• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.200-210
• /
• 2009

It is necessary to minimize the mismatch of sintering shrinkage between dielectric ceramic and Ni inner electrode layers for the purpose of developing the ultra high-capacity multi layered ceramic condenser(MLCC). Thus, low temperature sintering of dielectric $BaTiO_3$ ceramic should be precedently investigated. In this work, the influence of the milling condition on sintering behavior and electrical properties of $BaTiO_3$ ceramics was investigated in the $BaTiO_3$(BT)-Mg-Dy-Mn-Ba system with borosilicate glass as a sintering agent. As milling time increased, specific surface area(SSA) of the powder increased linearly, while both sinterability and dielectric property were found to be drastically decreased with an increasing SSA. It was also revealed that the sinterability of the excessively milled $BaTiO_3$ ceramics could be recovered by increasing Ba content, rather than increasing glass addition. These results suggest that the sintering behavior of $BaTiO_3$ ceramics under the high SSA was more strongly dependent on the transient liquid phase caused by Ba addition, than the liquid phase from additional glass.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.3
• /
• pp.102-107
• /
• 2007

Dielectric layer of phosphate glass for plasma display panel (PDP) device made by silk screen printing on soda-lime glass. For regulate thermal expansion coefficient (CTE) of between substrate glass and dielectric layer use addition of $Al_2O_3$ and $TiO_2$. The crystallization process of glass-ceramics for dielectric layer have been examined by DTA, XRD some of optical, electrical properties of the dielectric layer were evaluated by UV-spectrometer, dilatometer, impedance analyser. The principal crystalline phase was identified as zinc metaphosphate [$Zn(PO_3)_2$] and zinc pyrophosphate [$Zn_2P_2O_7$]. Reflectance and dielectric constance increased with the addition of $TiO_2$ filler, dielectric constant lower the out side reflectance unchanging of the adding of $Al_2O_3$ filler. Besides CTE was at about $62{\times}10^{-7}/^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.363-364
• /
• 2005

LTCC(low temperature co-fired ceramics)용 glass/ceramic 복합체를 제조하기 위해 3종류 의 glass를 선정하고 filler로 $Al_2O_3$ 와 $TiO_2$를 사용하여 glass frit에 따른 소결 및 유전 특성에 대하여 조사하였다. Glass frit은 lead-borosilicate(PBS), zinc-borosilicate(ZBS), bismuth-borosilicate(BBS) glass 조성을 사용하였고 1100~$1400^{\circ}C$에서 melting시킨 후 quenching하여 frit화하였다. $Al_2O_3$와 $TiO_2$ filler에 10~50 vol%로 glass frit을 각각 혼합한 후 600~$950^{\circ}C$에서 2시간 동안 소결한 결과 50 vol% glass frit 일 때 $900^{\circ}C$ 이하에서 소성이 가능하였다. 유전특성은 $900^{\circ}C$에서 $Al_2O_3$-50vol%PBS($\varepsilon_{r}$=8.8, $Q{\times}f_o$=4,900, $\tau_f$=-24), $Al_2O_3$-50vol% ZBS($\varepsilon_{r}$=5.7, $Q{\times}f_o$=17,800, $\tau_f$=-21), $Al_2O_3$-50vol%BBS($\varepsilon_{r}$=11.1, $Q{\times}f_o$= 2,080, $\tau_f$=-48), $TiO_2$-50vol%PBS($\varepsilon_{r}$=18.6, $Q{\times}f_o$=3,800, $\tau_f$=+135), $TiO_2$-50vol%ZBS($\varepsilon_{r}$=36.4, $Q{\times}f_o$= 7,500, $\tau_f$=+159), $TiO_2$-50vol%BBS($\varepsilon_{r}$=56.4, $Q{\times}f_o$=520, $\tau_f$=+119)을 나타내었다. 따라서 LTCC용 기판재료 및 마이크로파 유전체로 응용이 가능한 것으로 확인되었다.

• Journal of the Korean Ceramic Society
• /
• v.48 no.4
• /
• pp.269-277
• /
• 2011

Glass-ceramics based on lithium disilicate($Li_2Si_2O_5$) are prepared by heat-treatment of glasses in a system of $SiO_2-Li_2O-K_2O-Al_2O_3$ with different compositions. The crystallization heat-treatment was conducted at the temperature range of $700{\sim}900^{\circ}C$ and samples were analyzed by XRD and SEM. Mechanical properties were determined by a Vicker's hardness and 4 point bending strength. When $SiO_2/Li_2O$ ratio increased, cristobalite and tridymite crystals showed more predominate than lithium disilicate crystals. Increase in $Al_2O_3$ contents in the glass suppressed crystallzation of lithium disilicate crystals. Increase in ZnO, $B_2O_3$ contents in the glass decreased crystallization temperature of lithium disilicate crystals, and increased mechanical properties because of the reduction of the lithium disilicate crystal size.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.103-106
• /
• 2009

Fracture characteristics of plate shape using shock tube for glass filled ceramics was carried out. Glass filled ceramics have been considered as a promising candidate material for the dome port cover of air breathing engine. This part of the air breathing engine has an important role separating solid and liquid fuel, and needs the frangible characteristics that the fracture of a part should not affect the internal components of combustion. The objectives of this study are to evaluate the fracture pressures for various thicknesses and diameters of shock impact area. Also fracture phenomena of separated membrane using a shock tube are observed. The experimental apparatus of shock tube consists of a driver, a driven section and a dump tank. The used material is glass filled ceramic made from Corning company. Specimens are used 3, 4.5 and 6mm thickness. Also diameters of shock wave area are chosen 70, 60 and 50 mm. It is expected that the results obtained from this study can be used in the basic data for the dome port cover design of an air breathing engine.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.19-22
• /
• 2015

The joining behavior of YSZ ceramics to the glasses used in the $9Al_2O_3-24ZrO_2-51SiO_2-16R_2O$ and $9Al_2O_3-24ZrO_2-51SiO_2-7La_2O_3-9R_2O$ (wt%) glass systems was investigated. The glass transition and softening temperatures were determined to be $430^{\circ}C$ and $760^{\circ}C$, respectively. The behavior of the contact angle was inversely proportional to an increase in the temperature. The Zr element in YSZ acted as a nucleation agent and contributed to the bonding behavior at the interface.

• Journal of the Korean Ceramic Society
• /
• v.23 no.3
• /
• pp.67-77
• /
• 1986

various properties and manufacturing conditions were investigated in order to synthesize the glass-ceramics of $CaO-P_2O_5$ system for bioceramics. Compositions of easy unidirectional crystallization were between 47.5 and 50, 0mol% CaO For the glass rods prepared by pulling them to about 3 times the original rod length unidirectional crystallization was easier than original glass rods. These samples were crystallized in the axial direction at 15${\mu}{\textrm}{m}$/min in an electric furnace with a temperature gradient of about 3$0^{\circ}C$/cm at 57$0^{\circ}C$. Bending strengths of surface and unidirectionally crystallized samples were investigated with various CaO/$P_2O_5$ molar ratios. The bending strengths of unidirectionally crystallized samples were larger than those of surface -crystallized samples and the value of 47.5CaO.52.5 $P_2O_5$ was 1650kg/$cm^2$. XRD patterns showed that major phase is $\beta$-Ca(PO3) with minor phase 2CaO.$P_2O_5$ Relative crystal-linity of surface-crystallized sample was inversely propertional to the bending strenth. SEM of fracture surface of unidirectionally crystallized samples revealed an unidirectionally aligned structures.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.119-125
• /
• 1996

Magnetic properties through controlled nucleation and crystallization wer studied for ferrimagnetic 40Fe2O3-20CaO-40SiO2 glass useful as thermoseeds for hyperthermia of tumor therapy. The maximum nucleation and crystal growth temperature are $700^{\circ}C$ and 100$0^{\circ}C$ respectively. The glass showed the maximum saturation magnetization of 168.4 emu/cm3 when nucleated $700^{\circ}C$ for 60 min and crystal grown at 100$0^{\circ}C$ for 4hrs. The maximum coercive force was 390 Oe when uncleated $700^{\circ}C$ for 60 min and crystal grown at 975$^{\circ}C$ for 2 hrs. The variation of the saturation magnetization could be well quantitatively interpreted in terms of the volume fraction of the magnetite whereas that of the coercive forces could be explained only qual.itatively in terms of the particle size of the magnetite. Hysteresis losses showed the maximum value of 0.18W/cm3 when heat treated at 100$0^{\circ}C$ for 4 hrs pre-necleated at $700^{\circ}C$ for 60 min and temperature increase of 7K under AC magnetic field of 10 kOe and 10kHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.313-314
• /
• 2006

$BiNbO_4$ ceramics were sintered under the presence of zinc-borosilicate(ZBS) glass and resultant microwave dielectric properties were investigated with a view to applying the composition to LTCC technology. The addition of 5~20 wt% ZBS glass ensured successful sintering below $900^{\circ}C$. In general, increased addition of ZBS glass increased sinterability and temperature coefficient of resonant frequency(${\tau}_f$), but it decreased the dielectric constant(${\varepsilon}_r$) and quality factor($Q{\times}f_0$) significantly due to the formation of an excessive liquid. The sintered $BiNbO_4$ ceramics at $900^{\circ}C$ with 15 wt% ZBS glass demonstrated 25 in dielectric constant(${\varepsilon}_r$), 3,700 in quality factor($Q{\times}f_0$), and -32 $ppm/{\circ}C$ in temperature coefficient of resonant frequency(${\tau}_f$).

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.302-307
• /
• 2000

The objective of this study was to investigate the sintering behavior, crystallization characteristic of glass-ceramic and optimal sintering condition on the glass/ceramic composite for fabricating substrate of LTCC. Glass/ceramic composite was made from alumina powder and glass frit, which was composed of SiO2-TiO2-RO-PbO/(R: Ba, Sr, Ca), and was sintered for 0, 30, 60minutes in the temperature range from 700$^{\circ}C$ to 1000$^{\circ}C$. Properties of frit and glass/ceramic compsoite were analyzed by DTA, XRD, SEM and Network Analyzer and so on. Main sintering mechanism was densification occurred above 730$^{\circ}C$ by viscous flow and crystallization starting about 780$^{\circ}C$ affected sintering also. So viscous flow was affected by sintering temperature, duration time, and creation of crystallization phase etc. From this study, it was possible to fabricate glass/ceramic composite by changing sintering temperature and duration time.