• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2021.06a
• /
• pp.131-134
• /
• 2021

지상파 방송에서는 청각장애인을 위해 폐쇄자막(closed caption) 서비스가 제공되고 있지만, 이를 저장하여 VOD 서비스 등에 제공하고자 할 때는 영상과의 비동기화(desynchronization) 문제로 인해 활용할 수 없는 문제가 있다. 본 논문에서는 이를 해결하기 위해 자동 음성인식(automatic speech recognition)과, 자막 동기화 문제에 맞게 변경된 동적계획법(modified dynamic programming)을 이용하는 방법을 제안한다. 문자열 정렬에서 삽입과 삭제 등 간격(gap)의 발생을 제어하는 제약조건과 그에 따른 점수 구조를 적용함으로써 문자열 정렬 성능을 개선한다. 또한 정렬된 폐쇄자막과 음성인식 문자열로부터 시간 동기정보를 복원하고 동기화된 자막을 생성하는 방법을 제안한다. 실제 TV 프로그램과 자막에 적용하여 기존 방법에 비해 성능의 향상이 있음을 확인하였다.

• Journal of the Korean Society of Visualization
• /
• v.21 no.2
• /
• pp.8-13
• /
• 2023

The primary challenge in improving fuel efficiency and reducing air pollution for commercial vehicles is reducing their aerodynamic drag. Various flow control devices, such as cab-roof fairing, gap fairing, cab extender, and side skirt have been introduced to reduce drag, however, the drag reduction effect and applicability are different depending on each commercial vehicle model. To evaluate the fuel consumption of heavy vehicles, a comprehensive research approach, including drag force measurement, flow field analysis is required. This study investigated the effect of a cab extender, which installed rear region of cab, on a drag coefficient of commercial vehicle through wind tunnel experiments and CFD. The results showed that the cab extender significantly modified the flow structure around the vehicle, leading to 8.2% reduction in drag coefficient compared to the original vehicle model. These results would provide practical application for enhancing the aerodynamic performance and fuel efficiency of heavy vehicle.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.205-209
• /
• 2016

The flowfield characteristics of a square prism having a small triangular prism at the upstream side were investigated by visualizing the flow field using PIV. The ratio of the width of the triangular prism to that of the square prism and the gap ratios between the square and triangular prisms were selected as the experimental parameters. The results are summarized as follows. The Strouhal number measured on the wake side of the square prism, which had the same characteristics as the drag reduction rate, increased, and then decreased with the gap ratio for the same width ratio. For a square prism having a small triangular prism, the stagnation regions were represented at the upstream and downstream sides of the square prism. The size of the stagnation region increased with the width ratio at the upstream side of the square prism, and decreased at the downstream side.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1433_1434
• /
• 2009

AC PDP는 다른 디스플레이들에 비해 높은 소비전력과 낮은 발광효율에 대한 문제를 가지고 있다. 이러한 문제를 해결하기 위해 본 연구에서는 기존의 Stripe shape ITO(Indium Tin Oxide)전극구조에서 Lock shape ITO전극구조를 제안하였다. 이 구조는 long gap을 가진 Square형태의 전극구조에 'ㄱ'형태의 점화전극을 추가한 구조로, 소비전력을 줄이기 위해 전극면적을 줄이고, discharge current를 제어 하였다. 또한 점화전극 구조에 의해 늘어난 gap으로 인한 방전개시전압 상승을 줄 일수 있었다. 실험은 Stripe shape ITO구조와 Lock shape ITO의 전극구조들로 구성되어 있는 Test Panel을 직접 제작하여 방전개시전압, 휘도, 소비전력, 발광효율을 측정하여 그 특성들을 비교하였다. 그 결과 제안된 전극구조에서의 소비전력은 reference 구조에 비해 최대 18% 감소하였고, 발광효율은 최대 13% 상승을 함을 보였다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.2
• /
• pp.75-82
• /
• 1999

A compensation method of the motor parameters using zero sequence third harmonic voltage is presented for the speed sensorless vector control of the induction motor considering saturation of the flux. Generally, the air-gap flux of the saturated induction motor contains the space harmonic components rotating with the synchronous frequency of the motor. Because the EMF of the saturated induction motor contains the zero sequence harmonic voltages at the neutral point of the motor, those harmonic voltages can be used as a saturation index. In this work, the rotor flux observer is firstly designed for the speed sensorless vector control of induction motor. And a novel measurement method of the space harmonic voltage and a compensation method of th LPF(Low Pass Filter) are proposed. For compensating the non-linear variations of the magnetizing inductance depending on the saturation level of the motor, the dominant third harmonic voltage of the motor is used as a saturation function of the air-gap flux. And the variation of the stator resistance owing to the motor temperature can also be measured with the phase angle between the impressed voltage vector and the zero sequence voltage. The validity of the proposed parameter compensation scheme in the speed sensorless vector control using rotor flux observer is verified by the result of the simulations and the experiments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.548-553
• /
• 2004

In this paper, single, two, and three-section microstrip directional couplers are implemented for realizing the high directivity characteristics. The achievement of the high directivity with microstrip configuration is carried out by the distributed capacitor to decrease the even and odd mode phase difference. Capacitive compensation is performed by gap coupling of open stub formed in sub-coupled line. Therefore, insertion loss and power handling capability are not affected by the gap coupling. The proposed structure is easy to fabricate and incorporate another microwave device due to the planner microstrip. We designed and fabricated single, two, and three-section directional coupler with 20 ㏈ coupling. In spite of microstrip structure, the capacitive compensation structure shows 30 ㏈, 27 ㏈, and 25 ㏈ of directivity in single, two, and three-section directional couplers, respectively.

• Journal of Powder Materials
• /
• v.28 no.3
• /
• pp.259-266
• /
• 2021

The (Ga_1-xZn_x)(N_1-xO_x) solid solution is attracting extensive attention for photocatalytic water splitting and wastewater treatment owing to its narrow and controllable band gap. To optimize the photocatalytic performance of the solid solution, the key points are to decrease its band gap and recombination rate. In this study, (Ga_1-xZn_x)(N_1-xO_x) nanofibers with various Zn fractions are prepared by electrospinning followed by calcination and nitridation. The effect of the composition and crystallinity of electrospun oxide nanofibers on the morphology and optical properties of the obtained solid-solution nanofibers are systematically investigated. The results show that the final shape of the (Ga_1-xZn_x) (N_1-xO_x) material is greatly affected by the crystallinity of the oxide nanofibers before nitridation. The photocatalytic properties of (Ga_1-xZn_x)(N_1-xO_x) with different Ga:Zn atomic ratios are investigated by studying the degradation of rhodamine B under visible light irradiation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.3
• /
• pp.292-296
• /
• 2024

In this study, Iron (III) oxide-hydroxide (δ-FeOOH) was successfully synthesized using hydrogen peroxide (H₂O₂) as an oxidizing agent. The synthesis of δ-FeOOH was carried out by controlling the amount of H₂O₂, and pure δ-FeOOH was successfully synthesized in ranges from 0.2 mL to 0.6 mL of H₂O₂. The size of the synthesized δ-FeOOH particles was compared by controlling the amount of oxidant H₂O₂. The average particle size of the synthesized pure δ-FeOOH particles increased from 875.1 nm to 897.2 nm as the amount of H₂O₂ was increased. The optical properties of δ-FeOOH synthesized under these specific conditions were investigated. All δ-FeOOH showed a similar trend of increasing and decreasing light absorption from 800 nm to 400 nm, although there was a slight difference in the amount of light absorption, with the largest amount of light absorption at 410 nm. The band gap energy of δ-FeOOH through the Tauc plot method was about 2.1~2.2 eV when H₂O₂ was 0.2~1.4mL. With a sufficient small particle size, simple control of that particle size, and a small band gap energy enough to absorb light in the visible spectrum, δ-FeOOH could be useful in a variety of applications, including photoelectrochemistry and battery electrodes.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.513-525
• /
• 2018

A 3 dimensional numerical analysis for shield TBM tunnel should take into account various characteristics of the shield TBM excavation, such as gap, tail void, segment installation, and backfill injection. However, analysis method considering excavation characteristics are generally mixed with various method, resulting in concern of consistency and reliability degradation of the analytical results. In this paper, a parametric study is carried out by using actually measured ground settlement data on various methods that can be used for 3 dimensional numerical analysis of shield TBM tunneling. As a result, we have analyzed and arranged an analytical method to predict similarly the behavior of ground settlement and tunnel face pressure at the design stage. Skin plate pressure, backfill pressure and soil model have been identified as the most significant influences on the ground settlement. The grout pressure model is considered to be applicable when there is no volume loss information on the excavated ground, such as seabed tunnels, or when it is important to identify the behavior around a tunnel, such as surface settlement as well as face pressure. And it is considered that designers can use these guidelines as a base material to perform a reasonable 3 dimensional numerical analysis that reflects the ground conditions and the features of the shield TBM tunneling.

• 전자공학회논문지 IE
• /
• v.47 no.4
• /
• pp.18-27
• /
• 2010

This paper is designed the efficient Data Acquisition System for an vibration of rotatory machines. The Data Acquisition System is consist of the analog logic having signal filer and amplifier, and digital logic with ADC, DSP, FPGA and FIFO memory. The vibration signal of rotatory machines acquired from sensors is controlled by the FPGA device through the analog logic and is saved to FIFO memory being converted analog to digital signal. The digital signal process is performed by the DSP using the vibration data in FIFO memory. The vibration factor of the rotatory machinery analysis and diagnosis is defined the RMS, Peak to Peak, average, GAP, FFT of vibration data and digital filtering by DSP, and is need to follow as being happened the event of vibration and make an application to an warning system. It takes time to process the several analysis step of all vibration data and the event follow, also special event. It should be continuously performed the data acquisition and the process, however during processing the input signal the DSP can not be performed to the acquisited data after then, also it will be lose the data at several channel. Therefore it is that the system uses efficiently the DSP and FPGA devices for reducing the data lose, it design to process a part of the signal data to FPGA from DSP in order to minimize the process time, and a process to parallel process system, as a result of design system it propose to method of faster process and more efficient data acquisition system by using DSP and FPGA than signal DSP system.