• Journal of Welding and Joining
• /
• v.19 no.3
• /
• pp.305-310
• /
• 2001

UBM-coated Si-wafer was fluxlessly soldered with glass substrate in $N_2$ atmosphere using plasma cleaning method. The bulk Sn-37wt.%Pb solder was rolled to the sheet of $100\mu\textrm{m}$ thickness in order to bond a solder disk by fluxless 1st reflow process. The oxide layer on the solder surface was analysed by AES(Auger Electron Spectroscopy). Through rolling, the oxide layer on the solder surface became thin, and it was possible to bond a solder disk on the Si-wafer with fluxless process in $N_2$ gas. The Si-wafer with a solder disk was plasma-cleaned in order to remove oxide layer formed during 1st reflow and soldered to glass by 2nd reflow process without flux in $N_2$ atmosphere. The thickness of oxide layer decreased with increasing plasma power and cleaning time. The optimum plasma cleaning condition for soldering was 500W 12min. The joint was sound and the thicknesses of intermetallic compounds were less than $1\mu\textrm{m}$.

• Applied Microscopy
• /
• v.25 no.1
• /
• pp.130-138
• /
• 1995

TEM specimen preparation methods have been examined to characterize Cu oxide particles in the polyimide film. Polyimide films were prepared by coating polyamic acid onto Cu films which had been deposited on TEM-mask and glass substrates and Cu foil, followed by thermal curing. In case of TEM-mask, direct observation was possible without further preparation. In other cases, TEM specimen were made by separating polyimide film from the substrate. Polyimide films were removed from glass and Cu foil by dissolving glass in HF solution and Cu foil in $H_{2}SO_{4}$ solution. TEM-mask observation confirms that fine $Cu_{2}O$ particles precipitate in the polyimide as a result of reaction of polyamic acid with Cu. However $Cu_{2}O$ particle reacts with HF and $H_{2}SO_{4}$ solution during dissolving the substrate and interpretation could be misled. It is concluded characterization of $Cu_{2}O$ particle in polyimide using TEM-mask is better than other methods.

• Journal of the Korean Society for Heat Treatment
• /
• v.12 no.3
• /
• pp.199-205
• /
• 1999

The quaternary Ti-Al-V-N films have been grown on glass substrates by reactive dc and rf magnetron sputter deposition from a Ti-6Al-4V target in mixed Ar-$N_2$ discharges. The Ti-Al-V-N films were investigated by means of X-ray diffraction(XRD), electron probe microanalysis(EPMA) and scratch tester. Both XRD and EPMA results indicated that the Ti-Al-V-N films were of single B1 NaCl phase having columnar structure with the (111) preferred orientation. Scratch tester results showed that the adhesion strength of Ti-Al-V-N films which treated with substrate heating and vacuum annealing was superior to that of as-deposited film. The good adhesion strength was also achieved in the double-layer structure of Ti-Al-V-N/Ti-Al-V/Glass.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.213-219
• /
• 2011

Recently aspheric lenses are widely used for superpricision optical instruments, such as cellular phone camera modules, digital cameras and optical communication modules. The aspherical lenses are processed using mold core under high temperature compressive forming pressure. It is imperative to develop superhard protective films for the life extension of lens forming mold core. Especially ta-C films with higher $sp^3$ fractions receive attentions for the life extension of lens forming mold and, in turn, the cost reduction of lenses due to their suprior high temperature stability, high hardness and smooth surfaces. In this study ta-C films were processed on WC mold as a function of substrate bias voltage using FVA (Filtered Vacuum Arc) method. The processed films were characterized by Raman spectroscopy and nano-indentation to investigate bonding nature and hardness, respectively. The film with maximun 87% of $sp^3$ fraction was obtained at the substrate bias voltage of -60 V, which was closest to ta-C film. ta-C films showed better high temperature stability by sustaining relatively high fraction of $sp^3$ bonding even after 2,000 glass lens forming applications.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.149-154
• /
• 2000

Bi-layer Mo films were deposited on soda-lime glass substrates using DC magnetron supttering. Increasing gas pressure, the resistivity varied from $1\times10^{-5}\; to\; 8.3\times10^{-3}\; \Omega.cm$. Furthermore, stress direction yielded compressive-to-tensile transition stress curves. The micro-structure of the compressively-stressed film which had poor adhesion consists of tightly packed columns, but of the tensile-stressed films had less dense structure. Under all gas pressure conditions, Mo films exhibited distinctly increasing optical reflection with decreasing gas pressure. The expansion of (110) peak width with the gas pressure meant the worse crystalline growth. The impurity levels in the Mo film exhibited highly concentrated Na, Se and O elements due to less dense micro-structure. The degree of Na diffusion depends on the type of the glass substrate used and the nature of the Mo film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.12
• /
• pp.867-871
• /
• 2013

The Ti adhesion layers were deposited onto the glass substrate for transparent capacitors using $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMNO) dielectric thin films. Graphene was transferred onto the Ti/glass substrate after growing onto the Ni/$SiO_2$/Si using rapid-thermal pulse CVD (RTPCVD). The BMNO dielectric thin films were investigated for the microstructure, dielectric and leakage properties in the case of capacitors with and without Ti adhesion layers. Leakage current and dielectric properties were strongly dependent on the Ti adhesion layers grown for graphene bottom electrode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.178.1-178.1
• /
• 2015

In and Ga doped ZnO (IGZO) thin films were prepared by radio frequency magnetron sputtering without intentional substrate heating on glass substrate and TiO2-deposited glass substrates to consider the effect of a thin TiO2 buffer layer on the optical and electrical properties of the films. The thicknesses of the TiO2 buffer layer and IGZO films were kept constant at 5 and 100 nm, respectively. Since the IGZO/TiO2 bi-layered films show the higher FOM value than that of the IGZO single layer films, it is supposed that the IGZO/TiO2 bi-layered films will likely perform better in TCO applications than IGZO single layer films.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1125-1131
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on the two kinds of polyimide (PI) surfaces using thin plastic substrates. The NLC pretilt angles generated on thin plastic substrates are higher than that on the glass substrate. We study that AFM (atomic force microscope) image of rubbed PI surface with polymer film has formed the micro-groove. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.480-485
• /
• 1993

Factros considered building the magnetron sputtering system for TFT LCD (thin film transistor liquid crystal display0 metallization were thin film thichnes uniformity, temperature uniformity and the pressure gradient of sputtering gas flow in vacuum chamber, base pressure, and the stability fo the carrier moving . The system was consisted of a deposition chamber, a pre-heating chamber, a RF-precleaning chamber and a load/unload lock chamber. The system was designed to handle a substrate with dimension of 400$\times$400mm. The temperautre uniformity of a heater table developed showed $250 ^{\circ}C\pm$5% accuracyon the substrate glass. A base pressure of 1.8 $\times$10-7 torr was obtained after 24 hours pumping with a cryo pump. After an aluminum target was installed in a sputtering source and the film wa sdeposited on the glass, the uniformity, reflectivity and sheet resistance of the deposited film were measured.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.138-143
• /
• 2010

This paper presents the analysis, the fabrication and the test results of a micro passive gas pressure regulator to keep the outlet pressure costant even for a widely-varying inlet pressure. This device is to regulate the outlet pressure according to the applied reference pressure based on the pressure balancing mechanism of the structure including a membrane and a valve. This regulator consists of four layers; a bulk-micromachined silicon substrate, a sandblasted glass substrate, a PDMS valve seat layer and a glass valve layer. The device size is $10\times13\times1.7 mm3$. The device was fabricated by micromachining. The characteristic of the device was analyzed and tested. The characteristic of the fabricated pressure regulator is similar to that obtained from the analysis. The pressure regulator of this paper is feasible for portable systems and miniature drug delivery systems.