• 대한환경공학회지
• /
• 제35권12호
• /
• pp.967-972
• /
• 2013

질소산화물 저감에 큰 효과가 있는 MILD 연소는 고온의 배기가스가 연소로내에 유입되는 양에 따라 질소산화물 저감 특성이 많은 영향을 받는다. 본 연구에서는 동심원관 형태의 MILD 연소로에서 바깥 원통의 배기가스 통로에서부터 안쪽 원통의 연소통로 사이에 연결관을 설치하고 배기가스를 유입하기 위해 coanda 노즐을 사용하였다. 이러한 coanda 노즐의 기하학적 형상 변화에 따라 고압공기 유량, 배기가스 유입량 특성을 수치해석을 통해 살펴봄으로써 최적의 coanda 노즐 형상을 도출하는 것을 본 연구의 목적으로 하였다. 본 연구의 전산 해석의 결과는 conada 노즐의 노즐 통로 간격이 0.5 mm, 노즐 각도 $4^{\circ}$, 노즐 확관 길이 146 mm일 때 최적의 유입량비가 되었고 노즐 통로 수직 길이는 유입량비에 무관하였다.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.4027-4035
• /
• 1996

Accuracy of gas flow measurements using sonic nozzle and factors which influence on the discharge coefficients of sonic nozzle are investigated with high pressure gas flow standard measurement system. The gas flow measurement system comprises two compressors, storage tank, temperature control loop, sonic nozzle test section, weighing tank, gyroscopic scale and data acquisition system. The experiments are performed at various nozzle throat diameter and inlet pressure. Overall uncertainty of discharge coefficients is estimated to less than .+-.0.2% and most of experimental data fall into this range. Dependence of discharge coefficients on the Reynolds number is good agreement with those suggested in ISO document. The influence of swirl on the discharge coefficients becomes greater as the nozzle throat diameter is enlarged. The discharge coefficient of conical nozzle shows about 4.5% lower discharge coefficients than those of toroidal nozzle, but variation trend with Reynolds number is very similar each other and reproducibility of data is very good.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.622-624
• /
• 2002

This paper describes a method for steady state hot gas flow analysis considering nozzle ablation for the nozzle of $SF_6$ gas circuit breaker. In order to take account of the effect of ablated nozzle material on the hot gas flow. the PTFE mass concentration equation is added to the established equations for hot gas flow analysis. The steady state simulations were carried out under the condition of DC current flows and the results are presented.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.14-15
• /
• 2006

In this study, a new laval type nozzle was designed and manufactured. Using this nozzle tin powder was produced in close coupled system by using nitrogen gas at different operating conditions. The results showed that the increasing the gas pressure up to 1.47 MPa reduced the mean powder size down to 11.39 microns with a gas/melt mass flow rate ratio of 2.0. Powders are spherical in shape and have smooth surfaces.

• 자원리싸이클링
• /
• 제11권3호
• /
• pp.17-24
• /
• 2002

There has been an increasing demand over the years for steels with lower[s] content. For the purpose of improving the efficiency of desulphrization in the powder injection process of ladle, experimental studies were carried out by using cold model to optimize the lance configuration, gas flow rate, immersion depth of lance nozzle, position of lance nozzle relative to the ladle and the effect with slag, etc. As the results of this study, it was made clear that 2-hole nozzle lance (C, E type) placed in an asymmetric position gives the shortest mixing times.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권2호
• /
• pp.76-82
• /
• 2005

In this paper, a method for analyzing the thermal recovery characteristics of the nozzle of gas circuit breaker was described. In order to obtain thermal recovery characteristics, the transient simulation of SF6 arc plasma within the nozzle was carried out. In particular, the nozzle ablation was taken into account by simultaneously solving the PTFE concentration equation with the governing equations such as continuity, momentum and energy equation. After that, post arc current calculation was performed with the rate of rise of recovery voltage changed. From the calculated post arc current, it was possible to suggest the thermal recovery characteristics of the nozzle of gas circuit breaker.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.33-38
• /
• 2012

An experimental study was carried out to observe the characteristics of impingement of assist gas from a rectangular supersonic nozzle on kerf surface in laser machining. A micro-scale supersonic (Mach number 2.0) rectangular nozzle system was designed and fabricated for the purposes, and hot tests of the performance of the nozzle system was proceeded in the ITI corporation laboratory. For various related parameters such as laser powers, nozzle pressures and cutting speeds, the quality of the frontal view of cut edge surfaces was observed by a microscope. In the study, it was shown that the application of the present micro-rectangular supersonic nozzle in an off-axis configuration made it possible to cut a mild steel, by combinations of relatively low laser - powers, large standoff distances, and assist gas with no oxygen, which was not achieved by conventional laser cutting processes.

• 한국환경과학회지
• /
• 제27권8호
• /
• pp.621-629
• /
• 2018

Many chemically active species such as ${\cdot}H$, ${\cdot}OH$, $O_3$, $H_2O_2$, hydrated $e^-$, as well as ultraviolet rays, are produced by Dielectric Barrier Discharge (DBD) plasma in water and are widely use to remove non-biodegradable materials and deactivate microorganisms. As the plasma gas containing chemically active species that is generated from the plasma reaction has a short lifetime and low solubility in water, increasing the dissolution rate of this gas is an important challenge. To this end, the plasma gas and water within reactor were mixed using the air-automizing nozzle, and then, water-gas mixture was injected into water. The dissolving effect of plasma gas was indirectly confirmed by measuring the RNO (N-Dimethyl-4-nitrosoaniline, indicator of the formation of OH radical) solution. The plasma system consisted of an oxygen generator, a high-voltage power supply, a plasma generator and a liquid-gas mixing reactor. Experiments were conducted to examine the effects of location of air-automizing nozzle, flow rate of plasma gas, water circulation rate, and high-voltage on RNO degradation. The experimental results showed that the RNO removal efficiency of the air-automizing nozzle is 29.8% higher than the conventional diffuser. The nozzle position from water surface was not considered to be a major factor in the design and operation of the plasma reactor. The plasma gas flow rate and water circulation rate with the highest RNO removal rate were 3.5 L/min and 1.5 L/min, respectively. The ratio of the plasma gas flow rate to the water circulation rate for obtaining an RNO removal rate of over 95% was 1.67 ~ 4.00.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.167-173
• /
• 2003

For the measurement of mass flow rate at a wide range of operation conditions, it is required that the critical nozzle gas different diameters, since the mass flow rate through the critical nozzle depends on the nozzle supply conditions and the nozzle throat diameter. In the present study, both computational and experimental investigations are performed to explore the variable critical nozzle. Computational work using the 2-dimensional, axisymmetric, compressible Navier-Stokes equations are carried out to simulate the gas flow through variable critical nozzle. In experimnet, a cylinder with several different diameters is inserted into the critical nozzle to vary the nozzle throat diameter. Computational results are compared with the experimented ones. The computed results are in close agreement with experiment. It is found that the displacement and momentum thickness of variable critical nozzle are given as a function of Reynolds numbers. The discharge coefficient of the variable critical nozzle is predicted using an empirical equation.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1995년도 제2회 KOSCI Workshop
• /
• pp.105-121
• /
• 1995

The objective of this study is to find out the design data for gas burner with an axal and radial type nozzles. The design parameters are chosen as the stabilizer type, the jet hole size of gas nozzle, the distance between gas nozzle and stabilizer, the size of stabilizer and the hole size of stabilizer, the stabilizer type with or without air swirler, the angle of swirler. For the experimental test combustor sizing ${\phi}1.3m{\times}L4.5m$ is designed and manufactured, in which the set up of power diagram, the exhaust gas analysis, blow-off test, the flame temperature and the direct photography are performed.