• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.11
• /
• pp.792-798
• /
• 2012

A general concept on the definition of the second law efficiencies of thermodynamic cycles is introduced. The efficiency is defined to be proportional to the entropy generation divided by the maximum possible entropy generation. This way of definition of the cycle efficiency is clear and concise and, moreover, follows faithfully the concept of the second law of thermodynamics. This definition is applied to heat engine, refrigerator and heat pump. The second law efficiencies of heat engine and refrigeration cycles are derived, which are the same as the existing ones, respectively. The second law efficiency of heat pump, however, finds to be different from the existing one. Discussion is given about the difference and its cause.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.176-182
• /
• 2013

In this study, we examine the tracking happen in a polyvinyl-chloride-sheathed flat cord (PVCSFC), which is widely used as a distribution cord. The study classifies the bridge current via the formed conductive paths during tracking in the PVCSFC. Further, it attempts to distinguish the characteristics of heat generation and heat transfer by kind of bridge current. When the PVCSFC is in the static state, the bridge currents flow only through the electrolyte bridge. In the case of the carbonized PVCSFC, the bridge currents flow through one or more conductive paths. One is the electrolyte bridge, the other is the bridge that is consisted electrolyte and carbonized insulation. Currents flowing through different conductive paths have different heat generation and transfer characteristics. As the bridge current flowing in the conductive path consisting of electrolyte and carbonized insulation increases, the temperature difference between the surface of the PVCSFC and ambient air also increases correspondingly.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.68-74
• /
• 2008

This paper describes the causes and effects that have influence on thermoelectric generation. If heat transfer is unequal to thermoelectric modules, we could not get the maximum thermoelectric power. So, by experiment, we analysed the differences of power generation according to the state of the contact between thermoelectric module and heat source. And with the variation of heat transfer area, the generated power was analysed also. Using the experimental results we proposed a thermoelectric generation system.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.89-94
• /
• 2006

For a development of the software which estimates the economics of a combined heat and power generation system in apartment estates, the thermal consumption and electric power consumption data were investigated in about 115 apartment estates. And the algorithm was developed, then the software was made by the macro function of the Excel spread sheets.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.9 no.4
• /
• pp.1-9
• /
• 2001

The temperature and moisture distributions in a dry room with a heat and moisture source -i.e., workers- are studied numerically by using a standard $k-\varepsilon$ turbulence model. In order to evaluate the effectiveness of heat and moisture ventilation inside the room, the heat removal capacity and the moisture exhaust efficiency are introduced. The effectiveness of ventilation control is analyzed by evaluating the temperature and humidity distributions in the room quantitatively. It is found that the mean absolute humidity inside the room is almost constant regardless of the models and the heat generation rates in this study range. This results from the fact that the moisture generation by the workers was relatively small. Through the modification of the design, 40% improvement in critical decay time was achieved.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.85-91
• /
• 2011

Experimental analysis has been carried out to investigate thermal characteristics of hydraulic system in special vehicles. Hydraulic system performance is largely influenced by oil temperature, and there are considerable performance decline and malfunctions in the system for high temperature conditions caused by heavy load and continuous operation. Transient oil temperature and pressure variation are analyzed and heat generation rates in the several main system parts are compared for various flow rates. With the start of system operation oil temperature gradually increases, and viscosity deceases by about 70% as temperature increases from $20^{\circ}C$ to $80^{\circ}C$. Operation pressure in the hydraulic system decreases with oil temperature, and its variation rate becomes less steep as oil temperature increases. Heat generation rate in hydraulic pump also depends on the oil temperature, and it reaches maximum near $50^{\circ}C$. These results in this study can be applied to optimal design of efficient hydraulic system in special vehicles.

• Bulletin of the Korean Mathematical Society
• /
• v.20 no.2
• /
• pp.99-103
• /
• 1983

Internal heat generation is one of the insidious conditions affecting the quality of an industrial product after it is cast, coated, molded, forged or laminated. Frequently, the product is pressed into service before the exothermic chemical reactions in the generic material has been completed. The heat liberated from this continuing chemical reaction or the residual deformation from the rheological activities in the materials must be adequately removed or prevented, or the product may be discolored, warped, weakened or even "ignited" spontaneously. Numerous instances of premature structural failures, product-recalls, and/or system-malfunctions have been recorded in recent history. The Coulee Dam was poured with pre-chilled concrete just to negate this freakish encore. It is well-known that concrete (a non-isotropic conducting medium), for instance, takes 28 days to develop its full strength. During this period of curing it is conceivable that the processes of internal heat generation, heat conduction and heat dissipation take place simultaneously inside the medium.he medium.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.1
• /
• pp.122-130
• /
• 1998

The present work analyzes the pressure drop and heat transfer characteristics of the plate heat exchanger with staggered dimples. The flow is assumed to be constant property, three dimensional and laminar. A thermal boundary condition is uniform wall temperature and it is assumed that the flow is periodically fully developed. Elliptic grid generation is used for proper modelling of the internal tube geometry with dimples. Computations have been carried out for a variety of geometric parameters, Reynolds number, and Prandtl number. The friction factor ratio and the ratio of a module average Nusselt number are presented for the cases considered in this study. It is found that the distance between dimples has a substantial effect on the pressure drop and heat transfer.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.8
• /
• pp.13-22
• /
• 2018

The purpose of this study was to consider the energy generation of the building as well as the energy demand of the building in terms of zero energy building design. The reason why the zero energy building viewpoint should be discussed is that direction of the building, heat transfer rate of the building, and the S/V ratio of the building are variables related to energy demand and solar panels installed on the building roof and building envelope are variables related to energy generation. This study proceeded as follows; Firstly, the simulation model of large office and elementary school has the same mutual volume and total floor area, and the each floor area and number of floors are adjusted so that the S/V ratio is different. To the next, the energy demand and energy generation of the simulation model were derived based on the meteorological data of Seoul, Daejeon, Busan. Finally, energy demand, energy generation, and final energy demand were compared with heat transfer rate, S/V ratio, building type, region, and orientation. The results of this study is that consideration of solar power generation in terms of energy generation should be taken into consideration at the same time in consideration of the heat transfer rate, the shape, the region and the direction of the zero energy building design.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.175-180
• /
• 2008

Thermoelectric materials convert temperature difference to electric power for power generation and vice versa for refrigeration. Recent advances in enhancing the thermoelectric figure-of-merit shed light on efficient power generation from the waste heat available in industries and vehicles. Nanoscale phenomena with both nanoscale constituent-embedded bulk samples and nanoscale materials proving enhanced thermoelectric performance have been widely reviewed. Bulk materials of crystal-orientation and nano-structured particle embedding seem to promise a higher thermoelectric figure-of-merit and an effective power generation application. As a preliminary study, Si-Ge nanocomposite was prepared with spark plasma sintering method and its properties were examined.