• 한국생산제조학회지
• /
• 제24권3호
• /
• pp.320-326
• /
• 2015

Despite the wide industrial applications of planetary gear trains, the relationship between the design parameters (tooth profile, carrier mass, etc.) and performance (strength, vibration, noise, etc.) remains poorly understood. A significant amount of research has focused on transmission errors, which are measurable performance indicators directly related to the design parameters. Herein, an experimental test rig for a single-stage planetary gear set built using digital angular encoders and gap sensors is described. To study the static and dynamic characteristics of this planetary gear train, the transmission errors and sun gear orbit are analyzed from the data measured under various levels of torque and speed. The transmission errors of the gear train decrease 40% when the speed increases from 30 to 600 rpm with an output torque of 39.2 Nm, and increase 22% when the output torque increases from 19.6 to 39.2 Nm with an input speed of 30 rpm.

• 한국소음진동공학회논문집
• /
• 제25권12호
• /
• pp.815-821
• /
• 2015

Maritime safety has been more critical recently due to the occurrence of shipboard accidents involving prime movers. As such, the propulsion shafting design and construction plays a vital role in the safe operation of the vessel other than focusing on being cost-efficient. Smaller vessels propulsion shafting system normally install high speed four-stroke diesel engine with reduction gear for propulsion efficiency. Due to higher cylinder combustion pressures, flexible couplings are employed to reduce the increased vibratory torque. In this paper, an actual vibration measurement and theoretical analysis was carried out on a propulsion shafting with V18.3L engine installed on small car-ferry and revealed higher torsional vibration. Hence, a rubber-block type flexible coupling was installed to attenuate the transmitted vibratory torque. Considering the flexible coupling application factor, reduction gear stability due to torque variation was analyzed in accordance with IACS(International Association of Classification Societies) M56 and the results are presented herein.

• 한국소음진동공학회논문집
• /
• 제22권12호
• /
• pp.1172-1183
• /
• 2012

Aure's tonality was considered as the sound metrics for the expression of the tonality of gear whine sound in a previous research. It was failed to use the Aure's tonality as a sound metric for the tonal impression. Thus Aures's tonality, was developed for tonal impression in previous research. However, this metric did not express well the tonality of gear whine sound since the whine sound is a non-stationary signal with frequency modulation and amplitude modulation. In this study, the new method for the tonality evaluation for a non-stationary signal is presented. It is developed based on the prominence ratio, tonality impression function, and lower threshold level. It improves the accuracy and reliability of the sound quality index being used for the sound quality evaluation of the axle-gear whine sound.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권8호
• /
• pp.1057-1067
• /
• 2010

다단 기어연쇄, 베어링, 축, 로터로 구성되는 함포용 synchro system의 구동장치를 개발하기 위하여, AGMA규격에 의한 기어 굽힘강도, 면압강도해석, 기어치형설계를 포함한 정적설계를 수행하였다. 또한 전달행렬법을 효과적으로 적용시킬 수 있는 Hibner's branch법과 자유도가 큰 경우에도 계산 오차 없이 고유특성치를 빠뜨리지 않고 산출할 수 있는 ${\lambda}$-matrix법을 도입하여 함포용 Synchro system의 좌우 선회용과 상하 고각형의 위험속도 해석 및 평가를 하였고, 운전속도 범위 내에 위험속도가 존재하지 않았다.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.71-76
• /
• 2019

The differential planetary gear reducer as a main component of the concrete mixer driving mechanism requires a strong torque to mix concrete compounds. As this component is currently dependent on imports, it is necessary to develop it by conducting a study on vibration analysis and the resonance problem. The noise and vibration of a concrete mixer reducer increase owing to the transmission error of planetary gears, and the damage of components occurs owing to the problems in design and production. In this study, the tooth-passing frequency is calculated to evaluate the noise and vibration of a mixer reducer, and a fast Fourier transform (FFT) analysis is conducted through a vibration test using an acceleration sensor. The vibration of the reducer is measured at three points of input and output of the shaft and planetary gear housing with fixed and variable revolutions per minute. The operating conditions of gears and bearings are evaluated by performing the FFT analysis, and the resonance problem is verified. The results show that No. 1 pinion and ring gears revolve disproportionately. The amplitude values appear high, and the wear of tooth faces occur in tooth-passing frequencies and harmonic components of No. 1 and No. 2 pinion-ring gears. Therefore, we conclude that design changes in the reducer and a correction of tooth profiles are required.

• Journal of Biosystems Engineering
• /
• 제31권4호
• /
• pp.323-333
• /
• 2006

Introduction of a direct engine-PTO driveline to agricultural tractors has reduced production cost and increased transmission efficiency of the PTO driveline. However, this type of PTO driveline has caused a severe rattle noise in the PTO gearbox under idle conditions. This study was conducted to investigate the causes of the rattle noise and the effects of driveline parameters on it. A mathematical model was developed for a direct engine-PTO driveline. The model was proved experimentally to be accurate enough to simulate the dynamic characteristics of the PTO driveline motions. The simulation study showed that the rattle noise was caused by collisions between the driving and driven gears in the PTO gearbox due to velocity variation of the gears, which was induced by torque fluctuations from the engine. It was also found that the rattle noise decreased with the drag torque and mass moment of inertia of the engine flywheel. Smaller mass moment of inertia of the driven gears and backlash also reduced the rattle noise. However, increasing the drag torque and mass moment of the engine flywheel or decreasing the backlash and mass moment of inertia of the driven gears were limited practically by their detrimental effects on transmission efficiency, gear strength and smooth meshing of the gears.

• 대한기계학회논문집A
• /
• 제38권3호
• /
• pp.295-302
• /
• 2014

내접형 기어펌프의 경우 내구성과 소형화의 장점을 가지고 있으나, 유량증대 및 소음저감의 성능개선이 요구되고 있다. 본 논문에서는 외부로브 형상이 다양한 곡선 조합(타원 1-인볼루트-타원 2)인 경우에 대하여 기구학적 치형 형상 관계식을 유도하고, 창성된 치형에 대해 소음에 관계된 성능인자(압력각, 유량맥동과 미끄럼률)를 예측하여 소음정도를 수치적으로 비교하였다. 또한 이론 해석을 통해 구한 치형형상과 성능인자 예측 알고리즘을 통하여 설계변수와 성능인자간의 영향도를 분석하였고, 분석 결과를 바탕으로 일정한 유량성능을 유지하면서 소음이 저감된 치형의 최적설계를 수행하였다. 해석결과를 바탕으로 제시된 치형의 최적설계에 대한 시제품 제작 및 소음 시험을 통해 설계의 타당성을 검증하였다.

• International Journal of Automotive Technology
• /
• 제7권4호
• /
• pp.477-483
• /
• 2006

A vibration model of a helical gear pair for vehicle transmission is developed by considering the elastic deformation of the active teeth and the body to be a rigid. The main source of vibration in a helical gear system which caused by the mass unbalances of rotors and the transmission errors of gearings in mathematically formulated and applied to the analysis of vibration characteristics of geared systems. As an example, a simple geared system containing a helical gearing is considered. The critical speeds are found by the Campbell diagram and compared with the experimental results We expect this developed program to contribute to the reduction of the vibration and noise on vehicle a transmission in the field of both design and manufacturing. In addition, this program can be used as a basic program for CAD/CAM of low-noised gear teeth.

• 한국정밀공학회지
• /
• 제27권11호
• /
• pp.84-91
• /
• 2010

Heat treatment with carburized quenching process is widely used for automotive helical gear to improve its surface properties of hardness and strength. However, the gear can be deformed with the process over the allowable tolerance, which possibly makes noise, vibration and heat problems in operation. In this study, deformation of helical gear during heat treatment of carburized quenching was analyzed with a numerical method, incorporating coupled calculations of thermal conduction, carbon diffusion, phase transformation and thermal stresses. With the analysis, the effect of coolant temperature in quenching on the deformation was investigated. The result of the analysis revealed that the higher the coolant temperature became, the more change of helix angle and the more compressive stresses in the surface generated, because of delayed generation of martensite in the part.

• 한국자동차공학회논문집
• /
• 제3권2호
• /
• pp.30-41
• /
• 1995

Gear rattle is a source of vibration and noise in automotive gearbox casing and generally occurs at or near system resonant frequencies. The neutral gear rattle of the gearbox. is affected by the stiffness and hysteresis torque in the clutch disk and drag torque determining balancing point of the clutch disk operating range. The experiment is carried out in the pre-damper type clutch and a manual transmission of a automobile equipped for inline four-sylinder four-cycle 1.5L MPI engine and the computer simulation is executed by 5th order Runge-Kutta method. The results of the simulation analysis and experimental studies show the dynamic behavior of clutch and a phenomenon of the neutral gear rattle with respect to drag torque and torsional characteristics of the clutch.