• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.142-147
• /
• 2011

Compressed natural gas (CNG) is well known as one of the cleanest burning alternative fuels. Bi-fuel CNG vehicle can also run on gasoline or another fuel while dedicated natural gas vehicle is designed to run on natural gas only. Recently, increased attention has been focused on bi-fuel CNG/LPG taxi because of good fuel economy of CNG. A number of LPG taxis modified to CNG Bi-fuel vehicles are running in many cities. In this paper, the emissions characteristics of in-use passenger cars running on CNG and LPG were investigated. Chassis dynamometer test was used to measure exhaust emissions from an in-use fleet of 5 cars. Exhaust emissions were collected for CVS-75 driving mode. The test results showed that for CNG fuel mode, CO, $CO_2$ and NMHC emissions decreased to 9%, 12% and 14% respectively, and $CH_4$ and $NO_x$ emissions increased to 317% and 47% respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권3호
• /
• pp.351-359
• /
• 2010

Bi-fuel system in a spark ignition engine (SIE) is a rising phenomena in today's automobile technology. In a gasoline driven vehicle, alternatively adoption of compressed natural gas (CNG) could be used as a potential substitute to meet the energy requirement and this is possible by some minor changes in the hardware of the existing engine. Gasoline engine is widely used in the passenger cars, light, medium and heavy duty vehicles but the consumption status of the petroleum is decreasing worldwide and at the same time environmental pollution from automobiles is seriously establishes as a threat for every nation in respect to global warming and climate changes. Now-a-days most vehicles operate using CNG for its popularity stems, clean burning properties and cost effective solution compared to other alternative fuels. It refers as a good gaseous fuel because of its high octane number and self ignition temperature. Though the power output is slightly lesser than the gasoline fuel; its thermal efficiency is better than the gasoline for the same SIE. The research paper highlights the reduction of CO, reasonable outcomes of HC emissions with minor increase in $NO_x$ emissions compared with the gasoline fuel to bi-fuel mode in the SIE that meets the emission challenges.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2008년도 추계학술대회 논문집
• /
• pp.142-144
• /
• 2008

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.680-685
• /
• 2006

The latest trend in the automotive industry demands the development of high stiffness car bodies and the securement of inter-system performance for low vibration and noise vehicles. This demand, however, conflicts with need for light weight design and greater fuel efficiency, thus raising the importance of optimization design to satisfy both developmental goals. We chose two European medium sedans, which has gasoline engine and diesel one, to elucidate the noise characteristics of diesel passenger cars, whose sales have been increasing in both Korea and Europe. In the present study a systematic experiment was conducted to analyze the noise characteristics in diesel cars. we made it possible for differentiating car management according to customer demand while allowing for improved commercial feasibility. it was possible to improve interior noise by 2 dB(A) on average sound pressure level. As a result, by 4% higher on articulation index(AI).

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.527-534
• /
• 2006

Modern passenger cars with diesel engines are equipped with DOC(diesel oxidation catalyst) for the purpose of reducing HC and CO in the exhaust stream. Cold start exhaust emissions pose troubles here as on gasoline engine vehicles. As a result, some of the diesel passenger cars roll off todays the assembly lines with WCC(warm-up catalytic converter). Oxidation characteristics of the particulates in WCC is analyzed in this study by EEPS(engine exhaust particulate size spectrometer). The maximum number of PM is found to come out of WCC in sizes near 10nm when an HSDI diesel engine is operated under the conditions of high speed and medium to heavy load. When the temperature of the WCC exceeds $300^{\circ}C$, the number of PM smaller than 30 nm in diameter sharply increases upon passing through the WCC. Total mass of emitted PM gets reduced downstream of the WCC under low speed and light load conditions due to adsorption of PM onto the catalyst. Under conditions of high speed and medium to heavy load, the relatively large PM shrink or break into fine particles during oxidation process within the WCC, which results in more mass fraction of fine particles downstream of the WCC.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.11-16
• /
• 2001

In the DI diesel engine of passenger cars, common rail injection system have been used to improve the engine performance and reduce the exhaust emission by controlling injection timing, injection pattern, and injection duration. In case that common rail injection system is applied to high speed DI diesel engine, it is necessary to have high response and good repetition characteristics. These characteristics of injector depend on the characteristics of solenoid. Thus, to apply the common rail injection system in the high speed diesel engine, we had designed and made a multi-pole solenoid, and carried out repetition, response test to compare the multi-pole solenoid with the gasoline Injector solenoid. The result shows that repetition and response characteristics of multi-pole solenoid have better characteristics than the gasoline injector solenoid.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.58-64
• /
• 2007

As the concerns regarding global worming were increased, the pressure of greenhouse gas(GHG) emission reduction on mobile source was also increased. Carbon dioxides contribute over 90% of total GHG emission and the mobile source occupies about 20% of this $CO_2$ emission. Therefore automotive exhaust is suspected to be one of the major reasons of the rapid increase in greenhouse effect gases in ambient air. In this study, in order to investigate $CO_2$ emission characteristics from gasoline passenger cars(PC), which is the most dominant vehicle type in Korea, 106 vehicles were tested on the chassis dynamometer. $CO_2$ emissions and fuel efficiency were measured. The emission characteristics by displacement, gross vehicle weight, vehicle speed and CVS-75/vehicle speed mode were discussed. Test modes were vehicle speed modes and CVS-75 mode that have been used to develop emission factors and to regulate for light-duty vehicle in Korea. It was found that $CO_2$ emissions showed higher large displacement, heavy gross vehicle weight, low vehicle speed and CVS-75 mode than small displacement, light gross vehicle weight, high vehicle speed and vehicle speed mode, respectively. From these results, correlation between $CO_2$ emission and fuel efficiency was also determined. The results of this study will contribute to domestic greenhouse gas emissions calculation and making the national policy for climate change.

• 공업화학
• /
• 제25권2호
• /
• pp.222-226
• /
• 2014

본 연구에서는 도시대기 중 문제시 되는 미세먼지 배출원의 주범으로 추정되는 유류를 사용하는 도로배출원(자동차)의 배출량 산정을 위한 배출계수 및 활동도 적용의 타당성과 미세먼지 제어를 위한 법제도 시행의 타당성에 대하여 분석하고 고찰하는 것을 연구의 목적으로 하였다. 실제 교통량에 근거하여 작성한 본 연구의 자동차 배출량 공간분석 결과와 기존 방법과의 차이가 나타났는데, 대기 미세먼지 농도를 알아보기 위한 대기분산모델링을 수행할 때 현실적이지 않은 배출량을 입력할 경우, 농도분포 결과의 심각한 왜곡을 초래할 수 있기 때문에 자동차 배출 미세먼지 공간분석은 실제 교통량에 근거하여 작성해야 할 것이다. 국립환경과학원방법(2010)에 사용된 자동차 미세먼지 배출계수는 주로 2003~2007년식의 자동차를 대상으로 하였기 때문에 DPF 장착 등의 효과를 반영할 수 없었고, 서울 인근 도로 노선별 자동차 미세먼지 배출량 산정결과 국립환경과학원방법과 본 연구방법의 결과가 상이하게 나타났는데, 승용차 배출량 중 휘발유차 배출량이 디젤차량 배출량과 대등하게 산정되었기 때문에, 현실에 맞는 디젤 및 휘발유 자동차 미세먼지 배출계수 개발이 필요하다.

• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.785-791
• /
• 2000

GDI (Gasoline Direct Injection) engines are considered as one of the candidates for next generation engines of passenger cars, which reduce exhaust emissions and fuel consumption. In GOI engines, a high-pressure gasoline supply system is required to directly inject the fuel to combustion chambers. Because of low lubricity of gasoline fuel, the clearance between a plunger and a barrel in GDI fuel pumps is too wide to achieve smooth hydrodynamic lubrication. Thus, it is difficult to generate high-pressure condition in GDI fuel pump since large amount of leakage flow occurs between the plunger and the barrel In this study, an optimum plunger design is presented to minimize leakage in the aspect of flow control. This paper analyzes leakage flow characteristics in the clearance to improve pumping performance of GDI fuel pumps. Effects of groove in the plunger are studied according to variations of depth and width. Evaluations of pumping performance are determined by the amount of pressure drop in the leakage path assuming a constant leakage flows. Both of turbulence and incompressible models are introduced in CFD (Computational Fluid Dynamics) analysis. Design parameters have been introduced to minimize leakage in limited space, and a methodological study on geometrical optimization has been conducted. As results of CFD analysis in various geometrical cases, optimum groove depths have been found to generate maximum sealing effects on gasoline fuel between the plunger and the barrel. This procedure offers a methodological way of an enhancement of plunger design for high-pressure GDI fuel pumps.

• 한국대기환경학회지
• /
• 제9권4호
• /
• pp.320-328
• /
• 1993

Gaseous pollutants in Namsan Nos. 1, 2, and 3 tunnels and Pukak tunnel were measured along the road by an air-monitoring van from the evening of February 9 to the morning of February 12 in 1993. Average concentrations of pollutants in Namsan tunnels were 9.2-13.5 ppm CO and 0.037-0.047 ppm SO$_{2}$. Average concentrations of SO$_{2}$ in Pukak tunnel was 0.79 ppm, higher than those in Namsan tunnels, due to the traffic of heavy-duty buses and trucks. The pollutant concentrations in Namsan tunnesl could be explained by emission of passenger cars using unleaded gasolin and LPG taxies. Average concentration of NO$_{x}$ in Namsan tunnels was at least 1.1 ppm, estimated from the emission factor of pasenger cars using unleaded gasoline. Pollutant concentrations in Namsan No. 3 tunnel were higher at the exit because of the piston action of air mass in the tunnel provided by the traffic. Fans installed at Namsan and Pukak tunnes could be useful, but their flushing action of ambient air in the tunnel was not clearly observed.d.