• 한국식품저장유통학회지
• /
• 제7권2호
• /
• pp.218-221
• /
• 2000

The effect of the amounts of kimchi (100, 200 and 300 g) and fermentation temperature (10, 15 and 20$^{\circ}C$) on gas formation of kimchi during fermentation were investigated. The pH of the 200 g packaged kimchi for 12 days at 10-15$^{\circ}C$ was higher than 100 g and 300 g packaged kimchi, whereas that of 100 g packaged kimchi at 20$^{\circ}C$ was higher than the other products. Total lactic acid bacteria in was highest in the 200-300 g packaged kimchi fermented for 12 days at 10$^{\circ}C$. Number of Leuconostoc mesenteroides and Lactobacillus plantarum of 200 g packaged kimchi higher with the lower fermentation temperature, and that of Lactobacillus plantarum was higher in the kimchi fermented at 15$^{\circ}C$. The periods of gas formation was 8-11 days of fermentation at 10$^{\circ}C$, 1-7 day at 15$^{\circ}C$, and 5-6 days at 20$^{\circ}C$, respectively. The order of gas formation amount in the temperature and amount of kimchi was 15 > 20 > 10$^{\circ}C$ and 300 > 200 > 100 g, respectively.

• 생명과학회지
• /
• 제20권8호
• /
• pp.1159-1165
• /
• 2010

간접 열량측정법은 호흡 시의 산소 소모량이나 이산화탄소나 질소의 배출량을 측정해 에너지 소모량을 측정하고, 산화작용의 열 방출량(칼로리소비)을 산출하여 측정한다. 지난 20년 내에 간접 열량측정법에서 사용된 laboratory와 computerized 시스템은 현저하게 발전되었으며, 특히 매 호흡의 변인의 산출을 가능하게 해주는 호흡당 시스템의 사용이 증가되었다. 많은 이전의 연구에서 호흡당 시스템은 간접 열량측정도구로 타당도와 신뢰도가 높아 실험에 적합하다고 평가 하였다. 본 연구는 간접 열량측정법의 가장 적합한 호흡당 시스템을 분석하고자 한다. 하지만 다른 모든 호흡당 간접열량측정계의 타당도와 신뢰도의 효과를 검증한 연구가 많지 않다는 문제점이 있다. 그러므로, 앞으로 연구에서는 호흡당 간접열량측정계의 가장 타당도와 신뢰도가 높은 적합한 측정도구가 필요하다고 사료된다.

• 한국수소및신에너지학회논문집
• /
• 제16권2호
• /
• pp.136-141
• /
• 2005

Li-doped NiO was synthesized by molten salt method. $LiNO_3$-LiOH flux was used as a source for Li doping. $NiCl_2$ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5:1 to 30:1 during the synthetic procedure and the Li doping amount of synthesized materials were found between 0.086-0.190 as a Li ion to Ni ion ratio. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies, however the lattice parameter decreased from 0.41769nm in pure NiO to 0.41271nm as Li doping amount increased. Hydrogen gas sensors were fabricated using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs $H_2$ concentration was checked up to 4% of $H_2$ in air (as higher concentrations above 4.65% are explosive in air) using Li doped NiO of Li ion/Ni ion=0.111 as the sensor material. The response time T90 and the recovery time RT90 were less than 25 sec. There was minimum interference of other gases and hence $H_2$ gas can easily be detected.

• 공업화학
• /
• 제29권5호
• /
• pp.626-629
• /
• 2018

연료전지는 높은 연료유연성을 갖고 있어, 탄소 및 탄화수소 등을 통해서도 전기를 생산할 수 있다. 하지만 이러한 연료원을 사용한 경우, 불안정한 장기 구동성능이 종종 관측된다. 본 연구에서는 반응기 내부에 존재하는 탄화수소가 장기 구동성능을 불안정하게 함을 밝힌다. 본 연구진은 비활성기체인 아르곤을 이용하여 산화극 반응기 내부의 가스화경로를 예측하고, 이를 통해 탄화수소의 영향을 억제하여 불안정한 장기 구동성능을 극복한다. 더 나아가, 산화극 반응기 내부에 이산화탄소를 공급하여 역부드아반응을 유도한다. 역부드아반응을 통해 탄소연료전지에서 연료로 사용될 수 있는 일산화탄소를 만들어낸다. 과도한 이산화탄소의 주입은 오히려 연료손실 등의 문제를 야기함을 확인한다. 따라서, 본 연구에서는 이산화탄소 공급량의 최적화가 중요함을 밝히고, 이를 통해 연료전지 구동 성능을 안정화한다.

• 한국재료학회지
• /
• 제21권8호
• /
• pp.461-467
• /
• 2011

Cu(In, Ga)$Se_2$ (CIGS) precursor films were electrodeposited on Mo/glass substrates in acidic solutions containing $Cu^{2+}$, $In^{3+}$, $Ga^{3+}$, and $Se^{4+}$ ions at -0.6 V (SCE) and pH. 1.8. In order to induce recrystallization, the electrodeposited $Cu_{1.00}In_{0.81}Ga_{0.09}Se_{2.08}$ (25.0 at.% Cu + 20.2 at.% In + 2.2 at.% Ga + 52.0 at.% Se) precursor films were annealed under a high Se gas atmosphere for 15, 30, 45, and 60 min, respectively, at $500^{\circ}C$. The Se amount in the film increased from 52 at.% to 62 at.%, whereas the In amount in the film decreased from 20.8 at.% to 9.1 at.% as the annealing time increased from 0 (asdeposited state) to 60 min. These results were attributed to the Se introduced from the furnace atmosphere and reacted with the In present in the precursor films, resulting in the formation of the volatile $In_2Se$. CIGS precursor grains with a cauliflower shape grew as larger grains with the $CuSe_2$ and/or $Cu_{2-x}Se$ faceted phases as the annealing times increased. These faceted phases resulted in rough surface morphologies of the CIGS films. Furthermore, the CIGS layers were not dense because the empty spaces between the grains were not removed via annealing. Uniform thicknesses of the $MoSe_2$ layers occurred at the 45 and 60 min annealing time. This implies that there was a stable reaction between the Mo back electrode and the Se diffused through the CIGS film. The results obtained in the present research were sufficiently different from comparable studies where the recrystallization annealing was performed under an atmosphere of Ar gas only or a low Se gas pressure.

• 에너지공학
• /
• 제28권4호
• /
• pp.8-12
• /
• 2019

Thermal amine scrubbing is the most advanced CO₂ capture technique but its largescale application is hindered due to the large heat requirement during solvent regeneration step. The addition of a solid metal oxide catalysts can optimize the CO₂ desorption rate and thus minimize the energy consumption. Herein, we evaluate the solvent regeneration performance of Monoethanolamine (MEA) and Diethanolamine (DEA) solvents without and with two metal oxide catalysts (TiO₂ and V₂O₅) within a temperature range of 40-86℃. The solvent regeneration performance was evaluated in terms of CO₂ desorption rate and overall amount of CO₂ desorbed during the experiments. Both catalysts improved the solvent regeneration performance by desorbing greater amounts of CO₂ with higher CO₂ desorption rates at low temperature. Improvements of 86% and 50% in the CO₂ desorption rate were made by the catalysts for MEA and DEA solvents, respectively. The total amount of the desorbed CO₂ also improved by 17% and 13% from MEA and DEA solvents, respectively. The metal oxide catalyst-aided regeneration of amine solutions can be a new approach to minimize the heat requirement during solvent regeneration and thus can remove a primary shortfall of this technology.

• 센서학회지
• /
• 제27권1호
• /
• pp.47-54
• /
• 2018

In this paper, we describe the thermal characteristics of the output voltages of ethanol gas sensor according to the amount of radiation incident on the infrared sensors located at each focal point of two elliptical waveguides. In order to verify the output characteristics of the gas sensor according to the amount of incident light on the infrared sensor, two combinations of sensor modules were fabricated. Hydrophobic thin film is deposited on one of the reflectors of sensor modules and one of the two infrared sensors was equipped with a hollow disk (10 Ø), and the temperature characteristics of the infrared sensor equipped with the hollow disk (10 Ø) and the infrared sensor without the disk were tested. The temperature was varied from 253 K to 333 K at 10 K intervals based on 298 K. The properties of ethanol gas sensor have been identified with respect to varying temperature for a range of ethanol concentration from 0 ppm to 500 ppm. In the case of an infrared sensor equipped with a hollow disk (10 Ø), the output voltage of the sensor decreased by 0.8 mV and 1 mV, respectively, as the temperature increased. Conversely, the output voltage of the diskless infrared sensor showed an average increase of 67 mV and 57 mV as the temperature increased. The ethanol concentrations estimated on the basis of results show an error of more than 10 % for less than 100 ppm concentration. However, if the ethanol concentration exceeds 100 ppm, the gas concentration can be estimated within the range of ${\pm}10%$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.369-370
• /
• 2005

LTCC (Low Temperature Cofired Ceramic) technology is one of technologies which can realize SIP (System-In-a-Package). In this paper realization of gas sensor using LTCC technology was described. In the conventional gas sensor structure, wire bonding method is generally used as an interconnection method whereas in the LTCC sensor structure, via was used for the interconnection. As sensing materials, $SnO_2$ was adopted. The effect of frit glass portion on the adhesion of the sensing material to the LTCC substrate and the electrical conductivity of the sensing material were analyzed. AgPd, PdO, Pt was added to the sensing material as an additive for improving the gas sensitivity and electrical conductivity and the effect of the amount of additives in the sensing material on the electrical conductivity was investigated. The effect of the amount of frit glass in the termination on the sensor performance, especially mechanical integrity, was considered and the crack initiation and propagation in the boundary between the sensing material and the termination was studied.

• 대한건축학회논문집:구조계
• /
• 제36권4호
• /
• pp.143-152
• /
• 2020

This study analyzes in detail greenhouse gas emissions in building sector. To this end, this study used data on building characteristics (including building type, region, and construction year) and monthly energy consumptions (including electricity, city gas, and district heat) for all buildings from 2015 to 2018. These data were collected from the National Building Energy Database and the energy consumptions were converted into greenhouse gas (GHG) emissions. The total amount of GHG emissions from the building sector has increased steadily from 2015 (118.1MtCO2eq.) to 2018 (132.6MtCO2eq.). On the other hand, the more recently constructed buildings had lower GHG intensities. This result shows that strengthening building design criteria was effective on the reduction of GHG emissions in buildings, and that the increased buildings contributed to increasing GHG emissions of the building sector. In addition, sales facilities are thought to have the largest reduction potential as they had the highest amount of GHG emissions and GHG intensity. This study is expected to help establish new policies for GHG reduction in building sector as well as to evaluate the effects of existing policies.

• 자원리싸이클링
• /
• 제32권2호
• /
• pp.43-51
• /
• 2023

본 연구에서는 자동차엔진의 신품제조시와 재제조시 발생하는 환경영향을 전과정 관점에서 산정하고 이를 기반으로 온실가스 저감효과를 산정하였다. 자동차엔진 원부자재 원료취득 및 제조공정에서 배출되는 온실가스량은 신품제조시 약 3,473 kg, 재제조시 약 872 kg으로 재제조를 통해 저감되는 온실가스량은 약 2,601kg으로 나타나 폐기 단계를 제외한 전과정 측면에서 저감효과가 있는 것으로 분석되었다. LCA 가중화 분석 결과 신품 제조시 환경영향은 1.07E+03 Eco-point, 재제조시 2.67E+02 Eco-point로 나타났으며, 주요 6대 영향 범주 중 지구온난화 점유비율이 99.72%, 99.68%로 높게 나타났다.