• International Journal of Korean Welding Society
• /
• 제3권1호
• /
• pp.29-33
• /
• 2003

The ferritic stainless steels are generally considered to have poor weldability compared with that of the austenitic stainless steels. However the primary advantages of ferritic stainless steels include lower material cost than the more commonly used austenitic stainless steels and a greater resistance to stress corrosion cracking. Thus, the weldability of ferritic stainless steels was investigated in this study. In concerning the weldability, Grain size measurement test, Erichsen test and Varestraint test were involved. full penetration welds were produced by autogeneous direct current straight polarity (DCSP) and pulsed currents gas tungsten arc welding (GIAW) and the effect of pulsed currents welding on the welds was compared to that of DCSP welding. The results showed that pulsed current was effective to refine grain size in the weld metal and the finest grain size was obtained at the frequency of 150Hz. In addition, the ductility of welds was lower than that of base metal. Finally, autogeneous type 444 welds were less susceptible to macro solidification cracks, but more sensitive to micro cracks; SEM/EDS analysis indicated that all the inclusions in the crack showed enrichment of Mn, Si, O and S.

• 한국지역사회생활과학회지
• /
• 제18권1호
• /
• pp.39-53
• /
• 2007

The purpose of this study was to determine the characteristics of an experimental protective clothing material with regard to comfort and isolation from the hazardous heavy metals produced in municipal waste incineration. An analysis was conducted on the total concentrations of heavy metals in some parts such as surface, middle layer, and interior for the treated fabric, and the untreated one, and working clothes. We conclude that the processed fabric with charcoal for working clothes showed the least exposure to heavy metals of the three. Working clothes worn by workers during waste incineration were much more contaminated than the untreated and treated materials. The material of working clothes could be chosen according to the function with regard to its original chemical characteristics, which are the proper results of the dyeing process. The processed fabric material has high degrees of moisture regain, thermal insulation, water vapor penetration, and antibacterial function; consequently, it is much more comfortable to wear. The fabric material proposed in this research contributed much more to blocking heavy metal concentrations (such as Cd, Pb, Cu, Cr, Zn, Mn) than did the fabric of working clothes at present. Consequently, we strongly suggest that the material of working clothes be upgraded by adopting the above-mentioned charcoal-processed fabric. Materials of working clothes must be improved to increase comfort and prevent harmful gas, flying dust, and heavy metals from permeating the fabrics.

• 제어로봇시스템학회논문지
• /
• 제11권12호
• /
• pp.1039-1044
• /
• 2005

This paper presents a robotic agent design and application in the ubiquitous intelligent space. We set up an experimental environment with Bluetooth host, Bluetooth client, furniture and home appliance, and robotic agents. First, the agents basically performed patrol guard to detect unexpected penetration, and to keep home safely from gas-leakage, electric leakage, and so on. They were out to patrol fur a robbery while navigating in a living room and a private room. In this task, we used an area-based action making and a hexagon-based Q-learning to control the agents. Second, the agents communicate with Bluetooth host device to access and control a home appliance. The Bluetooth host offers a manual control to person by inquiring a client robot when one would like to check some place especially. In this exercise, we organize asynchronous connection less (ACL) between the host and the client robots and control the robot maneuver by Bluetooth host controller interface (HCI).

• 한국주조공학회지
• /
• 제30권3호
• /
• pp.115-120
• /
• 2010

Recently, an advanced raw material supplying system in diecasting industry that molten metal produced by the raw material supplier can be directly delivered to the diecasting shops was proposed. It was known to have advantages of reducing melting process cost and improving working environment. However, for its successful mass production, the development of high insulation ladle is inevitable. In this study, the optimal mixing ratio of $SiO_2-Al_2O_3$ was investigated and the high insulation ladle with computer simulation result was built in a prototype and evaluated. The prototype which has refractory wall of $SiO_233%-Al_2O_3$ 35%-CaO 33% showed high insulation sufficient for carrying the Al molten metal for 138 minutes. Gas quantity result and SEM-EDS analysis on the melt poured in the ladle also showed extremely low level of 0.028 cc / 100 g and no penetration of Al molten metal into the refractory wall, satisfying the requirements for mass production.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.744-744
• /
• 2009

The development of safe and suitable hydrogen storage materials is one of key issues for commercializing hydrogen as an energy carrier. Carbon based materials have been investigated for many years to store hydrogen by the adsorption of the gas on the surface of the carbon structure. Recently, it is reported that carbon nitride nanobells have high hydrogen storage capacity since the nitrogen atom plays an important role on attracting hydrogen molecules. Here we report carbon nitride microporous spheres (CNMS) which have the maximum surface area of 995.3 $m^2/g$. Melamine-Formaldehyde resin is the source of carbon and nitrogen in CNMS. Most of the CNMS pores have diameters in the range of 6 to 8 A which could give a penetration energy barrier to a certain molecule. In addition, the maximum hydrogen storage capacities of carbon nitride spheres are 1.9 wt% under 77 K and 1 atm.

• Structural Engineering and Mechanics
• /
• 제68권1호
• /
• pp.95-101
• /
• 2018

The low rate of penetration and short lifetime of drilling bit served as the most common problems encountered in hard formation drilling, thus leading to severe restriction of drilling efficiency in oil and gas reservoir. This study developed a new local impact drilling method to enhance hard formation drilling efficiency. The limitation length formulas of radial/lateral cracks under static indentation and dynamic impact are derived based on the experimental research of Marshall D.B considering the mud column pressure and confining pressure. The local impact rock breaking simulation model is conducted to investigate its ROP raising effect. The results demonstrate that the length of radial/lateral cracks will increase as the decrease of mud pressure and confining pressure, and the local impact can result in a damage zone round the impact crater which helps the rock cutting, thus leading to the ROP increase. The numerical results also demonstrate the advantages of local impact method for raising ROP and the vibration reduction of bit in hard formation drilling. This study has shown that the local impact method can help raising the ROP and vibration reduction of bit, and it may be applied in drilling engineering.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.632-638
• /
• 2002

Electron beam (EB) and Gas tungsten arc (TIG) welds were performed on 12.7 mm thick Ti-6Al-4V plate (ASTM Titanium Grade 5). Charpy-V toughness and hardness, as well as, microstructure of the welds and penetration from the macrostructure were studied. It appears that by EB welding rather smaller $\beta$-grains than with TIG welding can be obtained. Next to the fusion line the $\beta$-grain size in the HAZ was 50 ${\mu}{\textrm}{m}$l while in the weld metal it was 150 ${\mu}{\textrm}{m}$. Charpy-V toughness of the EB weld metal was equal or even better to that of base metal, which shows that the $\alpha$-martensite per se is not particularly brittle if only the grain size is fine enough. This is similar to behavior of low carbon martensite in steel. The grain size was studied with light optical and scanning electron (SEM) microscopes. Thus for products, for products which can be manufactured automatically with very narrow fit, the EB welding of Ti-6Al-4V appears to yield satisfactory toughness without any complex post weld heat treatment. ill this study as in earlier studies the TIG welds gave lower toughness than that of the base material due to the higher heat input and slower cooling as compared to EB welding.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.253-255
• /
• 2006

Grey relational analysis has been carried out to develop a new approach for optimization of Nd:YAG laser and MIG hybrid welding parameters. The quality of welded material depends on welding parameters. The parameters chosen for current study include wire type, shielding gas, laser energy, laser focus, traveling speed, and wire feed rate. The welding experiments were performed on 6K21-T4 aluminum alloy sheet. Functional demands on products may vary widely depending on their use. The ultimate tensile stress, width, and penetration were chosen as the optimization criterion. Practice based on an orthogonal array which is following Taguchi's method has been progressed. Base on the results of grey relational analysis, the optimal process parameters were obtained. This integrated work was judged and it is observed that the results obtained by using the optimal parameters are much improved compared to those obtained through initial setting.

• Korean Chemical Engineering Research
• /
• 제46권2호
• /
• pp.397-401
• /
• 2008

레이저 애블레이션에 의해서 가지상 구조체 형상인 나노입자 응집체를 합성하였다. 기존 마이크론 금속섬유 필터의 표면상에 나노입자 응집체를 고착하여 여과성능을 향상시켰다. 에어로졸 상에서 소결 처리된 나노입자 응집체를 증착한 후 열처리를 하여 나노구조체가 표면상에 형성된 소결 처리된 나노입자 응집체 고착 필터를 제작하였다. 소결 온도가 증가할수록 마이크론 금속섬유 필터 표면상에 고착된 나노입자 응집체의 표면적 증가로 인하여 차압은 조금 증가하지만 여과효율은 현저하게 증가하였다.

• 대한기계학회논문집B
• /
• 제31권5호
• /
• pp.467-472
• /
• 2007

In this study the penetration distance of liquid phase fuel(i.e. liquid phsae length) was investigated in evaporative field. An exciplex fluorescence method was applied to the evaporative fuel spray to measure and investigate both the liquid and the vapor phase of the injected spray. For accurate investigation, images of the liquid and vapor phase regions were recorded using a 35mm still camera and CCD camera, respectively. Liquid fuel was injected from a single-hole nozzle (l/d=1.0mm/0.2mm) into a constant-volume chamber under high pressure and temperature in order to visualize the spray phenomena. Experimental results indicate that the liquid phase length decreased down to a certain constant value in accordance with increase in the ambient gas density and temperature. The constant value, about 40mm in this study the, is reached when the ambient density and temperature of the used fuel exceed critical condition.