• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.98-103
• /
• 2007

The number of vehicles employing diesel engines is rapidly rising. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced exhaust regulations. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter (PM), but the improvement of a regeneration performance at any engine operation point presents a considerable challenge by itself. Temperature, gas compostion and flow rate of exhaust gas are important parameters in DPF evaluation, especially regeneration process. Engine dynamometer and degment tester are generally used in DPF evaluation so far. But these test method couldn't reveal the effect of various parameters on real DPF, such as O2 concentration, amount of soot and exhaust gas temperature. This research has studied the possibility using dump combustor that used to take an approach lean premixed combustion in gas turbine for a DPF power and optimized. It is possible that utilize the system as DOC (Diesel Oxidation Catalyst) and SCR(Selective Catalytic Reduction) assessments test as well as DPF evaluation

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.97-102
• /
• 2003

Experimental investigations were carried out in an atmospheric pressure, optically accessible and laboratory-scale dump combustor operating on natural gas. The objective of this study is to obtain the phase-resolved gas temperatures at different phases of the oscillating pressure cycle during unstable combustion. CARS temperature measurements were made at several spatial locations under lean premixed conditions to get the information on temperature field within the combustor. Also the effect of incomplete fuel-air mixing on phase-resolved temperature fluctuation was investigated. Results including phase-resolved averaged temperature, normalized standard deviation and temperature probability distribution functions (PDFs) were provided in this paper. Temperature PDFs give an insight on the flame behavior. And strong correlation between phase-resolved temperature profile and pressure cycle was observed. Results of the phase-resolved high temperature give an additional information on the perturbation of equivalence ratio at flame as well as the effect of mixing quality on NOx emission characteristics.

• 한국연소학회지
• /
• 제23권1호
• /
• pp.13-20
• /
• 2018

Transverse acoustic mode in annular combustion chambers affects air-fuel mixing characteristics in the nozzle and can result in heat release fluctuations in the combustor. In addition, the acoustic mode coupling between the nozzle and the combustion chamber is one of the key parameters determining combustion instability phenomenon in the annular combustor. In this study, acoustic coupling between the nozzle and annular combustor was numerically analyzed using 3D-based in house FEM code. As a result, it was found that the acoustic mode inside the combustion chamber at anti-node locations of the transverse mode was strongly influenced by the nozzle inlet boundary conditions.

• 대한기계학회논문집B
• /
• 제34권4호
• /
• pp.443-448
• /
• 2010

가스발생기 사이클 액체로켓엔진에서 추진제의 공급압력 변화에 대한 성능 즉, 연소압, 터빈 파워, 엔진 혼합비, 가스발생기 연소가스의 온도 변화를 제시하였다. 로켓엔진의 주요 13개 시스템 레벨 변수를 이용하여 엔진 성능을 수치적으로 계산한다. 산화제 공급압이 증가하면 연소압과 터빈 파워는 증가하며 연료 공급압이 증가하면 연소압과 터빈 파워가 감소한다. 연료 유량 증가에 따라 감소된 가스 발생기의 혼합비는 연소가스 온도를 감소시키며 터빈 구동매질로서의 연소가스 물성을 저하시킨다. 연료 유량 증가에 따라 감소된 터빈 파워는 엔진 추력에 직접 영향을 미치는 주연소기의 연소압을 감소 시킨다.

• 한국추진공학회지
• /
• 제13권2호
• /
• pp.42-53
• /
• 2009

가스터빈 엔진을 모사하기 위한 프로그램을 2차원 CFD 코드를 기반으로 개발 하였다. 압축기와 터빈은 k-$\omega$ SST 난류 모델의 2차원 NS(Navier Stokes) 코드를 이용하였고, 연소기는 lumped method 화학 평형 코드를 바탕으로 완전 혼합 상태에서 연소효율 100%로 가정된 케로신 공기 반응의 생성물 중 대표적인 10종류를 몰분율을 계산, 당량비에 따른 연소기 온도를 예측하였다. 압축기, 터빈에서 로터의 회전에 의한 비정상 유동 현상은 mixing-plane 기법을 이용한 경계면 처리로 그 효과를 나타내었고, 압축기는 연소기로 온도 압력을 주고, 연소기는 터빈으로 온도와 질유량을 전달하나 압력의 변화가 없는 것으로 가정하였다. 이를 바탕으로 아음속 조건에서의 압축기 입구 조건과 터빈 출구 조건, 회전수, 연소기의 당량비를 주는 것만으로 엔진의 성능이 계산 될 수 있는 통합 코드를 구성하였다.

• 한국수소및신에너지학회논문집
• /
• 제31권4호
• /
• pp.351-362
• /
• 2020

Recently, renewable power is rapidly increasing globally due to extensive effort to mitigate climate change and conventional power generation industry faces new challenges. The gas turbine technology has potentials to expand its role in future power generation based on the intrinsic characteristics such as fuel diversity and fast load following ability. Hydrogen is one of the most promising fuel in terms of reducing emissions and storing variable renewable energy and replacing hydrocarbon fuel with hydrogen has become very popular. Therefore, this paper presents the core technologies to combust hydrogen added fuel efficiently in gas turbines and the analysis of domestic and international R&D trends.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.54-61
• /
• 2003

The first stage rotating blade of industrial gas turbine is one of the components that is normally run in exposed state at the highest temperature of the combustion gas stream. For this reason superior materials and advanced cooling technology are required to allow higher heat resisting characteristics of the component. The 1st stage blade of a selected commercial gas turbine blade made of directionally solidified Ni-based superalloy has a row of cooling holes on its trailing edge. In most cases, minor cracks have been found at some of the root cooling holes after one cycle operation (24,000 hrs) or even shorter operation time because of the high temperature gradient and the frequently alternating thermal stress. In the repair process, unfortunately, it is usually very difficult to get rid of the damage due to the fact that cracks are initiated at the root cooling hole and propagated deep into the hole. In this study, the feasibility of removing the sidewall cracks in the hole by utilizing EDM drilling has been investigated. Also the criteria of surface integrity for EDM drilling were established to achieve high quality repair as well as machining accuracy.

• 한국연소학회지
• /
• 제9권4호
• /
• pp.22-27
• /
• 2004

Lean premix combustion is a best method in low $NO_x$ gas turbine combustor and we must know the characteristics of NO emission in high temperature and pressure condition in premix flame. Numerical analysis was performed to investigate the NO emission characteristics by adopting a counterflow as a model problem using detailed chemical kinetics. Methane $(CH_4)$ was used as a test fuel which is the main fuel of natural gas. The tested parameters were stretch rate, equivalence ratio, initial temperature, and pressure in premix flame. Results showed that NO emission was high in low stretch rate, near stoichiometric equivalence ratio, high initial temperature, and high pressure. Also, the pressure effect was sensitive in high temperature condition.

• 항공우주기술
• /
• 제12권1호
• /
• pp.200-206
• /
• 2013

액체로켓엔진에서 추진제 밀도와 공급 압력 변화에 대한 성능 민감도를 분석하였다. 해석 프로그램은 터보펌프-가스발생기 연계시험 결과와 비교하여 1% 오차를 가지는 것으로 확인되었다. 연료 공급압력이 증가하면 혼합비 감소로 인해 엔진 연소압이 감소하였고 연료의 밀도가 증가하면 혼합비 감소에도 불구하고 추진제 유량이 증가하므로 엔진 연소압이 증가하는 것으로 예측되었다. 또한 산화제의 밀도가 증가되거나 공급압력이 증가하면 엔진의 연소압이 증가할 것으로 분석되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.155-160
• /
• 2001

The low NOx characteristics have been investigated to develop the combustor for micro turbine. The lean premixed combustion technology was applied to reduce the NOx emission. The test was conducted at the condition of high temperature and ambient pressure. The combustion air which has the temperature of $450\sim650K$ were supplied to the combustor through the air preheater. The temperature and emissions of NOx and CO were measured at the exit of combustor, The exit temperature and NOx were increased and CO was decreased with increasing inlet air temperature. The premixing chamber can be operated very lean condition of equivalence ratio around 0.35. The NOx was decreased with decreasing the equivalence ratio. The CO was decreased with decreasing the equivalence ratio, but the CO was increased with decreasing the equivalence ratio below 0.4. But, at the very lean condition of equivalence ratio below 0.35 both NOx and CO were increased because of the flame unstability. The NOx was decreased and CO was increased with increasing inlet air flowrate. This results can be used to determine the size of combustor. Consequently the performance of combustor shows the possibility of the application to the gas turbine system.