• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.370-370
• /
• 2006

Thermoplastic elastomer gels, which has molecular networks composed of a microphase-separated multiblock copolymer swollen to a large extent by a low volatility mid-block selective solvent such as white oil have various applications. In this particular study, the effect of several network-forming nanoscale fillers such as two different graphite particles and carbon nanotube on the properties of TPE gels prepared from a microphaseordered poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS) triblock copolymer with an EB compatible white oil was studied. The linear viscoelastic behavior, sol-gel transition, x-ray diffraction and mechanical properties were discussed. The properties of thermoplastic elastomer gels hybrid with graphite prepared by mixing Poly(styrene-b-ethylene-co-butylene)-b-styrene) with paraffin oil and different amount of expandable graphite were found to increase the mechanical properties at only lower graphite concentration but tends to decrease when paraffin oil/SEBS ratio is lower. The gelation temperature is the same for all TPE gels with different amounts of graphite. Both storage (G') modulus loss (G") modulus of TPE gels slightly increase with addition of graphite.

• 한국세라믹학회지
• /
• 제31권7호
• /
• pp.795-803
• /
• 1994

Ferroelectric BaTiO3 thin film was produced using BaTi-ethoxide sol. This sol was prepared from BaTi-ethoxide by a partial hydrolysis with ammonia as a basic catalyst and ethylene glycol as a chelating agent. BaTiO3 thin film was prepared from three continuous spin-coating layers of the sol on bare Si(100) wafer at 2500 rpm followed by pyrolysis at $700^{\circ}C$ for 30 min. After the heat treatment, the film was 0.200$\pm$0.010 ${\mu}{\textrm}{m}$ thick and its grain size was 0.059 ${\mu}{\textrm}{m}$. On the other hand, electrical properties were measured for BaTiO3 thin film separately prepared on Au-deposited silicon wafer. The dielectric constant and loss of the BaTiO3 thin film at room temperature was 150~160 and 0.04 respectively, which was measured at 10 kHz and oscillation level of 0.1 V. In the measurements of the dielectric properties at high temperatures, it was observed that the capacitance of the thin film increases steeply, while the dielectric loss reaches maximum around 1$25^{\circ}C$, which corresponds a phase transition from tetragonal to cubic BaTiO3.

• Macromolecular Research
• /
• 제11권5호
• /
• pp.352-356
• /
• 2003

The objectives of this study were to investigate the influence of gamma irradiation for sterilization on poly(D,L-lactide-co-glycolide) (PLGA) with different molecular weight and the effect of gamma irradiation on the release behavior of 1,3-bis(2-chloroethyl)-1-nitrosourea (BCNU, carmustine) from PLGA wafer with various irradiation doses. The effect of gamma irradiation on PLGA was evaluated by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and electron paramagnetic resonance (EPR). The weight average molecular weight (M$_{w}$) and glass transition temperature (T$_{g}$) of PLGA decreased after gamma irradiation. The extent of M$_{w}$ reduction was dependent on irradiation dose and PLGA molecular weight. Using EPR spectroscopy, we successfully detected gamma irradiation induced free radicals in PLGA. The gamma irradiation increased the release rate of BCNU from PLGA wafer at applied irradiation doses except 2.5 Mrad of irradiation dose in this study.study.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.487-488
• /
• 2006

Novel bisphenol-based wholly aromatic poly(ether sulfone-ketone) copolymer containing pendant sulfonate groups were prepared by direct aromatic nucleophilic substitution polycondensation of 4,4-difluorobenzophenone, 2,2'-disodiumsulfonyl-4,4'-fluorophenylsulfone (40mole% of bisphenol A) and bisphenol A. Polymerization proceeded quantitatively to high molecular weight in N-methyl-2-pyrrolidinone at $180^{\circ}C$. Organic-inorganic composite membranes were obtained by mixing organic polymers with hydrophilic $SiO_2$ (ca. 20nm) obtained by sol-gel process. The polymer and a series of composite membranes were studied by FT-IR, $^1HNMR$, differential scanning calorimetry (DSC) and thermal stability. The proton conductivity as a function of temperature decreased as $SiO_2$ content increased, but methanol permeability decreased. The nano composite membranes were found to posse all requisite properties; Ion exchange capacity (1.2meq./g), glass transition temperatures $(164-183\;^{\circ}C)$, and low affinity towards methanol $(4.63-1.08{\times}10^{-7}\;cm^2/S)$.

• Elastomers and Composites
• /
• 제45권4호
• /
• pp.286-290
• /
• 2010

Coumarin기가 포함된 액정성을 가진 단량체를 액정 상태에서 UV 조사에 의해 중합하였다. Cycloaddition 반응에 의해 coumarin 액정 단량체는 이량체로 전환되었으며, 광이량화 반응 후에도 액정성이 유지되었다. 그리고 이러한 이량체는 단량체의 액정범위 보다 넓은 영역에서 액정성을 나타내었다. 화합물의 구조는 FT IR 및 $^1H$ NMR에 의해 확인하였으며, 그들의 열적 상전이온도 및 열안정성들은 DSC, GPC 및 편광현미경에 의해 조사하였다. 광중합에 의해 생성된 고분자 생성물은 광학 편광 현미경 관찰에 의해 스멕틱 및 네마틱 조직을 갖는 쌍방성 액정성을 보였다.

• 한국자기학회지
• /
• 제19권5호
• /
• pp.180-185
• /
• 2009

Sol-gel 법을 이용하여 Fe$_3$O$_4$ 분말을 합성하였으며, 합성한 분말의 구조적 특성, 입자의 모양 및 크기, 자기적 특성에 관하여 연구하였다. 두 가지의 다른 성분비 (Fe$^{2+}$와 Fe$^{3+}$의 몰 당량비를 1 : 2와 Fe$^{2+}$ 만을 사용)와 2-methoxyethanol 용매를 사용하여 refluxing한 후, 질소 분위기에서 200$\sim$600$^{\circ}C$로 열처리하여 페라이트 분말을 합성할 수 있었다. X-선 회절기를 이용하여 합성한 시료의 결정구조를 확인한 결과 두 경우 모두 250$^{\circ}C$ 이상의 열처리로 단일상의 spinel 페라이트가 만들어짐을 확인할 수 있었다. 전계방출 주사전자현미경을 이용하여 관측한 결과에 의하면 열처리 온도가 높아짐에 따라 입자의 크기 증가를 관측할 수 있었다. Mossbauer 분광 실험에서 입자의 크기 변화에 따른 상자성체에서 준강자성체로의 전이를 관측할 수 있었다. 몰 당량비를 1 : 2의 비율로 혼합 후 250$^{\circ}C$에서 열처리한 분말은 크기가 상자성체와 준강자성체의 경계에 위치하며 이중 78%의 시료는 준강자성체의 특성을 22%의 분말은 상자성체의 특성을 가짐을 알 수 있었다. Fe$^{2+}$ 이온만을 사용하는 만든 Fe$_3$O$_4$ 분말은 200$^{\circ}C$의 열처리로 spinel 구조를 가지나 입자의 크기가 작아서 상자성체의 특성을 지닌다. 250$^{\circ}C$ 이상에서 열처리한 시료는 준비 방법에 무관하게 전형적인 Fe$_3$O$_4$ 분말의 연자성 특성을 보이고 있으며, 열처리 온도가 높아감에 따라 포화자화가 증가하고 보자력 또한 증가하는 것을 확인할 수 있었다.

• 전기화학회지
• /
• 제7권3호
• /
• pp.131-137
• /
• 2004

Sol-gel method which provides better electrochemical and physiochemical properties compared to the solid-state method was used to synthesize the material of $LiFe_yMn_{2-y}O_4$. Fe was substituted to increase the structural stability so that the effects of the substitution amount and sintering temperature were analyzed. XRD was used for the structural analysis of produced material, which in turn, showed the same cubic spinel structure as $LiMn_2O_4$ despite the substitution of $Fe^{3+}$. During the synthesis of $LiFe_yMn_{2-y}O_4$, as the sintering temperature and the doping amount of Fe(y=0.05, 0.1, 0.2)were increased, grain growth proceeded which in turn, showed a high crystalline and a large grain size, certain morphology with narrow specific surface area and large pore volume distribution was observed. In order to examine the ability for the practical use of the battery, charge-discharge tests were undertaken. When the substitution amount of $Fe^{3+}\;into\;LiMn_2O_4$ increased, the initial discharge capacity showed a tendency to decrease within the region of $3.0\~4.2V$ but when charge-discharge processes were repeated, other capacity maintenance properties turned out to be outstanding. In addition, when the sintering temperature was $800\~850^{\circ}C$, the initial capacity was small but showed very stable cycle performance. According to EVS(electrochemical voltage spectroscopy) test, $LiFe_yMn_{2-y}O_4(y=0,\;0.05,\;0.1,\;0.2)$ showed two plateau region and the typical peaks of manganese spinel structure when the substitution amount of $Fe^{3+}$ increased, the peak value at about 4.15V during the charge-discharge process showed a tendency to decrease. From the previous results, the local distortion due to the biphase within the region near 4.15V during the lithium extraction gave a phase transition to a more suitable single phase. When the transition was derived, the discharge capacity decreased. However the cycle performance showed an outstanding result.

• 공업화학
• /
• 제4권2호
• /
• pp.423-431
• /
• 1993

Glycerol monostearate/POE(100) monostearate 혼합비이온계면활성제를 유화제로 사용한 O/W 에멀젼에 고급알코올인 1-hexadecanol/1-octadecanol 혼합물을 보조유화제로 첨가하여, 상거동 및 유동특성을 관찰하였다. 고급알코올의 결정구조가 변화하는 전이점은 1-hexadecanol/1-octadecanol의 조성에 따라 서로 다른 값을 가지며, 2/1의 비율에서 최저값을 나타내었다. 고급알코올의 첨가에 따라 에멀젼 내에는 액정이 형성되며, 이들로 인하여 에멀젼 입자간 응집체인 2차 입자가 형성되어 에멀젼의 점성도가 증가하였다. 에멀젼계의 온도가 고급알코올의 전이점 이하로 저하되면, 고급알코올의 지방족 사슬의 운동성이 제한된 겔구조가 형성되어 점성도가 증가하였으나 시간이 경과함에 따라 액정이 사라지고 에멀젼의 점성도도 저하되었다. 용액 내의 분산되는 양(본 실험에서는 2wt%) 이상의 고급알코올을 첨가해야 에멀젼 내에서 고급 알코올/계면활성제/물이 액정을 형성하였으며, 과량(본 실험에서는 10wt%)의 고급알코올을 사용하면 2차입자가 형성되지 않았다.

• 폴리머
• /
• 제39권3호
• /
• pp.480-486
• /
• 2015

조직과 장기 유착은 외과적 수술 후 부작용으로 자주 발생된다. 이러한 조직 유착을 방지하기 위하여 유착부위에 장벽을 형성하여 장기 유착을 방지할 수 있는 온도감응성 하이드로젤 유착방지제를 제조하고자 하였다. 폴록사머, 키토산과 표피성장인자를 가지고 온도감응성 키토산 하이드로젤을 제조하였다. 제조한 키토산 하이드로젤은 인체 내 온도와 유사한 $35^{\circ}C$에서 졸-젤 전이현상을 보였고, 1분 이내에 빠르게 젤화되었다. 키토산 하이드로젤은 표피성장인자를 7일 동안 천천히 방출하였고, 마우스모델에서 평가한 결과 조직 유착 방지를 효과적으로 하는 것을 확인하였다. 온도 감응성과 항균성을 갖는 키토산 하이드로젤이 장기 부착의 증가와 표피성장인자를 천천히 방출하는 유착방지제로서 유용하게 사용될 수 있다.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.201-205
• /
• 2012

The effects of various manganese precursors for the low-temperature selective catalytic reduction (SCR) of $NO_x$ were investigated in terms of structural, morphological, and physico-chemical analyses. $MnO_x/TiO_2$ catalysts were prepared from three different precursors, manganese nitrate, manganese acetate(II), and manganese acetate(III), by the sol-gel method. The manganese acetate(III)-$MnO_x/TiO_2$ catalyst tended to suppress the phase transition from the anatase structure to the rutile or the brookite after calcination at $500^{\circ}C$ for 2 h. It also had a high specific surface area, which was caused by a smaller particle size and more uniform distribution than the others. The change of catalytic acid sites was confirmed by Raman and FT-IR spectroscopy and the manganese acetate(III)-$MnO_x/TiO_2$ had the strongest Lewis acid sites among them. The highest de-NOx efficiency and structural stability were achieved by using the manganese cetate(III) as a precursor, because of its high specific surface area, a large amount of anatase $TiO_2$, and the strong catalytic acidity.