• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.7
• /
• pp.362-370
• /
• 2002

This paper describes the practical tuning method of dual-input PSS and its application to Muju P/P #2 with Proto PSS, which is based on DSP technology and uses both frequency and power. First, the model parameters of generator system used in this paper have been derived from the generator characteristic testing. Then, in the selection of PSS parameters, the Bode plot is plotted in order to tune the PSS's time constants which are able to compensate the phase lagging due to generator and excitation system. In addition, the eigenvalue analysis is also performed for determining a reliable PSS gain, $K_{s}$. Finally, the transient stability program has been utilized to verify the safe operation of Proto PSS against the predictable disturbances such as the AVR-step test and generator unloading test. In on-site test, the simulated results have been identically duplicated by implementing AVR step test in Muju P/P #2 with Proto PSS, which has the previously designed PSS parameters.s.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.3
• /
• pp.231-234
• /
• 2008

For the applications which need a micro-power supply such as thin and flat displays, micro-robot, and micro-system, it is especially necessary to integrate the passive components because they typically need more than 2/3 of the space of the conventional circuit. Therefore, we have designed and fabricated a novel piezoelectric micro transformer using the PZT thin film and MEMS technologies for application to the energy supply device of the micro-systems. The dimensions of the micro-transformer is $1000{\mu}m\;{\times}\;400{\mu}m\;{\times}\;4.8{\mu}m$ $(length{\times}width{\times}thickness)$. The dynamic displacement of around $9.2{\pm}0.064{\mu}m$ was observed at 10 V. The dynamic displacement varied almost linearly with applied voltage. The average voltage gain (step-up ratio) was approximately 2.13 at the resonant frequency $(F_r=8.006KHz)$ and load resistance $(R_L)$ of 1 $M{\Omega}$.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.83-89
• /
• 2008

This paper presents the dynamic analysis and input shaping control of a positioning stage. Vibration characteristics of the positioning stage are affected not only by the structural dynamics but also by the servo actuators that consist of the mechanism; driving motor and controller. This paper proposes an integrated dynamic model to accommodate both the structural dynamics and the servo actuators. Theoretical modal analysis with a commercial finite element code is carried out to investigate the dynamic characteristics of the experimental positioning stage. Experiments are performed to validate the theoretical modal analysis and estimate the equivalent stiffness due to the servo actuators. This paper deals with an input shaping scheme to suppress vibration of the positioning stage. Input shapers are systematically implemented for the positioning stage in consideration of its dynamics. The effects of servo control gain are also investigated. The experiments show that input shaping effectively removes residual vibrations and then improves the performance of positioning stage.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.6
• /
• pp.555-562
• /
• 1997

With only the classical PID controller applied to control of a DC motor, good (target) performance characteristic of the controller can be obtained if all the model parameters of DC motor and operating conditions such as external load torque, disturbance, etc. are known exactly. However, in case when some of system parameters or operating conditions are uncertain or unknown, the fixed PID controller does not guarantee good performance, which is assumed with precisely known system parameters and operating conditions. In view of this and the robustness enhancement of DC motor control system, we propose a PID learning controller which consists of a set of learning rules for PID gain tuning and learning of an auxiliary input. The proposed PID learning controller is shown to drive the state of uncertain DC motor system with unknown system parameters and external load torque to the desired one world wide asymptotically. Computer simulation and experimental results are given to demonstrate the effectiveness of the proposed PID learning controller, thereby showing its superiority to the conventional fixed PID controller.

• Journal of Oral Medicine and Pain
• /
• v.40 no.1
• /
• pp.3-9
• /
• 2015

The etiopathogenesis of burning mouth syndrome (BMS) seems to be complex and many patients probably involves interactions among local, systemic, and/or psychological factors in the pathophysiologic mechanism. Although there are controversies over whether the psychological factor is a cause or a result of BMS, several studies have supported strong relationships between psychological factors and chronic pain. It has been suggested that somatic complaints from unfavorable life experiences may influence both individual personality and mood changes; however, initiation of BMS symptoms is not necessarily correlated with stressful life events despite their elevated psychological stress. If the psychological distress is not a causal factor of BMS, it seems that BMS patients may be particularly vulnerable to psychological problems, primarily depression, anxiety, and hostility due to the characteristic entities of BMS such as chronic persistent pain itself. It seems likely that both physiological and psychological factors play a role in causing, perpetuating and/or exacerbating BMS; therefore, both two components of the patient's symptoms must be addressed. The acceptance of psychological factors by the patient is often an important element of BMS, management. The evaluation of psychological and emotional status of BMS patient enables clinicians to recognize prolonged negative and subclinical factors which can complicate the management of pain or indirectly perpetuate other physical factors. This evaluation improves the doctor-patient relationships, motivation, and compliance through a correct understanding of the clinical problem. Appropriate emotional and psychological evaluation may be required prior to developing a treatment plan in order to gain the successful treatment outcome.

• Journal of electromagnetic engineering and science
• /
• v.14 no.3
• /
• pp.299-305
• /
• 2014

A wideband circularly polarized (CP) antenna with a single feed is proposed for use in global navigation satellite systems. Its primary radiation elements are composed of two orthogonal bowtie dipoles, which are equipped with double-printed vacant-quarter rings to allow direct matching of the antenna to a single $50-{\Omega}$ coaxial line and to produce CP radiation. The crossed bowtie dipole is appropriately incorporated with a planar metallic reflector to produce the desired unidirectional radiation pattern as well as to achieve a wideband characteristic in terms of impedance matching and axial ratio (AR) bandwidths. The designed antenna was fabricated and measured. The prototype antenna with an overall 1.2-GHz frequency size of $0.48{\lambda}_o{\times}0.48{\lambda}_o{\times}0.25{\lambda}_o$ produced a measured ${\mid}S_{11}{\mid}$<-10 dB bandwidth of 1.05-1.79 GHz and a measured 3-dB AR bandwidth of 1.12-1.64 GHz. It also showed right-hand CP radiation with a small gain variation (${\pm}0.3dB$) and high radiation efficiency (>93%) over the operational bandwidth.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1908-1916
• /
• 2018

This paper proposes a controller design method for suppressing the resonance generated in the slave motor in the middle and low speed operation range, according to the load and parameter differences between two motors, during parallel operation using the master and slave method that controls two surface permanent magnet synchronous motors connected in parallel by a single inverter. The proposed resonance suppression controller is directly obtained by analyzing the resonance characteristics, using the lead controller method. Therefore, it is possible to fundamentally reduce trial and error to set the controller gain. In addition, because the proposed resonance suppression controller was designed as a lead controller, the stability region of the system increased owing to the added zero point, making the system robust with respect to parametric variations. Simulations and experiments confirmed the usefulness of the proposed method and the system's robustness with respect to parametric variations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1620-1627
• /
• 2001

In this paper, a broadband microstrip antenna for PCS and IMT-2000 service is designed. To obtain the broadband characteristics of an antenna, we utilized the multi-layered structure composed of two foam material layers, parasitic element and aperture coupled feeding network. The broadband characteristic is obtained by changing the size of parasitic element and the height of foam materials. In addition to that, the usage of metal layer at the distance of λ/4 from feed-line, back radiation is reduced. The bandwidth of a single element for VSWR less than 1.3 is about 550MHz. The bandwidth of a designed 1$\times$4 array antenna for VSWR less than 1.3 is about 460MHz. The gain of a designed array antenna is about 11.15∼12.15dBi and the front-to-back ratio is about 30dB.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.3
• /
• pp.173-180
• /
• 2001

In the past few years, the nondestructive inspection technology has greatly developed due to the increased necessity to gain a complete understanding of the bridge behavior. Especially, the deformations of bridges contain a lot of informations about its health state. By measuring these deformations it is possible to analyze the loading and aging behavior of the structure. However, the current, methods (such as LVDT, dial gage, optical displacement transducer, etc) are often of changeable application on site and have the limitations of installation. In this paper, the classical beam theory was reviewed and the deflections of structure are estimated using measured strain which is easy to acquire. The applicability of this algorithm is verified by laboratory(simple reinforced concrete beam) and field test. By this test, we proposed correction factor to estimate deflection of reinforced concrete beam after cracking, and analyze about the generation of correction factor. Also fiber optic sensors as well as resistive strain gages were installed in the concrete beams to establish the applicability of fiber optic sensors in the field of civil engineering.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.2
• /
• pp.183-190
• /
• 2007

In this paper, a robust controller for PWM converter is proposed. The proposde converter controller consists of a PI controller for DC output voltage and a current controller using error-space approach for maintaining the sinusoidal current waveform and unity power factor. Conventionally, the try and error method has been used to design the current controller considering the switching frequency of the devices and sampling frequency of the digital controller. But this proposed method is based on characteristic ratio assignment(CRA) method which has the advantage to design the optimal gain to meet the referenced response and overshoot within the limit range. First, the CRA based current controller algorithm is explained. Then the validity of proposed controller is verified through the PSiM simulation and experience results.