• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.9-19
• /
• 1997

In this paper, the modeling and analysis of dynamic characteristics has been carried out for friction clutches and brakes in an automatic transmission. From the operating oil pressure generated by the valve-body, time delay by check valve and the movement of piston has been examined. Also torque capacity and torque transferred at the clutch is studied. Heat capacity and temperature distribution at the reaction plate of clutch are codeled by time-dependent, nonhomogeneous partial differential equation, and brake torque, brake time, and the amount of heat generated are investigated. It is found that the time delay at the check valve is very short but dominant at the spool.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.561-565
• /
• 2008

Generally, reaction wheels or thrusters are used for attitude control of a satellite. There is a potential method for the attitude control utilizing the plasma flow on the Low Earth Orbit. In the present study, experiments which simulate attitude control of a Low Earth Orbit Satellite using the ionosphere were conducted. In this experiment, a plasma flow was generated by a steady-state Hall type accelerator. However it is known that the Hall type accelerator, which is used as plasma source, produces a torque around its axis called "swirl torque". This torque would affect the attitude control in the above-mentioned experiments. First of all, we conducted the measurement of the swirl torque. Secondly, experiments using a satellite model with negative electrodes were conducted. The negative electrodes generated torque around the axis, and controlled the attitude of the satellite model by changing the applied voltage.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.517-522
• /
• 1991

In this paper, robot's grasping poses are classified into three cases, and force/torque information in each grasping pose is analyzed. In the grasping process, error between the desired and the actual grasping poses can be generated because of uncertainty in the environment. A systematic algorithm is presented, that uses the force/torque information generated by grasping pose error to estimate robot's actual grasping pose.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.675-679
• /
• 2007

The control method of programmable dynamometer for overall test of machine is to load reference torque which is computed from torque transducer into motor under test. But the torque information detected from torque transducer have a lot of noise when the load torque of moter is a small quantity or changing. Thus, torque transducer must have a low pass filter to detect a definite torque information. But The torque delay generated by filter with torque transducer occur a torque trouble for moter torque of programmable dynamometer. Therefore, this kind of system could not perform dynamic and nonlinear load. In this paper, the control method using the load torque observer without a measure for torque transducer is proposed. The proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction moter. Therefore, the torque controller is not affected by a load torque disturbance.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.427-432
• /
• 2003

The control method of programmable dynamometer for overall test of machine is to load the reference torque which is computed from torque transducer into motor under test. But the torque information detected from torque transducer have a lot of noise when the load torque of moter is a small quantity or changing. Thus, torque transducer must have a low pass filter to detect a definite torque information. But The torque delay generated by filter with torque transducer occur a torque trouble for meter torque of programmable dynamometer. The proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction meter. Therefore, the torque controller is not affected by a load torque disturbance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1108-1110
• /
• 2003

The control method of programmable dynamometer for overall test of machine is to load the reference torque which is computed from torque transducer into motor under test. But the torque information detected from torque transducer have a lot of noise when the load torque of meter is a small quantity or changing. Thus, torque transducer must have a low pass filter to detect a definite torque information. But The torque delay generated by filter with torque transducer occur a torque trouble for meter torque of programmable dynamometer. The proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction moter. Therefore, the torque controller is not affected by a load torque disturbance.

• 한국유체기계학회 논문집
• /
• 제16권6호
• /
• pp.5-11
• /
• 2013

Torque control methods of wind turbine are mainly classified into two methods: torque-mode and speed-mode methods. The traditional torque-mode method, in which generator torque proportional to square of generator speed is determined, has been chosen in many wind turbines but its response is slower as they are larger in multi-MW size. Torque control methods based on both speed-mode and torque-mode can be used to make response of wind turbine faster. In this paper, two torque control methods based on the traditional torque-mode method are applied to a 2.75 MW wind turbine. It is shown through some simulation results for real turbulence wind speeds that torque control method based on torque-mode has the merit of reducing fluctuations of generated power than PI controller based on speed-mode.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.610-614
• /
• 2000

Torque pulsation generated in every commutation period is the main drawback of BLDC motor which deteriorates the precision of BLDC motor. Many methods to solve this problem have been proposed. In this paper a new torque model considered with decaying phase back EMF is introduced and from it the cause of torque pulsation in commutation period is analyzed. Form this analysis new algorithms to reduce the torque pulsation by commutation time are proposed and with simulation the validity is verified.

• 전기학회논문지
• /
• 제58권12호
• /
• pp.2391-2395
• /
• 2009

Active control schemes which modify the excitation to correct for any of the nonideal characteristics of the SPMSM is described. Especially, because of design limitations(size and cost) in automobile, the back-EMF of SPMSM can't be perfectly designed with sinusoidal wave and iron core of stator is saturated so that torque ripple is unavoidable. An active cancellation method of the pulsating torque components which would otherwise be generated using the classic sinusoidal current excitation is illustrated.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권5호
• /
• pp.245-249
• /
• 2006

This study tries to test and analyze the static friction torque generated by an electromagnetic clutch. Then the torque is improved by optimizing the shape of armature. For the purpose of design change and optimization of the electromagnetic clutch, the static friction torque prediction is very important. We construct an axi symmetric FEM model for analyzing the static friction torque and used a torque tester for evaluating the real torque. For a test, predicted static friction torque is compared with the experimental one to discuss the rationality of torque analysis process. The analytical result agrees well with experimental data, explaining the validity of the mathematical process and FEM model. After confirming the torque analysis process, the optimization process is investigated. The optimization result shows that the static torque is improved by changing the armature shape.