boundary moving. The $Al_{2}O_{3},\;TiO_{2}$ and MgO playa role of increasing dielectric constants at room temperature. These values were decreased at curie temperature. In case of $SiO_2$, the Curie temperature was decreased. In this study, a high dielectric ceramic capacitor material with temperature stability was synthesized by using various additives.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.36-37
• /
• 2006

Titanium oxy-nitride ($TiN_O_y$) thin films were deposited on $SiO_2$/Si substrates using reactive dc magnetron sputtering, and were then annealed at various temperatures in air ambient to incorporate oxygen into the films. The effect of annealing temperature on the structural and electrical properties of the films was investigated. The grain size of the films decreases with increasing annealing temperature. On the other hand, crystallinity of the films is independent of annealing temperature in air ambient. Resistivity of the films increases remarkably as an annealing temperature increases and temperature coefficience of resistance (TCR) of the films varies from a positive value to a negative value. The films annealed at $350^{\circ}C$ for 30 min exhibited a near-zero TCR value of approximately -5 ppm/K. The decrease of the grain size with increasing annealing temperature was attributed to an increase of oxygen concentration incorporated into the films during anncaling treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.1
• /
• pp.65-74
• /
• 1995

This research was performed to investigate the effect of ageing on grain refinement of 82wt%Cu-13.5wt%Al-4.5wt%Ni-0.1wt% misch metal alloy with ageing temperature and time. The results obtained in this study are as follows; The variation of transformation temperature with ageing temperature had very influence on ageing time at $300^{\circ}C$. But it had not influence on ageing time at $100^{\circ}C$. The variation of transformation temperature after second reversed transformation cycle was not occured in martensitic phase ageing, but $M_s$ point was appeared equally with third reversed transformation cycle in parent phase ageing. The variation of $M_s$ point was not nearly with ageing time at $100^{\circ}C$ ageing temperature. But it was decreasing with ageing time at $300^{\circ}C$ ageing temperature and $A_s$ point was increasing with ageing time. Structure of parent phase ageing was being M18R martensitic and N2H martensitic phase. It was found that ${\alpha}$ and ${\gamma}_2$ phase were created by ageing of long time at $300^{\circ}C$ ageing temperature.