• 한국강구조학회 논문집
• /
• 제12권3호통권46호
• /
• pp.269-279
• /
• 2000

차량하중의 증가 및 부식 등에 의해 손상된 강교량 구조물들은 보수 보강이 요구되어진다. 손상부채를 보수 보강하는 방법은 단면결손이 없다는 장점을 가진 용접에 의한 보수방법이 유리하다. 3차원 탄소성해석 결과를 토대로 공용중 보수용접에 의해 생기는 응력과 변형의 거동에 대해 연구하였다. 균열이 있는 부재에 하중만 작용할 경우 과도 응력의 크기는 보수용접균열길이 및 균열깊이가 큰 순으로 크다. $80MPa({\sigma}_y/3)$ 및 $140MPa({\sigma}_a)$의 응력 작용시 보수용접에 의해 발생되는 응력의 크기는 무응력 상태에서 보수용접시 발생되는 응력의 크기와 하중재하에 의해 생긴 응력의 크기의 합과 비슷하다. 응력 작용시 보수용접에 의해 발생되는 용접선방향 인장과도응력 성분은 부재폭에 대한 균열 길이비(1/b)가 커지면 커짐을 알 수 있다. 또한, 응력 작용시 보수용접에 의해 발생되는 용접선 직각방향의 면내수축변위의 크기는 보수용접길이가 긴순으로 크다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.913-922
• /
• 2009

Fourteen model pile load tests using a calibration chamber and instrumented model pile were preformed to investigate the variation of the behaviors of driven piles in sands with soil and lateral cyclic loading conditions. Results of the model tests showed that the first loading cycle generated more than 70% of the pile head rotation developed for 50 lateral loading cycles. Lateral cyclic loading also made an increase of the ultimate lateral load capacity of piles for $K_0$=0.4 and an decrease for $K_0$ higher than 0.4. Higher portion of the increase or decrease in the ultimate lateral load capacity by lateral cyclic loading was generated for the first loading cycle due to densification of loosening of the soil around the pile by lateral cyclic loading. It was also observed that a two-way cyclic loading caused higher ultimate lateral load capacity of driven piles than a one-way cyclic loading. When the pile was in the ultimate state, the maximum bending moment developed in the pile increased with increasing $K_0$ value of soil and was insensitive to the magnitude and number of lateral cyclic loading.

• Structural Engineering and Mechanics
• /
• 제17권5호
• /
• pp.655-670
• /
• 2004

This paper aims to evaluate the effect of typhoons on fatigue damage accumulation in steel decks of long-span suspension bridges. The strain-time histories at critical locations of deck sections of long-span bridges during different typhoons passing the bridge area are investigated by using on-line strain data acquired from the structural health monitoring system installed on the bridge. The fatigue damage models based on Miner's Law and Continuum Damage Mechanics (CDM) are applied to calculate the increment of fatigue damage due to the action of a typhoon. Accumulated fatigue damage during the typhoon is also calculated and compared between Miner's Law and the CDM method. It is found that for the Tsing Ma Bridge case, the stress spectrum generated by a typhoon is significantly different than that generated by normal traffic and its histogram shapes can be described approximately as a Rayleigh distribution. The influence of typhoon loading on accumulative fatigue damage is more significant than that due to normal traffic loading. The increment of fatigue damage generated by hourly stress spectrum for the maximum typhoon loading may be much greater than those for normal traffic loading. It is, therefore, concluded that it is necessary to evaluate typhoon induced fatigue damage for the purpose of accurately evaluating accumulative fatigue damage for long-span bridges located within typhoon prone regions.

• 한국안전학회지
• /
• 제11권4호
• /
• pp.3-9
• /
• 1996

In this study, comparison of theoretical solutions with experimental results is examined through fracture conditions for the case of float glasses subjected static loading. The range of fracture generation limits and critical penetration energies are solved according to the impactor mass under the high velocity, and analytical method of fracture strength and penetration strength are presented. Also, fracture patterns are investigated according to impact velocities. The results obtained from this study are as follows ; 1) Radial cracks are generated from the loading point regardless of plate thickness in the case of the plate subjected to the static loading. In the case of high-speed impact, dimensions of ring cracks become to smaller and length of radial cracks becomes shorter with the rapidity of impact velocity. 2) Kinetic change volume of collision after/before is constant regardless of velocities over the range of critical penetration velocity. 3) Although the same impact energy is working, the critical penetration energy is increased with the shorter of impactor mass. 4) Although the same impact energy is working, the penetration fracture of lighter Impactor mass is generated more than that of heavier impactor mass, and the impulse of lighter impacter mass appear more than that of heavier impactor mass. Therefore, the penetration fracture in the case of greater impulse is generated earlier regardless of the of the dimensions of Impact loading.

• 도시과학
• /
• 제11권2호
• /
• pp.45-54
• /
• 2022

Recently, regulations on automobile exhaust gas emission are being strengthened. Accordingly, automobile exhaust gas emissions are expected to decrease and continue to decrease. On the other hand, many countries do not yet consider the emission of non-exhaust air pollutants from automobiles as important. Automobile non-exhaust substances are classified into three categories: tire dust emissions, brake wear emissions, and road scattering dust. In particular, in the case of tire dust, research results exist that pollutant emissions increase as the weight of a vehicle increases. Since the weight of trucks varies according to the load and the load along the axles is also different, it can be expected that the emission of PM10 from the tire dust will be different depending on the loading method. Therefore, this study was conducted on the amount of PM10 generated in tire dust considering the axle load of the truck according to the loading method. However, it was confirmed that the total amount of PM10 was less than that all loads are loaded in the front or rear when the load was evenly distributed in the front and rear of the cargo compartment. In particular, if the load is distributed evenly in the front and back of the cargo compartment and the load in the front part is divided into 2 to 6 and loaded, as the number of divided loading increases the amount of PM10 generated decreases. And when the load is divided into 6 pieces, the total amount of PM10 generated is 0.3952g, the minimum value. If the load is divided into 6 or more and loaded evenly, the total PM10 generated continuously increases and converges to about 0.3964g.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.913-920
• /
• 1996

In this study, the counting method for multi-axial and multi-point load states was proposed. Using this counting method, the load spectrum is generated from the service load history which is measured for boom structure of excavator. Loading state for loading points of boom structure is described as a multi-dimensional state space. From this load spectrum, the stress spectrum was generated by FEM analysis using the superposition of the unit load. The cumulated damage at the severe damage point of In nm structure by the failure example is calculated by Palmgren-Miner's rule. As a result of this study, the fatigue life estimation using the multi-axial and multi-point load counting method is useful.

• Industrial Engineering and Management Systems
• /
• 제3권1호
• /
• pp.22-37
• /
• 2004

An integrated heuristic approach based on genetic algorithms (GAs) is proposed for solving the container selection and loading problems. The GA for container selection solves a two-dimensional knapsack problem, determining a set of containers to minimize the transportation or shipment cost. The GA for container loading solves for the weighted coefficients in the evaluation functions that are applied in selecting loading positions and boxes to be loaded, so that the volume utilization is maximized. Several loading constraints such as box orientation, stack priority, stack stability, and container stability are also incorporated into the algorithm. In general, our computational results based on randomly generated data and problems from the literature suggest that the proposed heuristic provides a good solution in a reasonable amount of computational time.

• 한국철도학회논문집
• /
• 제14권1호
• /
• pp.49-56
• /
• 2011

이 논문에서는 모형토조 실험으로 하중을 재하하는 방법에 따라 응력과 침하특성을 비교하였으며, 하중재하 방법의 차이를 정량적으로 평가하기 위하여 응력경로와 주응력 방향의 회전영향을 평가하였다. 실험결과 동일 시험조건에서 하중재하 방법에 따라 침하량과 토압이 달라지며, 이동하중의 경우 고정된 지점에서의 정적하중보다 침하량이 약 6배, 반복하중보다 약 2배 이상 크게 발생하였다. 응력경로에서도 고정된 지점에서의 반복하중보다 응력경로의 길이(L)는 2배 이상이 길고 전단변형에 영향을 주는 축차응력도 약 2배 이상 크게 나타났다. 또한, 도상자갈이 있는 궤도에서의 이동하중의 경우 주응력 방향의 회전각이 약 ${\Delta}{\theta}=40^{\circ}$ 최대 응력의 약 60%정도 발생하고 있으며, 주응력 방향의 회전에 영향을 받고 있다는 것을 알 수 있었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.321-324
• /
• 1999

• 환경영향평가
• /
• 제21권4호
• /
• pp.543-552
• /
• 2012

Namgang mid-watershed is located in downstream of Nakdong river basin. There are many pollution sources arround this area and it's control is important to manage a water quality of Nakdong river. A target year of Namgang mid-watershed water environment management plan is 2013. To predict a water quality at downstream of Namgang, we have investigated and forecasted the pollutant source and it's loading. There are some plan to construction the sewage treatment plants to improve the water quality of Nam river. Those are considered on predicting water quality. As results, it is shown that the population is 343,326 and sewerage supply rate is 79.2% and the livestock is 1,662,000 in Namgang mid-watershed. It is estimated that the population is 333,980, the sewerage supply rate is 86.9% in 2013. The milk cow and cattle were estimated upward and the pigs were downward by 2013. The generated loading of BOD and TP is 75,957 kg/day and 4,311 kg/day, discharged loading is 18,481 kg/day and 988 kg/day respectively in 2006. It were predicted upward the discharged loading of BOD and TP by 4.08% and 6.3% respectively. The results of water quality prediction of Namgang4 site were 2.5 mg/L of BOD and 0.120 mg/L of TP in 2013. It is over the target water quality at that site in 2015 about 25.0% and 9.1% respectively. Consequently, there need another counterplan to reduce the pollutants in that mid-watershed.