• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.163-173
• /
• 2014

In this study, a modeling method is based on representing a road generation system with several rigid bodies, i.e, pad, shaft, torsional damper, oneway-clutch, gear system, and electricity generator. The simulation software is developed to evaluate the performance of a road generation system. It is used to determine parametric dimension for optimal design with the theoretically calculated results from the simulation software. The parametric dimensions are included as capacity, length, and angle of equipment. The transient responses at the conditions of low and high vehicle speed are compared with the calculated results as torque, power, out energy etc. Consequently, before manufacturing system, the analysis of simulation results shows that the proposed concept and system has efficiency and confidence.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.74-84
• /
• 2017

This paper presents the development of the underwater cleaning robot platform for a higher efficiency in manufacturing industry. Human operators directly go into the cistern and clean sludge after drainage of the water so far. It is sometimes dangerous because of the harmful chemical materials from the product making process. In addition, it takes long time for water drainage and supplying it back. However, the robot cleaning operation does not need to drain water so that it could be applied to the sludge cleaning work at any time without the plant pause. Moreover, it can prevent the safety accidents because human operators are not necessary to enter directly the sludge cisterns. This paper shows the performance of cleaning work that can be applied in the industrial field through the design and development of underwater cleaning robot platform. And these results demonstrate that the developed underwater cleaning robot has great possibilities to clean other industrial water cisterns.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.3
• /
• pp.207-216
• /
• 2016

A gerotor is suitable for miniature manufacturing because it has high discharge per 1 cycle and a simple structure, while also being widely used for lubrication oil of engines and as a hydraulic source of automatic transmission. In the automobile industry, improvements in fuel efficiency and noise reduction have recently come to the fore. It has also been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency through optimal gerotor and port shape design. In this study, to develop an optimal gerotor with a new lobe shape, 2-ellipses-combined, the equation of the lobe shape was derived, and CFD analysis results were compared for 2-ellipses with those of the previous gerotors (3-ellipses and ellipse1-involuteellipse2). A performance test for the oil pump with the optimal rotor (2-ellipses) was carried out and showed good agreement with the results obtained from CFD analysis.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.841-848
• /
• 1999

In the quality assurance check process of DC motor systems, even though the overall sound pressure level is acceptable, there is an incident that subjective evaluation leads to failure in product quality due to annoying noise. This kind of problem may be originated from the manufacturing or assembly process. In this paper, the transient spectral analysis, or the time-frequency analysis is applied to the noise quality problem. For the case study, the cause of annoying noise in the wind shield wiper motor is experimentally analyzed in detail. It is concluded that the defect in the shaft causes the impact noise which is not detectable by steady spectral analysis. Also demonstrated is how the time-frequency analysis is effectively applied to the annoying noise identification of the rotor-gear system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.399-402
• /
• 2006

The outer race of CV(constant velocity) joint is an important load-supporting automotive part, which transmits torque between the transmission gear box and driving wheel. The outer race is difficult to forge because its shape is very complicated and the required dimensional tolerances are very small. Traditional warm and cold forging methods have their own limitations to produce such a complex shaped part; warm forging requires complex system with relatively higher manufacturing cost, while cold forging is not applicable to materials with limited formability. Therefore, multistage forging may be advantageous to produce complex shaped parts. In order to build a multistage forging system, it is necessary to characterize mechanical properties in response to system design parameters such as temperature, forging speed and reduction. For the analysis of formability of multistage forging process, finite element method(FEM) has been used for the process analysis. As a model case, a constant velocity (CV) joint forging process is analyzed by FEM, since CV joint has a complex shape and also its required dimensional tolerances are very tight. The data acquired by FEM is compared with operational forging data obtained from an industrial production line. Based on this comparative analysis, multistage forging process for CV joints is proposed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.4
• /
• pp.8-14
• /
• 2006

The important function of Ball-Stop part is to operate power shift using suitable pneumatic force for vehicle with more than 5 ton when a driver changes gear. In this paper, we have applied the concept of the DFSS(Design for Six Sigma) to robust design of Ball-Stop part. First, we have found the control factors which could mainly influence the performance of the Ball-Stop part. The simulations of contact between head and detent pin was performed to evaluate effect of control factors according to DOE(Design of experiment) by using $ADAMS^{(R)}$. Finally, we have obtained optimal levels of each factors using $MINITAB^{(R)}$. Through the comparison of the result of optimized design with one of inintial design, we have verified the usefulness of DFSS method which can be applied to robust design of mechanical systems.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.154-160
• /
• 2002

Powder metallurgy(P/M) process has been used for the production of high performance high-speed steels. P/M high speed steel has more uniform and fine microstructure than those of conventional wrought products. Therefore, it offers distinct advantages over conventional tool steels. The superior uniformity of composition and fine microstrucure lead to excellent toughness and less distortion during heat treatment, which in turn can reduce total grinding costs and provides other benefits, such as uniform hardness and increased tool life. From these reasons, milling, hole machining, broaching, and gear manufacturing tools are major applications of P/M high-speed steels. In this research, we evaluated tool wear of flat endmill which is made of P/M high-speed steel from the view point of cutting tool performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.11
• /
• pp.927-935
• /
• 2016

A gerotor is suitable for miniature manufacturing because it has a high discharge per cycle and a simple structure, while also being widely used as lubrication oil of engines and the hydraulic source of automatic transmission. In the automobile industry, it has been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency through optimal gerotor design. In this study, to obtain an optimal gerotor with an ellipse-elliptical involute-ellipse combined lobe shape, an automatic program was developed for calculating performance parameters and drawing a gerotor profile. An oil pump was assembled with the optimal gerotor together with the port used at the actual field and CFD analysis was performed on this assembly using Ansys-CFX. A performance test for the oil pump was carried out and showed good agreement with the results obtained from the theoretical analysis and the CFD analysis.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.5
• /
• pp.41-48
• /
• 2005

The Rotating transmission is made up of belts, mass disks and gears. This transmission is controlled electro-mechanically by the motor and operation program. The control strategy of the system can be to change belts' stiffness and the masses of mass disk and gear. This system can be modeled as a rigid body, and also finds broad application in such diverse fields as machine tools, the cruise control system In automobiles, and control in the attitude and gimbals of spacecraft. This Transmission proves the necessity and effect of a closed loop control. The study of the Rotating Transmission excited by its base motion is able not only to predict the rotational performance, but to obtain the fundamental data for vibration isolation. In this research, we compared the response characteristics of the two controllers by means of the experiments on PD controller and PID controller added on integral action. Furthermore, we studied the response abilities such as steady state error, overshoot, and ect. and the response velocities such as rising time, settling time, and ect. in the rotating transmission.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.7
• /
• pp.657-664
• /
• 2011

This paper shows a whole noise quality checking system for the new developed 6th speed automatic transmission manufactured in USA. Due to demand for manufacturing of the high NVH quality transmissions in the mass product line, some special checking system called EOL NVH is adapted. This EOL system is using vibration sensor and analysis technologies. Through adapting vibration analysis technologies and functions likewise RMS, crest factor, harmonics, peak, band and order tracking, various noise problems caused by wear, nick and deformations could be successfully detected and predicted. Therefore, automatic transmissions manufactured in the USA could get high NVH quality. The developing process described in this paper and results on EOL system will offer good guides to the engineers who built the next transmission factory.