• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.170-177
• /
• 2006

Hydrogen can extend the lean misfire limit to a large extent when it is mixed with conventional fuels for a spark ignition engine. In this study, hydrogen-enriched gaseous fuels by reforming process were simulated according to their proportions of $H_2$, CO, $CO_2$ and $N_2$ gases. Pure hydrogen and two different hydrogen-enriched gaseous mixtures(A-, B-composition) were tested for their basic effects on the engine performances and emissions in a single cylinder research engine. A- and B-composition showed different results from 100% $H_2$ addition because air/fuel mixtures were more diluted by their additions. Even though the energy fraction of reformed gases was increased, combustion stabilities and lean misfire limits were not sensitively improved. It means that combustion augmentation by $H_2$ addition was offset by the charge dilution of $N_2$ and $CO_2$. In addition, the low flammability of CO gas deteriorated thermal efficiencies. CO emission was drastically increased with B-composition which included higher CO component. However, $NO_x$ was reduced as energy fraction($X_e$) rised except for the case of 100% $H_2$ addition at $\lambda=1.2$ and was, for A-composition, lowered to a factor of ten when compared with that of $H_2$ addition. HC emissions were largely influenced by $COV_{imep}$ due to misfire and partial burns.

• 전기학회논문지
• /
• 제57권12호
• /
• pp.2199-2201
• /
• 2008

Sulfur hexafluoride($SF_6$) is a gaseous dielectric used in high voltage electrical equipment such as an insultor or arc quenching medium in the transmission and distribution of electricity. however, $SF_6$ is one of the greenhouse gases(GHG) with a global warming potential that is 23,900 times greater than that of carbon dioxide($CO_2$). for this reason, $SF_6$ emissions in electric equipment shall be controlled to reduce GHG and improve cost-effective use of $SF_6$ for economical benefits. Until recently there has not been any investigation on $SF_6$ emission characteristics and inventory in Korea. To understand emission characteristics during the use-phase, the scope of this study was limited to the following closed pressure system equipment from 10 substations in Korea. This study highlights (1) the investigation of sampling/analysis methodology for $SF_6$ emissions in high voltage equipment, (2) the estimation of $SF_6$ emissions in the use-phase, and (3) the comparison between the emission ratio and the mass-balance applied to inventory study. According to this study, the majority of emissions were related to electric equipment nameplates and the rest of the emissions were related to the handling of $SF_6$ during operations. from this result, emission ratios estimated from this study were similar; GIS was 14% and GCB was 13%, as maintenance process conditions were the same as manual process conditions for both equipment.

• Asian Journal of Atmospheric Environment
• /
• 제7권3호
• /
• pp.152-160
• /
• 2013

Seven potentially harmful bifunctional carbonyls were measured in particulate and gaseous phases at a roadside site and a suburban site in an area about 30 km north-northwest from Tokyo metropolitan area in the Kanto region in Japan. For the first time, these compounds were measured in both phases with a time resolution of 2 h. We found that wind direction is an important parameter that affects the collection of these compounds near the source, and it can cover the effects of other important variables. Our results confirmed that motor vehicles and especially diesel fuelled vehicles are important sources of these compounds. Photochemical generation is also an important source of these compounds in the gaseous phase. Transportation from the urban area is also important, particularly in the aerosol phase.

• 한국분무공학회지
• /
• 제19권3호
• /
• pp.142-148
• /
• 2014

In this study, characteristics of gaseous pollutants and particulate matter were investigated on the condition of DPF regeneration and normal DPF condition. THC, CO, $CO_2$, NOx, and $CH_4$ were analyzed by MEXA-7200H and CVS-7100 respectively. Particulate Matter (PM) was measured by difference in weight of Membrane filter. Particle Number (PN) was measured by CPC analyzer. And Sulfate, Nitrate, Organic were measured by Aerosol Mass Spectrometer (AMS). As a result, gaseous pollutants and particulate matter were detected in higher concentration during DPF regeneration than normal DPF condition. And the PN increased by 94%, the fuel consumption was reduced by 29% on DPF generation process. Sulfate, Nitrate and Organic were undetectable level during normal DPF condition. But the highest concentration of Sulfate, Nitrate and Organic were measured as $100{\mu}g/m^3$, $20{\mu}g/m^3$ and $15{\mu}g/m^3$ respectively on DPF regeneration condition. VOCs concentrations (Benzene, Toluene, Ethylbenzene, Xylene) were analyzed by using PTR-MS. Benzene and Toluene emission have little or no change depending on DPF regeneration. But the Ethylbenzene and Xylene have comparatively low emissions on DPF regeneration.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.86-92
• /
• 2003

To analyze the characteristics of ozone formation, measurements of the concentrations of individual exhaust hydrocarbon species have been made under various engine operating parameters in a 2-liter 4-cylinder engine for natural gas and LPG. Tests were performed at constant engine speed, 1800 rpm for two compression ratios of 8.6 and 10.6, with various operating parameters, such as excess air ratio of 1.0~1.6, bmep of 250~800 na and spark timing of BTDC 10~$55^{\circ}$. It was found that the natural gas gave the less ozone formation than LPG in various operating conditions. This was accomplished by reducing the emissions of propylene($C_3H_6$), which has relatively high maximum incremental reactivity factor, and propane($C_3H_8$) that originally has large portion of LPG. In addition, the natural gas show lower values in the specific reactivity and brake specific reactivity. Higher compression ratio of the test engine showed higher non methane HC emissions. However, specific reactivity value decreased since fuel species of HC emissions increase. brake specific reactivity showed almost same values under high bmep, over 500kPa for both fuels. This means that the increase of non methane HC emissions and the decrease of specific reactivity with higher bmep affect each other simultaneously. With advanced spark timing, brake specific reactivity values of LPG were increased while those of natural gas showed almost constant values.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.193-200
• /
• 2007

Natural gas is one of the most promising alternatives to gasoline and diesel fuels because of its lower harmful emissions, including $CO_2$, and high thermal efficiency. In particular, natural gas is seen as an alternative fuel for heavy-duty Diesel Engines because of the lower resulting emissions of PM, $CO_2$ and $NO_x$. Almost all CNG vehicles use the PFI-type Engine. However, PFI-type CNG Engines have a lower brake horse power, because of reduced volumetric efficiency and lower burning speed. This is a result of gaseous charge and the time losses increase as compared with the DI-type. This study was conducted to investigate the effect of injection conditions (early injection mode, late injection mode) on the combustion phenomena and performances in the or CNG Engine. A DI Diesel Engine with the same specifications used in a previous study was modified to a DI CNG Engine, and injection pressure was constantly kept at 60bar by a two-stage pressure-reducing type regulator. In this study, excess air ratios were varied from 1.0 to the lean limit, at the load conditions 50% throttle open rate and 1700rpm. The combustion characteristics of the or CNG Engine - such as in-cylinder pressure, indicated thermal efficiency, cycle-by-cycle variation, combustion duration and emissions - were investigated. Through this method, it was possible to verify that the combustion duration, the lean limit and the emissions were improved by control of injection timing and the stratified mixture conditions. And combustion duration is affected by not only excess air ratio, injection timing and position of piston but gas flow condition.

• Korean Chemical Engineering Research
• /
• 제48권2호
• /
• pp.268-274
• /
• 2010

유해대기오염물질인 중금속의 배출은 그 위해성으로 인해 엄격한 법적 규제를 하는 등 지대한 관심이 기우려지고 있다. 무연탄을 사용하는 상용 화력발전시설로부터 배출되는 중금속의 농도 및 배출특성에 대한 연구를 실시하였다. 대상 발전시설은 순환 유동층 연소로, 싸이클론, 보일러, 전기집진기 설비로 구성되었고 가스상 수은을 포함한 주요 중금속의 농도를 측정하기 위해 분진과 가스상 시료를 전기집진기(ESP) 전단과 연돌에서 측정하였다. 총 먼지량(TPM), PM-10, PM-2.5와 같은 입자상 물질의 배출량은 ESP 전단에서 각각 23,274, 9,555, $7,790mg/Sm^3$로 매우 높았으며, 이는 예측했던 바와 같이 미분탄 화력발전소보다 높은 수치였다. 그러나 ESP에 의한 먼지의 제거효율이 높기 때문에 연돌에서의 총 먼지량은 $0.16mg/Sm^3$ 정도였다. 마찬가지로 중금속 배출량 또한 ESP에서 높은 제거효율을 보였다. 입도분포와 입경 범위 별 중금속 농축 정도에 대한 데이터를 살펴볼 때 일부 금속의 농도는 작은 입경 범위에서 더 농축된 것을 보여 입자의 크기와 상관관계를 지어 볼 수 있었다. 수은의 경우 다른 금속들과 다르게 높은 휘발성 때문에 대부분이 가스 상태로 배출되며 그로 인하여 수은의 제거효율은 68% 정도로 다른 중금속들에 대한 제거효율보다 낮았다. ESP를 지나면서 수은 화학종이 원소수은에서 산화수은으로 변하는 것이 확인되었으며, 그로 인하여 습식세정탑이 설비된 다른 석탄 화력발전소에서는 원소 수은이 지배적인 데 반해 본 시설의 경우 연돌에서 총 수은의 절반 정도만 원소수은이었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권3호
• /
• pp.360-368
• /
• 2010

A SCR catalytic filter system is used for reducing $NO_x$ and soot emissions simultaneously from diesel combustors. The amount of ammonia (as a reducing agent) must be controlled with the amount of $NO_x$ to obtain an optimal $NO_x$ conversion. Hence, gas mixing between ammonia and exhaust gases is vital to ensure that the SCR catalyst is optimally used. If ammonia mass distribution is not uniform, slip potential will occur in rich concentration areas. At lean areas, on the other hand, the catalyst is not fully active. The better mixing is indicated by the higher uniformity of ammonia mass distribution which is necessary to be considered in SCR catalytic filter system. The ammonia mass distributions are depended on the flow field of fluids. In this study, the velocity field of gaseous flow is investigated to characterize the transport of ammonia in SCR catalytic filter system. The influence of different injection placements on the ammonia mass distribution is also discussed. The results show that the ammonia mass distribution is more uniform for the injector directed radially perpendicular to the main flow of inlet at the gravitational direction than that at the side wall for both laminar (Re = 640) and turbulent flows (Re = 4255). It is also found that the mixing index decreases as increasing the heating temperature in the case of ammonia injected at the side wall.

• Journal of Animal Science and Technology
• /
• 제60권11호
• /
• pp.27.1-27.8
• /
• 2018

Background: Enteric methane ($CH_4$) accounts for about 70% of total $CH_4$ emissions from the ruminant animals. Researchers are exploring ways to mitigate enteric $CH_4$ emissions from ruminants. Recently, nano zinc oxide (nZnO) has shown potential in reducing $CH_4$ and hydrogen sulfide ($H_2S$) production from the liquid manure under anaerobic storage conditions. Four different levels of nZnO and two types of feed were mixed with rumen fluid to investigate the efficacy of nZnO in mitigating gaseous production. Methods: All experiments with four replicates were conducted in batches in 250 mL glass bottles paired with the ANKOM$^{RF}$ wireless gas production monitoring system. Gas production was monitored continuously for 72 h at a constant temperature of $39{\pm}1^{\circ}C$ in a water bath. Headspace gas samples were collected using gas-tight syringes from the Tedlar bags connected to the glass bottles and analyzed for greenhouse gases ($CH_4$ and carbon dioxide-$CO_2$) and $H_2S$ concentrations. $CH_4$ and $CO_2$ gas concentrations were analyzed using an SRI-8610 Gas Chromatograph and $H_2S$ concentrations were measured using a Jerome 631X meter. At the same time, substrate (i.e. mixed rumen fluid+ NP treatment+ feed composite) samples were collected from the glass bottles at the beginning and at the end of an experiment for bacterial counts, and volatile fatty acids (VFAs) analysis. Results: Compared to the control treatment the $H_2S$ and GHGs concentration reduction after 72 h of the tested nZnO levels varied between 4.89 to 53.65%. Additionally, 0.47 to 22.21% microbial population reduction was observed from the applied nZnO treatments. Application of nZnO at a rate of $1000{\mu}g\;g^{-1}$ have exhibited the highest amount of concentration reductions for all three gases and microbial population. Conclusion: Results suggest that both 500 and $1000{\mu}g\;g^{-1}$ nZnO application levels have the potential to reduce GHG and $H_2S$ concentrations.

• 청정기술
• /
• 제27권3호
• /
• pp.207-216
• /
• 2021

석탄화력발전소로부터 배출되는 질소산화물(NO + NO₂ = NO_x)은 NH₃를 환원제로 사용하여 선택적으로 환원시키는 SCR(selective catalytic reduction) 탈질촉매시스템에서 효과적으로 제거될 수 있다. 이 SCR 촉매공정에서 원소수은을 산화시켜 후속공정에서 제거하기 위하여 수많은 산화촉매들이 제안되었으나 MW급 석탄연소시설이나 상업운전 중인 석탄발전소 탈질시스템에서 원소수은 산화성능을 실증한 사례들은 매우 드물다. 실배가스에서 수행한 실증연구들을 심층적으로 조사·분석한 바는 기존 SCR 탈질촉매뿐 아니라 수은산화능을 향상시킨 신촉매의 원소수은 산화활성은 석탄연소, 실배가스 등의 특성에 따라 매우 복잡한 양상을 띤다는 점이다. 그럼에도 불구하고 석탄연소시설에 사용하는 원료탄, 탈질시스템과 실증조건이 원소수은 산화능에 가장 큰 영향을 미치는 핵심 요소이다. 특히, 원료탄에 함유된 할로겐 함량은 탈질촉매공정의 중요성을 넘어서는 것으로 보여진다. 석탄에 존재하는 대표적인 할로겐 성분은 Cl, Br과 F이고 이들 중에서 Cl이 지배적이며 다른 할로겐계처럼 염으로 존재하지만 석탄연소 과정에서 미량의 Cl₂와 함께 HCl로 전환된다. 이러한 HCl은 원소수은 산화에 있어서 강력한 산화제로 작용하지만 석탄마다 Cl 함량이 다르기 때문에 HCl 농도 또한 강하게 의존한다.