• 대기
• /
• 제33권5호
• /
• pp.441-456
• /
• 2023

The mobile observation method, in which a meteorological drone observes while ascending, can observe the vertical profile of wind at 1 m-interval. In addition, since continuous flights are possible at time intervals of less than 30 minutes, high-resolution observation data can be obtained both spatially and temporally. In this study, we verify the accuracy of mobile observation data from meteorological drone (drone) and fill the spatio-temporal observation gaps in the lower atmosphere. To verify the accuracy of mobile observation data observed by drone, it was compared with rawinsonde observation data. The correlation coefficients between two equipment for a wind speed and direction were 0.89 and 0.91, and the root mean square errors were 0.7 m s^-1 and 20.93°. Therefore, it was judged that the drone was suitable for observing vertical profile of the wind using mobile observation method. In addition, we attempted to resolve the observation gaps in the lower atmosphere. First, the vertical observation gaps of the wind profiler between the ground and the 150 m altitude could be resolved by wind observation data using the drone. Secondly, the temporal observation gaps between 3-hour interval in the rawinsonde was resolved through a drone observation case conducted in Taean-gun, Chungcheongnam-do on October 13, 2022. In this case, the drone mobile observation data every 30-minute intervals could observe the low-level jet more detail than the rawinsonde observation data. These results show that the mobile observation data of the drone can be used to fill the spatio-temporal observation gaps in the lower atmosphere.

• 한국콘텐츠학회논문지
• /
• 제11권12호
• /
• pp.674-681
• /
• 2011

조선 시대 인쇄물인 삼강행실도는 세계 만화역사에서도 이른 시기인 1434년에 간행되었다. 삼강행실도에는 만화기호인 '만화칸'과 '칸과 칸 사이'가 등장한다. 만화기호인 만화칸의 상징성 못지않게 칸과 칸 사이도 만화기호에서 상징적 의미가 있다. 만화역사의 측면에서 보면 칸이 등장한 후, 칸과 칸 사이가 등장한 그 자체만으로도 의미를 부여할 수 있다. 그 상징적 근거들을 찾아 밝힘으로써 국내 만화역사의 역사적 근거가 다져질 것이다. 삼강행실도에서는 칸과 칸 사이의 형식적인 유형을 크게 두 가지로 나눌 수 있다. 첫 번째는 '구름칸과 구름칸 사이'이며, 두 번째는 '구름칸과 배경칸 사이'이다. 삼강행실도의 두 가지 유형인 칸과 칸 사이는 현대 만화와 비교할 때 모양이나 연출에서 차이를 보이지만 칸과 칸 사이의 의미는 유사하다고 하겠다. 이처럼 본 연구는 삼강행실도의 칸과 칸 사이의 형태를 분석함으로써 국내 만화역사의 타당한 근거를 제시하는 데 의미가 있다. 만화기호 중에서도 칸과 칸 사이에 초점을 맞추어, 삼강행실도의 칸과 칸 사이의 형태를 증명하는 것이 연구의 목적이다.

• 대한치과보철학회지
• /
• 제42권5호
• /
• pp.489-500
• /
• 2004

Statement of problem: The use of zirconia prostheses fabricated with CAD/CAM system is on an increasing trend in dentistry. However, evaluation of the fit related to internal relief and marginal reproducibility of zirconia has not been reported. Purpose : This study was to evaluate the fit related to internal relief and marginal reproducibility of zirconia core fabricated with CAD/CAM system. Materials and methods: The evaluation was based on 30 zirconia cores and 5 IPS-Empress2 cores. Zirconia cores were fabricated in different conditions of internal relief(0, 10, 20, 30, 40 and $50{\mu}m$), and IPS-Empress2 cores were fabricated in accordance with the manufacturer's instructions. Before cementation, the marginal discrepancies or cores were measured on metal die. And then, each core was cemented to stone die, embedded in an acrylic resin and sectioned in two planes(mesiodistally and labiopalatally). The internal gaps were measured at the margin and axial surface. Measurements for the marginal discrepancies, the internal marginal gaps and the internal axial gaps were performed under a measuring microscope(Compact measuring microscope STM5; Olympus, Japan) at a magnification of ${\times}100$. In addition, the marginal conagurations of metal die, zirconia core and IPS-Empress2 core were examined with SEM(S-2700, Hitachi, Japan). Results : Within the limits of this study the results were as follows. 1. Compared with IPS-Empress2 cores, the marginal discrepancies of zirconia cores had no significant differences. the internal marginal gaps were statistically smaller and the internal axial gaps were statistically larger in each condition of internal relief. 2. The marginal discrepancies and the internal marginal gaps of zirconia cores had no significant differences related to the conditions of internal relief(P>0.05). 3. The internal axial gaps of zirconia cores with $0{\sim}20{\mu}$m for internal relief were significantly larger than that with $50{\mu}m$ (P<(0.0001). 4. SEM micrographs showed favorable marginal reproducibility of zirconia core and smooth texture on the milling surface. Conclusion: The marginal discrepancy and the internal gaps of zirconia core were clinically acceptable and the milling surface was showed smooth texture. For fabrication of the durable esthetic restoration, further investigations on complex design of core, milling accuracy, compatability of enamel porcelain and porcelain firing seems to be needed.

• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.618-629
• /
• 1998

CAD/CAM-fabricated ceramic restorations nowadays are used as alternatives of amlagam and posterior composite resin restorations, especially in the cases of inlay restorations. But the reported results on marginal and internal fit of CAD/CAM-fabricated ceramic inlay have showed considerable difference. In this study, to evaluate the marginal and internal fit of CEREC2-fabricated ceramic inlay restoration and to compare with the fit of gold inlay and amalgam restoration, standardized Class II MO cavities were prepared in forty extracted caries-free human premolars. The teeth with prepared cavities were divided into 4 groups of ten teeth each. In group 1, CEREC2-fabricated ceramic inlays were treated with Scotchbond Multi-Purpose Plus(SMP plus) and cemented with Scotchbond Resin Cement. In group 2, casted gold inlays were cemented in the same method as in group 1. In group 3, casted gold inlays were cemented with zinc-phosphate cement. And in group 4, the prepared cavities were restored with amalgam. Restored teeth were thermocycled, stored in 1% methylene blue for 24 hours, and sectioned faciolingually and mesiodistally using EXAKT. Sectioned surfaces were observed with stereomicroscope and the gaps were measured at 9 points of mesiodistally sectioned surface and 7 points of faciolingually sectioned surface. The measured data were treated by Kruskal-Wallis one way ANOVA and Student-Newman-Keuls test. 1. The differences among measured gaps at each points were statistically significant for 4 experimental groups (P<0.05). 2. There were statistically significant differences in the measured gaps at each points between group 1 and group 2, group 1 and group 3, group 1 and group 4, group 2 and group 4, and group 3 and group 4 (P<0.05). 3. There were not statistically significant differences in the measured gaps at each points between group 2 and group 3 (P>0.05). 4. In the cases of inlay restorations(group 1, group 2, group 3), the gaps at internal line angle(distopulpal, axiogingival, faciopulpal, linguopulpal line angle) had a tendency to increase. In the cases of amalgam restorations(group 4), the gaps at occlusal margin, gingival margin and axiogingival line angle were greater than those at the other parts of cavities. 5. In CEREC2-fabricated ceramic inlays which were treated with Scotchbond Multi-Purpose Plus and cemented with Scotchbond Resin Cement, the mean gaps were $111{\mu}m$ at cavity margins, $168{\mu}m$ at vertical walls of cavities, $225{\mu}m$ at internal line angles and $123{\mu}m$ at cavity floors.

• 보존과학회지
• /
• 제35권5호
• /
• pp.494-507
• /
• 2019

A diagnostic investigation of the conservation state of damaged murals of the Payathonzu temple mainly indicated delamination, exfoliation, and contamination of the coloring layer; cracks and damage to the wall; and separation from gaps. In particular, vulnerabilities resulting from cracks in the wall and damage from gaps demand swift reinforcement measures. Ultrasonic testing uncovered damage caused by gaps between the base layer and plastered wall in several areas of the mural, vulnerable parts in the wall around the cracks, and considerable degradation of the physical properties where cracks and gaps were severe. Moisture measurements identified vast disparities in moisture depending on location even within a single area of the mural, and it was clear that these disparities were the result of environmental conditions such as humidity. Damage to the murals in monument 477 was the most severe, and a diagnostic of the physical properties uncovered severe physical damage to the upper part of the mural as well as to the corridor ceiling, thus presenting the need for conservation treatment utilizing scientific diagnosis as well as objective data.

• 대한기계학회논문집A
• /
• 제35권5호
• /
• pp.495-501
• /
• 2011

나노간극에서 발생하는 전기방전에 대해서 실험적으로 연구하고 그 결과를 분석하였다. Pt-Ir 합금으로 구성된 음극과 금으로 박막코팅된 양극사이에 전기방전을 하였다. 음극과 양극에서 전기장을 10V~80V 범위에서 제어하였으며, 간극은 50nm 에서 800nm 로 제어하였다. 이때 발생된 전기방전신호, 쇼트신호 등은 간접적으로 나노간극에서 발생하는 현상들을 이해할 수 있었다. 실험결과 전기방전은 전기장과 음극의 전극첨단의 반경에 매우 밀접하게 관련이 있었다. 작은 간극에서 발생하는 전기방전은 비교적 산포도가 크고 랜덤한 형태를 보였으며 음극 전극첨단의 반경에 민감하게 반응하였다.

• 대한간호학회지
• /
• 제34권2호
• /
• pp.225-234
• /
• 2004

Purpose: The purpose of this study was to develop a tool that measures the quality of nursing service, to measure the quality of nursing service perceived by consumers, and to identify the gaps between ideal and actual nursing services. Method: A questionnaire was developed and distributed to 300 people who had been hospitalized in one of six general hospitals with quality of nursing services in five provincial cities in Korea. For data analysis, the SPSS/WIN(ver 10.0) program was used. Result: The 20 attributes included in the instrument of quality of nursing service is abstracted into 2 factors: tangibility and intangibility. In quality analysis, 15 of 20 attributes are minus scores, meaning that those nursing services are perceived as generally low. However among the minus scores' attributes, only two attributes are significant statistically. Gaps between importance and performance of the nursing service exists in 19 among 20 attributes. Conclusion: Nursing service quality (performance-expectation) needs to be improved, and Gaps (importance-performance) reduced. In addition, a tool measuring nursing service quality has to be developed so nurses can deal successfully with the quality and gaps of nursing service perceived by consumers.

• Journal of Korean Neurosurgical Society
• /
• 제46권3호
• /
• pp.195-198
• /
• 2009

Objective : Medpor porous polyethylene was used to reconstruct small bone defects (gaps and burr holes) along a craniotomy bone flap. The feasibility and cosmetic results were evaluated. Methods : Medpor Craniotomy Gap Wedges, V and T, were designed. The V implant is a 10 cm-long wedge strip, the cross section of which is an isosceles triangle with a 4 mm-long base, making it suitable for gaps less than 4 mm after trimming. Meanwhile, the Medpor T wedge includes a 10 mm-wide thin plate on the top surface of the Medpor V Wedge, making it suitable for gaps wider than 4 mm and burr holes. Sixty-eight pterional craniotomies and 39 superciliary approaches were performed using the implants, and the operative results were evaluated with respect to the cosmetic results and pain or tenderness related to the cranial flap. Results : The small bone defects were eliminated with less than 10 minutes additional operative time. In a physical examination, there were no considerable cosmetic problems regarding to the cranial bone defects, such as a linear depression or dimple in the forehead, anterior temporal hollow, preauricular depression, and parietal burr hole defect. Plus, no patient suffered from any infectious complications. Conclusion : The Medpor Craniotomy Gap Wedge is technically easy to work with for reconstructing small bone defects, such as the bone gaps and burr holes created by a craniotomy, and produces excellent cosmetic results.

• 한국CDE학회논문집
• /
• 제22권1호
• /
• pp.59-69
• /
• 2017

Internal capacity of a refrigerator is an important indicator for design and purchasing criteria. The components facing the internal space may have holes or gaps between parts. In traditional way, design engineers manually remodeled the parts to fill the holes and the gaps for enclosed boundary of the internal space. Then they calculated internal volume by subtracting the assembly of parts from its enclosing volume. However, filling holes and gaps is not an automated process requiring a plenty of labor and time. In this research, we have developed a voxel-based method to estimate the internal volume of a refrigerator automatically. It starts transforming all components facing the interior space into voxels and fills all holes and gaps automatically by the developed hole-filling algorithm to form a completely closed boundary of the assembly. Then, it identifies the boundary voxels that are facing to the internal voxels with any part of the component. After getting the intersection points between the boundary voxels and the surfaces of components, it generates the boundary surface of triangular facets with the intersection points. Finally, it estimates the internal volume by adding volume of each tetrahedron composed of a triangle of boundary surface and an arbitrary point.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1326-1336
• /
• 2018

This paper proposes a numerical approach to predict the critical flashover voltages of air gaps under lightning impulses. For an air gap, the impulse voltage waveform features and electric field features are defined to characterize its energy storage status before the initiation of breakdown. These features are taken as the input parameters of the predictive model established by support vector machine (SVM). Given an applied voltage range, the golden section search method is used to compute the prediction results efficiently. This method was applied to predict the critical flashover voltages of rod-rod, rod-plane and sphere-plane gaps over a wide range of gap lengths and impulse voltage waveshapes. The predicted results coincide well with the experimental data, with the same trends and acceptable errors. The mean absolute percentage errors of 6 groups of test samples are within 4.6%, which demonstrates the validity and accuracy of the predictive model. This method provides an effectual way to obtain the critical flashover voltage and might be helpful to estimate the safe clearances of air gaps for insulation design.