• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of Korea Foundry Society
• /
• v.25 no.1
• /
• pp.23-29
• /
• 2005

Mechanical characteristics of Hi-Cr cast irons containing 16.8%Cr and 3.0%C were studied with various heat treatments. After as-cast Y-block ingots were annealed fully, the ingots were machined into cylinderical specimens with the size of 9mm in diameter and 20mm in length in order to investigate the effect of heat-treatments on mechanical characteristics of high Cr cast irons. All specimens were heat-treated by quenching- tempering, austempering and cyclic heat at the various temperatures(950, 1000, 1050 and $1100^{\circ}C$) respectively. The wear amount was measured for each heat-treated specimens against the counterpart of a hardened SKD11 steel at the following conditions; wearing velocity: 0.7 m/s, load: 100N and sliding distance: 70 km. After as-cast specimens were annealed, fine $M_{3}C$ carbides were formed, which affected the hardness and the wear resistance of Hi-Cr specimens. High hardness and good wear resistance were appeared on the specimens treated at 950 and $1000^{\circ}C$ and the austempered specimens show excellent wear resistance as well as high hardness.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.4
• /
• pp.310-319
• /
• 2019

Although mud shrimp (Upogebia Major) provides benefits on the tidal flat ecosystem, it is causing the mass mortality of Manila clam (Tapes philippinarum) and large economic loss to the aquaculture farmer due to spreading in the entire coastal clam farm area of the West Sea of Korea. In this study, a mud shrimp blocking box for cultivating clam was tested to prevent the mud shrimp from invading the habitat of the clam. To determine the effect of the blocking box, the growth characteristics of the clams under various culture conditions were investigated. The shell length, total weight, condition index, the presence of mud shrimp in the box, and the soil decay in the box were examined according to whether the clams were raised in the box or in natural state, whether the box is covered with a net or not and the gap size of the box. As a result, no significant differences in shell length, total weight, and condition index were found between the clam grown in the box and the natural state (P>0.05) without any evidence of invading of mud shrimp to the box. In addition, the soil inside the box was in good condition, not decayed. Therefore, using the mud shrimp blocking box, mud shrimp can be prevented from propagating to the habitat of the clam, thereby contributing to the normal production of the clam and thus to restoring the clam farming.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.16 no.4
• /
• pp.260-266
• /
• 1996

To find out the residual effect of phosphate fertilization level on the dry matter yield and nutrient plloductivity of pasture plants, this experiment was arranged as a randomized complete block design with six treatments(0-0, 50-50, 100-65, 150-65, 200-65 and 250-65kg $P_2O_5$), those were composed of three $P_2O_5$ fertilization level(0,50 and 65kg $P_2O_5$ after phosphate fertilization trial with six treatments(0, 50, 100, 150, 200 and 250kg $P_2O_5$/ha) from 1989 to 1992, and conducted at hilly land in Kwangju, Kyonggi Province from 1993 to 1994. The results obtained are summarized as follows : As the available phosphate of soil increase, the early growth and cover degree of pasture plants wintered were more favorable. With 150-65kg $P_2O_5$ application for two years, the average dry matter yield of grasses, 9,862kglha was similared to that of 200-65kg $P_2O_5$/ha. The crude protein and energy productivity of pasture plants tended to increase as available phosphate of soil was increased, but those were not different between 150-65 and 250-65kg P 2 0 4 a Efficiency of $P_2O_5$ was highest at $P_2O_5$ 150-65kg/ha fertilization, wHich produced dry matter 11 1.8kg. net energy lactation(NEL) 67 1.2M.f per I kg P205. Therefore, phosphate fertilization is recommended strongly application with 150kg/ha for three years after pasture establishment, and then 65kg/ha for two years a reasonabl management in hilly grassland.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2008.11a
• /
• pp.897-900
• /
• 2008

As the further development of economic globalization and the continued opening up of international construction markets, many of the countries are faced with more and more severe domestic and international construction market competition. It has been a focus question of all the countries and regions that how to achieve maximal profit in the international construction market, but construction claims are growing into a stumbling block to the project participants to reach their expected goals. Thus, the management of construction claims is considered as the greatest challenge that is facing constructors in today's vacillating business environment. Recently, many of the methodologies have been developed for the construction claims to overcome these current problems, but compared to the developed countries there is still a big gap in some Asian countries, such as China and Korea. This paper attempted to investigate and compare the project claims system in these two countries to figure out the common points and differences.

• Journal of the Korean Institute of Rural Architecture
• /
• v.22 no.2
• /
• pp.1-8
• /
• 2020

This study is intended to derive the adaptive reuse techniques through the history and aspects of new construction, extension, repair, and other works, limited to the deep and narrow lots facing Seongan-gil and Nammun-gil in Nammun-ro 2 ga of Cheongju, the historic urban area. The results are as follows. 1) In the case of newly built reinforced concrete buildings, the central part of the top floor of the residence or all floors are opened to the open space(void) to facilitate lighting and ventilation. This is developed as a convection phenomenon due to the temperature difference from the slits between buildings, which affects the entire air flow of the block. 2) The buildings of extension and repair are composed of two-story masonry or steel frame, both the front store facing the road and the house on the back, but it looks like one because it is in contact with each other. If only a small gap between the front and rear buildings is restored to an external space or a space equipped with sun light, a small breath can be provided in lighting and ventilation. 3) The existing two-story wooden stores and houses have lost their external space due to repairs. With minimal intervention to restore the small courtyard, slits, and space under the eaves, it will not only improve lighting and ventilation, but also create a unique appearance as a segment of the elongated store.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.90-97
• /
• 2010

The high efficiency power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device and DTMOS Error Amplifier is presented in this paper. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS(DT-CMOS) with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuits consist of a saw-tooth generator, a band-gap reference circuit, an DT-CMOS error amplifier and a comparator circuit as a block. the proposed DT-CMOS Error Amplifier has 72dB DC gain and 83.5deg phase margin. also Error Amplifier that use DTMOS more than CMOS showed power consumption decrease of about 30%. DC-DC converter, based on Voltage-mode PWM control circuits and low on-resistance switching device is achieved the high efficiency near 96% at 100mA output current. And DC-DC converter is designed with Low Drop Out regulator(LDO regulator) in stand-by mode which fewer than 1mA for high efficiency.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.48-53
• /
• 2012

The purpose of this paper studies the failure cases including with system of liquefied phase injection in liquified petroleum gas vehicle. The first case, resulting with inspection the injector of LPG, it occasionally certified the injection damage phenomenon that the fuel efficiency(km/l) was decreased to 5% by carbon deposit with injector hole when the driver operates the vehicle. The second case, it certified the interference phenomenon of air flow with carbon deposit in ISA system control for idle speed of engine and throttle body suppling air into engine. As a result, the fuel efficiency was decreased 7%. The third case, the outer air during intake stroke was intermittently flowed in this gasket gap because of weaken adhesion power phenomenon for cylinder block by intake manifold gasket tearing. Consequentially, it certified the decrease for fuel efficiency to 3% by risen the amount of fuel injection as the air inflow quantity. These failure examples reduced the power performance of engine and the fuel efficiency of vehicle. It have to minimize of failure phenomenon preparing through quality management.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.485-491
• /
• 2014

An Antenna & RF system for a fly-away satcom terminal application on ka-band is presented in this paper. The Fly-away satellite terminal can be moved and operated by two person and adapt automatic satellite tracking system in order to decrease the tracking time. Additionally, for low-power consumption, compact size and light-weight, a dual reflector antenna is constructed using dual-offset gregorian antenna structure. For minimize weight, the reflector of the antenna is made of Magnesium. For low-power consumption and light-weight, the pHEMT MMIC compound devices is utilized. The Electronic Band-Gap(EBG) Low-Pass Filter(LPF) is designed for harmonic rejection. In the receiving part, Low-Noise Block converter(LNB) structure is designed for compact and lightweight. In this paper, fly-away satcom terminal with low-power consumption, compact size and light-weight is described with antenna system and RF system performances. Through the experimentation, fly-away terminal's EIRP is more than 50dBW, G/T is more than $17dB/^{\circ}K$.

• The KIPS Transactions:PartB
• /
• v.15B no.1
• /
• pp.9-16
• /
• 2008

In this paper, we present an algorithm for synthesizing intermediate view image from a stereoscopic pair of images. An image of multiview is need for people in order to easily recognize 3D image. However, if many cameras are use for that, not only does system get more complicated but also transmission rating cause a big trouble. Hence, stereo images are photograph and issue on the sending side and algorithm to generate several intermediate view image is able to be use on the receiving side. The proposed method is based on disparity space image. First of all, disparity space image that is depicted by the gap of pixel followed by disparity of stereo image is generated. Disparity map is made by utilizing disparity space image for searching for optimal disparity path then eventual intermediate view image is generated after occlusion region which does not match is processed. Experimental results illustrate the performance of the proposed technique and we obtained a high quality image of more than 30 dB PSNR.