• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.259-263
• /
• 1996

In diagnosing of mechanical machinery, it is often improtant to get information about the movement inside the machine casing. If the values of internal tities may be derived from the measurement using sensors installed on the external casing, it would be much better in many senses. This paper discusses extracting internal gear movements byfrequencydemodulation from gear meshing force signatures which can be recovered from the vibrations though inverse filter. There are several way in demodulating signals. In this paper, especially, Hibert Transform, Wigner-Ville distribution, and Teager energy operator are examined and compared. Effects of noise on the frequency demodulation methods and the behavior of bandpass filtered noisy signal are discussed using simulated time-varying frequency signals.

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.504-512
• /
• 1998

For analyzing the torsional vibration of a multiple stepped gear system containing a pair of triple gears, a transfer matrix model based on Hibner's branch method is developed and the natural properties of the branched rotor system are calculated with using the $\lambda$-matrix formulation. A Campbell diagram, in which the excitation sources caused by the mass unbalances of the rotors and the transmitted errors of thegearings are considered, shows that, at the neighborhood of the operating speed, there are the four critical speeds amplifying the first mode and the fifth mode. For the surpression of the gear box vibration, two ways are suggested by referring the mode shapes.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.5
• /
• pp.17-21
• /
• 2010

A volumetric gear pump is often used in extensive industrial applications to provide both high pressure and sufficiently high flow rate by physical displacement of finite volume of fluid with each revolution. To better understand the unsteady flow characteristics within the pump, numerical simulations were conducted by using moving dynamic meshing (MDM) techniques in commercially available CFD software, FLUENT. The effects of rotor clearance size and rotational speed of rotor on the flow characteristics, specially the temporal variation of velocity and pressure field, which is a main source of flow noise, was investigated. The results showed that significant reverse flow is developed in the rotor clearance and that its size is one of the most important factors affecting flow characteristics and pressure pulsation.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.173-179
• /
• 1995

This paper descrived housing design in conception of dynamic characteristics. The vibration and noise in power train system of automobile are important on the environment matter. The vibration caused by meshing teeth of gear is transmitted to the gear box faces through shafts and bearings. Shape of housing is used different radius of curvature(R=0 to 80 mm). The velocity responese, sound power and radiation efficency on the surface of gear box are calculated. The sound power and radiation efficency are compared with different radius of curvature.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.2
• /
• pp.113-122
• /
• 2020

Noise affects the accuracy of three-dimensional shape recovery. Its occurrence is unpredictable and depends on several mechanical, environmental, and other factors. When two-dimensional image sequences are obtained for shape from focus (SFF), mechanical vibration occurs in the translational stage, causing an error in the three-dimensional shape recovery. To address this issue, mechanical vibration is modeled using Newton's second law and the principle of the rack and pinion gear. Then, an optimal sampling step size considering the mechanical vibration is suggested through theoretical demonstration. Experiments conducted with real objects verify the effectiveness of the proposed sampling step size. In this paper, in a realistic environment with noise, the potential of obtaining more accurate three-dimensional reconstruction results of the objects is explored by acquiring the optimal sampling step size, which improves the sampling step size relative to those reported in a previous study performed under similar conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.11
• /
• pp.838-844
• /
• 2003

The noise and vibration reduction schemes of an industrial robot are studied. Experimental procedures are employed to examine the sources of robot noise. A parametric study is undertaken to observe the effects of each part such as gear, shaft and housing on the sound pressure level. After the part which mainly effects on the noise is proved, we propose countermeasures for reducing the noise and vibration of the robot system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.935-938
• /
• 2007

In suction nozzle of a vacuum cleaner, where flow-induced noise is generated mainly by flow resistance, several ideas to reduce noise are investigated. To increase fan performance, blade number is optimized and a centrifugal fan is replaced by a cross-flow fan, In addition, gear ratio of fan to drum brush is changed. It is found that fan performance is increased by adopting these methods. Next, the blade height of the fan is decreased to reduce sound pressure level, which causes inevitably decrease in fan performance. Eventually, flow-induced noise is reduced by 6.3 dBA in its overall level with the fan performance maintained.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.119-124
• /
• 2000

The 3-stage centrifugal compressor is used in order to measure the noise spectra of compressor, and analyze the results. Two cases are investigated for compressor noise components. Case I includes total system such as compressor, inter-cooler, motor, and Case II excludes cooling system. BPF tonal noise is important in compressor, and cooling system including inter-cooler contributes to broadband noise. Also, motor, gear box, and motor cooling fan are the second contributions to total compressor noise. Centrifugal compressor flow-field is calculated using two-dimensional grid and Navier-Stokes equations. Static pressure increases, and total pressure decreases, as air passes through the compressor components.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3633-3640
• /
• 2010

For a development of non-contact magnet gear which is magnetized as a helical shape, a method of 3-dimensional FEM analysis is used. An elementary technique required for magnetic property analysis and parts design about magnet gear is ensured. In order to test a performance of clean conveyor and turning device which is composed with magnet gear, a clean class 10 environment booth is used for a trial test. It is verified that the magnet conveyor can be acceptable under a condition of clean class 10 by a result of trial test about transfer speed, maximum torque permission, cleanness, maximum transfer weight, existence of hunting and degree of noise.

• Tribology and Lubricants
• /
• v.29 no.6
• /
• pp.397-402
• /
• 2013

This study examined the tribological characteristics of the drive shaft and axle system in vehicles. The first drive shaft example contained end play for a CV joint that transferred part of the transmission power to the wheel. The joint part of the drive shaft was deformed because of reduced durability due to wear. Thus, vibrations caused the body to shake and become unbalanced when the drive shaft transferred the power. The second example was the cross-section of a shaft that connected the slip-connection of the propeller shaft on the input side to the yoke flange of the output side; the durability was reduced because of corrosion. End play caused by wear between the bearing and cross-section shaft appeared to cause shaking. In the third example, a grease leak reduced lubrication and thus caused damage to the hub bearing and inside the knuckle. The failure was produced by sticking. The fourth example had noise produced by the gear and gear transfer. This was due to the backlash of the pinion and few ring gears for the differential gear. Therefore, drive shaft and axle systems must be thoroughly checked and managed to minimize and reduce failure phenomena.