• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.2
• /
• pp.178-182
• /
• 2013

In mining and its similar industries, compact excavators are used commonly in narrow working spaces, of which bucket must be rotated essentially. Considering of those applications, many kinds of the compact excavators have been developed, but any stress evaluation of bucket rotating part had not been attempted. In this study, using of the finite element method and Spare solver, stress analysis has been performed on the bucket rotating parts and its adjacent parts of compact excavator, with using an excavation stress model, in various directions and positions. Resultantly, it has been defined that stress of connector in the rotating part is a little higher, due to its shape, than those remained parts of which stress are shown equally as 1 MPa. Especially in the moving parts, the stress of bucket pin and rotating pinion gear has been calculated as 7.7 MPa and 40 MPa respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.42 no.3
• /
• pp.134-147
• /
• 2006

A model experiment using circulation water channel was carried out to investigate the dynamic characteristics of bottom trawl net which can be used in sea mount of North Pacific. Hydrodynamic resistance and shape variation according to the flow velocity and angle of hand rope transformation for net were measured, and experimental value was analyzed as the value of full-scale bottom trawl net. The results summarized are as follows; At the $30^{\circ}$ of angle of hand rope to net, hydrodynamic resistance varied from 0.5kgf to 2.68kgf as the flow velocity increased between 0.31m/s and 0.92m/s, and formula of hydrodynamic resistance for the model net was $F_m=3.04\;{\cdot}\;{\upsilon}^{1.53}$. At the fixed angle of hand rope, Net height was low and Net width was high according to the increase of flow velocity, and in addition, vertical opening was low and Net width was high by the increase of angle of hand rope at the fixed flow velocity. At the $30^{\circ}$ of angle of hand rope to net, net opening area was $0.214m^2$ as flow velocity was 0.61m/s, and formula of net opening area for the model net was $S_m=-0.22{\upsilon}+0.35$. At the $30^{\circ}$ of angle of hand rope to net, catch efficiency seemed to be highest as $0.319m^3/s$ of filtering volume at the 0.76m/s(51kt's) of flow velocity. Shape variation of net showed the gradual laminar transform for the variation of flow velocity but there needed some improvements due to the occurrence of shortening at the ahead of wing net.

• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.92-100
• /
• 2015

Electric Vehicle (EV) can be categorized by the driving method into in-wheel and in-line types. In-wheel type EV does not have transmission shaft, differential gear and other parts that are used in conventional cars, which simplifies and lightens the structure resulting in higher efficiency. In this paper, design method for in-wheel motor for automobiles using Parameter Map is proposed, and motor with continuous power of 5 kW is designed, built and its performance is verified. To decide the capacity of the in-wheel motor that meets the automobile's requirement, Vehicle Dynamic Simulation considering the total mass of vehicle, gear efficiency, effective radius of tire, slope ratio and others is performed. Through this step, the motor's capacity is decided and initial design to determine the motor shape and size is performed. Next, the motor parameters that meet the requirement is determined using parametric design that uses parametric map. After the motor parameters are decided using parametric map, optimal design to improve THD of back EMF, cogging torque, torque ripple and other factors is performed. The final design was built, and performance analysis and verification of the proposed method is conducted by performing load test.

• Archives of design research
• /
• v.17 no.1
• /
• pp.383-392
• /
• 2004

The power tools is the product using working power generated by electric motor. Many companies are manufacturing numerous devices. Main features of tools are included various assembled products, small, light and solid and durable enough to match several standards. Fundamental requirements for the product is excellent performance and convenience for use. The quality of them depends on the equipped motor'(s) capability, accuracy of gear and endurance against worn-out. By adapting the state-of-the-art parts, they could be used in the place from home to heavy industry broadly. They can be classified electronic drills, grinders, saws and sanders families for the household appliances. For industrial tools, bore drill, grinder, polisher, and driver drill are classified as special and high priced group. This study presents the strategy of power tool development of BOSCH, BLACK&DECKER and KEYANG. Their products were analyzed in terms of product line and product mix concept. Then they are examined by design elements, such as color, shape and material for housing. As an analysis method, the image scale parameter and criteria were applied to each company's product.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.3
• /
• pp.209-216
• /
• 2002

How to estimate the shape of trawl net and ropes of a midwater trawl on full scale was described by implementing a three-dimensional semi-analytic treatment of a towing cable system with the field experiments obtained with the Scanmar system. The shape of trawl net from wingend to the beginning of codend was assumed to be of form $\chi$$^2$/ae$^2$+ y$^2$/be$^2$=(z - c)$^2$/c$^2$, and that of the ropes attached behind otter boards be of form yr = $A\chi$rB. In case of warp length 300m long, the volume of trawl net, the ratio of net height to net width at the mouth of the trawl net, and the inclination angle of float rope were estimated according to the change of towing speed. The volume and the distance between wingtips were increased with increasing towing speed. And the inclination angle of float (or ground) rope was slightly decreased with increasing towing speed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.247-254
• /
• 1991

Mackerel purse seine fishery is one of the most important fisheries in Korea and its annual mean catch from 1982 to 1988 is 350 thousand tons. Between 1982 and 1988, the characteristics of catch at 5 sectors of the sea area was analyzed according to operating sea block and the catch by fishes based on the data obtained from daily report of fishing condition that had been made out by 48 Korean fishing boats engaged in the fishery of purse seine. In these 5 sectors of the sea area, catch per net hauling in the coastal area of Cheju Island is less than that in the other sectors. Accordingly, the shape of fishing gear during operation has been measured to analyzed the deformation of net shape caused by the bottom current. (The lunar calender is used in the paper) The results obtained are as follows; The average CPUE of purse seines is 31.6 tons and it is higher from October to April than that from May to September. In the 5 purse seine fishing grounds, the ratio of net haul in the coastal sea area of cheju Island is 42.4% and it is the highest level, but the CPUE is 25.7 tons which is relatively low level. Each CPUE in the sea areas is significant differences with 1% level. Index of seasonal variation of mackerel CPUE from May to October is lower than the standard value, whereas index from November to January is higher. The diameter of circle by net shooting becomes shorter to the minimum caused by the bottom current during loose set, becomes narrower and the efficiency of fish encirclement becomes lower. The shape of leadline by bottom current becomes long oval type along with current direction in the tight set, while it becomes long oval type in the direction of a right angle to the current direction and the enclosed area is reduced hurriedly, and the deformation of net is most serious in the loose set.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.736-741
• /
• 2017

This paper examines the design for improving the wiper system of rotorcraft. During rotorcraft operation, the wiping performance and excessive clearance can decrease. The wiper system consists of a wiper arm assembly, motor, convertor and flex drive. If there is a problem with the wiper system, the operation ability decreases because the operation is restricted in a rainy environment. There are two main causes of the problem of the wiper system: the lifting forces acting on the wiper arm in aircraft flight and the excessive gap of the components. To remedy these two problems, the wiper arm was improved. The improvements included increased contact pressure on the wiper arm (spring tension), improved gear clearance, and material and shape changes. Durability test, aircraft ground test and flight test were carried out to verify the improved shape, and it was confirmed that the wiping performance and clearance problems were solved. Currently, the rotorcraft is operated without problem by applying the improved shape, and this design improvement process will be a useful reference for future rotorcraft development.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.2
• /
• pp.87-100
• /
• 2007

This study was carried out to offer fundamental data for improving the fishing efficiency of the Danish seine. The net height and the shape in the water was measured to analyze the efficiency of the existing Danish seine. And then, an improved fishing gear was developed based on the results and was tested in the field. Measuring devices were attached on center of a ground rope and a head rope. The net height is the spread distance between the ground rope and the head rope, which was measured on the different ratio of buoyancy. The results are obtained as follows. The net height estimated from the design plan of horizontal hanging ratio 0.40 in the existing Danish seine A and B estimated both 4.94m. The net height of the existing Danish seine A and B was respectively 1.8m and 2.3m, which form 36.4% and 46.2% of the net height estimated from the design plan. Buoyancy was changed as 79.5% and 96.2% relative to the sinking force in the existing Danish seine. The net height of 79.5% was 3.95m which increased to 80% of the estimated net height. The other shows the same result with the first case. It is not necessarily that the high buoyancy/sinking force ratio make the high net height, 80% is adequate as the buoyancy/sinking force ratio. In case of the improved Danish seine, the mean net height was about 5.0m, means 58.3% of estimated net height 8.58m.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.5
• /
• pp.41-49
• /
• 2005

This paper discusses the test procedure, instrumentation, verification methodology and the results of the ground vibration test(GVT) performed on the KF-16D aircraft to estimate experimentally dynamic characteristics of the aircraft. The modal tests for 7 external store configurations were conducted to estimate effects of external stores on the aircraft vibration modes. To emulate free-free boundary conditions the test aircraft was mounted on its landing gear structure with deflated tires during the GVT. The airframe modal tests were done by burst random excitations with 6 to 8 shakers and about 200 accelerometers. Frequency response functions(FRFs) were measured for each test, and the FRFs were reduced and analyzed to identify the dynamic parameters interested. The analyses were carried out in two steps. To extract modal parameters such as, frequencies and damping ratios, the poly-reference least square complex exponential method was used in the time domain. The mode shape coefficients were estimated with the least squares frequency domain method to identify the vibration modes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.318-327
• /
• 2012

The operating sound radiated from a laser printer includes tonal noise components caused by the rotating mechanical parts such as gear, shaft, motor, fan, etc. The negative effects of the tonal noise components need to be considered in the process of developing a sound quality index for the quantitative evaluation of the emotional satisfaction in terms of psycho-acoustics. However, in a previous paper, it was confirmed that the Aures tonality did not have enough correlation with the results of jury evaluation. The sound quality index based on loudness, articulation index, fluctuation strength has a little problem in considering the effects of rotating mechanical parts on the sound quality. In this paper, to solve the tonality evaluation problem, the calculation algorithm of Aures tonality was investigated in detail to find the cause of decreasing the correlation. The new tonality evaluation model was proposed by modifying and optimizing the masking effect, loudness ratio, and shape of weighting curve based on the basic algorithm of Aures tonality, and applied to two kinds of operating sound groups in order to verify the usefulness of proposed model. As a result, it is confirmed that the proposed tonality evaluation model has enough correlation and usefulness for expressing the tonalness in the operating sounds of laser printers. In the following paper, this results will be used to model the sound quality index as the input data by using the classification algorithm.