• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.3
• /
• pp.175-181
• /
• 2018

The use of dual-frequency measurements from the Global Navigation Satellite System (GNSS) enables us to observe precise ionospheric total electron content (TEC). Currently, many GNSS reference stations in South Korea provide both GPS and GLONASS data. In the present study, we estimated the grid-based TEC values and relative receiver differential code biases (DCB) from a GNSS network operated by the Korea Astronomy and Space Science Institute. In addition, we compared the diurnal variations in a TEC time series from solutions of the GPS only, the GLONASS only, and combined GPS/GLONASS processing. A significant difference between the GPS only TEC and combined GPS/GLONASS TEC at a specific grid point over South Korea appeared near the solar terminator. It is noted that GLONASS measurements can contribute to observing a variation in ionospheric TEC over high latitude regions.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.194-194
• /
• 2000

In aviation navigation by GPS, requirements on availability and integrity must be absolutely satisfied for safety. Current study on accomplishing this integrity includes RAM(Receiver Autonomous Integrity Monitoring), checking integrity internally in GPS receiver itself. However RAIM techniques have be investigated and presented under assumption that there is included only one fault in measurements from GPS, In case of multiple fault, an interaction among bias errors sometimes results in decreasing the effect of multiple fault. This may make an exact fault detection and identification difficult, and study on mutiple fault RAIM focused on. This paper explains the reasons that techniques applied on single fault are not adequate to extend directly to two faults case and shows that RAIM solution on two fault may be given in revised parity space.

• Journal of Internet Computing and Services
• /
• v.12 no.2
• /
• pp.29-36
• /
• 2011

In this paper, NMEA based Parser programming for Smart-phone was designed at a GPS receiver. The design scheme for Map API and sensor web services was designed according to the Google Map API standards that the position values of NMEA sentences were changed due to XML files. As a result of interfaces between GPS NMEA sentences of Smart-phone and Google Map API, it is possible that real time visual positioning sensor web services about the Google Map mapping from a GPS receiver could be worked on web sever.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.3
• /
• pp.344-350
• /
• 2006

The software GPS receivers based on the SDR technology provide the ability to easily adapt the other signal processing algorithms without changing or modifying the hardware of the GPS receiver. However, it is difficult to implement the software GPS receivers using a commercial processor because of the heavy computational burden for processing the GPS signals in real-time. This paper proposes an efficient GPS signal processing scheme to reduce the computational burden for processing the GPS signals in the software GPS receiver, which uses a fundamental notion compressing the replica signals and the encoded look-up table method to generate correlation values between GPS signals and replica signals. In this paper, it is explained that the computational burden of the proposed scheme is much smaller than that of the typical GPS signal processing scheme. Finally, the processing time of the proposed scheme is compared with that of the typical scheme, and the improvement in the aspect of the computational burden is also shown.

• Journal of Satellite, Information and Communications
• /
• v.11 no.4
• /
• pp.15-20
• /
• 2016

In this paper, we developed the hardware GPS signal generator for generating a GPS L1 meaconing signal with Live GPS signal signals and analyzed the performance of meaconing signal generator thorough the experiment. Deception of the signal, such as a re-broadcast, it is an object of the user to provide false information so as not to receive location information and accurate time. The signal just rebroadcast has the features that can be easily deceive the receiver via a delay of no received signal to the signal processing through an antenna. In this paper, the hardware for generating a signal only these rebroadcast designed and manufactured, by re-sending the received Live GPS signals, to confirm the effect of the receiver. The maximum delay time is possible up to about 2.6msec, also, has been successfully tested to be moved to the position of re-broadcasting based on maturity antenna the position of the receiver through a spaced antenna.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.278-285
• /
• 2009

Navigation system is applied in variety of fields including the simple location positioning, autopilot navigation of unmanned robot tractor, autonomous guidance systems for agricultural vehicles, construction of large field works that require high precision and map making process. Particularly utilization of GPS (Global Positioning System) is very common in the present navigation system. This study introduces a navigation system for autonomous field robot that travels to the pre-input path using GPS information. Performance of the GPS- based navigation is highly depended on its receiving rate because GPS receivers do not acquire any navigation information in the period between the refresh intervals. So this study presents an algorithm that improves an accuracy of the navigation by estimation the positional information during the blind period of a low rate GPS receiver. In fact the algorithm calculated the robot's heading in a 50 Hz rate, so the blind period of an 1 Hz GPS receiver is extensively covered. Consequently implementation of the algorithm to the GPS based navigation showed an improvement in guidance accuracy. The conventional field robot directly carried an expensive control computer and sensors onboard, therefore the miniaturization and weight reduction of the robot was limited. In this paper, the field robot carried only communication equipments such as GPS module, normal RC receiver, and bluetooth modem. This enabled the field robot to be built in an economic cost and miniature size.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.8
• /
• pp.774-787
• /
• 2011

This paper deals with quantitative analysis about the characteristics of GNSS(Global Navigation Satellite System) signals contaminated with multipath signals and day-to-day repeatability of the navigation solution and SNR(Signal to Noise Ratio) caused by multipath signals using the collected data from GPS receiver installed on KSLV-I which was on standby on the launch pad at Naro Space Center. Since the GPS antennas, surrounding environments and GPS satellite orbits were very slightly changed with respect to the day, the repeating pattern of the solution and SNR caused by the multipath signals was verified from the collected data. Analytic result of the multipath effects and day-to-day repeatability of the navigation solution and SNR observed at the launch pad would be used for obtaining more stable performance of the GPS receiver when the satellite launch vehicles are on standby.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.451-456
• /
• 2016

Because GPS signals are weak, system jamming is a real and present danger. This can happen when the receiver is subjected to intentional or unintentional interference by a transmitter. If the jamming signal is strong enough, the receiver can be operated to take corrective action automatically. Current methods to protect GPS receiver from jamming condition are based on spatial filtering. In this paper, the beamforming as referred to in signal processing technique used in arrays for directional signal reception was suggested and analyzed for anti-jamming. In order to change the directionality of the array when receiving a jamming signal, a beamformer can control the signal at each sensor. Therefore, cutoff angle ${\theta}$ was measured in the opposite direction of the jammer. GPS signals are only processed when the antenna element is within inside the cutoff angle. As a result, GPS positioning can be used in condition under cutoff angle $30^{\circ}$.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.141-144
• /
• 2006

The deviations in the injection orbital parameters, resulting from launcher dispersions, need to be estimated and used for autonomous satellite operations. For the proposed small satellite mission of the university there will be two GPS receivers onboard the satellite to provide the instantaneous orbital state to the onboard data handling system. In order to meet the power requirements, the satellite will be sun-tracking whenever there is no imaging operation. For imaging activities, the satellite will be maneuvered to nadir-pointing mode. Due to such different modes of orientation the geometry for the GPS receivers will not be favorable at all times and there will be instances of poor geometry resulting in no output from the GPS receivers. Onboard the satellite, the orbital information should be continuously available for autonomous switching on/off of various subsystems. The paper presents the strategies to make use of small arcs of data from GPS receivers to compute the mean orbital parameters and use the updated orbital parameters to calculate the position and velocity whenever the same is not available from GPS receiver. Thus the navigation message from the GPS receiver, namely the position vector in Earth-Centered-Earth-Fixed (ECEF) frame, is used as measurements. As for estimation, two techniques - (1) batch least squares method, and (2) Kalman Filter method are used for orbit estimation (in real time). The performance of the onboard orbit estimation has been assessed based on hardware based multi-channel GPS Signal simulator. The results indicate good converge even with short arcs of data as the GPS navigation data are generally very accurate and the data rate is also fast (typically 1Hz).

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.3
• /
• pp.137-144
• /
• 2016

In this paper, the performance of ranging measurement, which is generated using two receiver clock offsets in one receiver, was analyzed. A spoofer transmits a counterfeited spoofing signal which is similar to the GPS signal with hostile purposes, so the same tracking technique can be applied to the spoofing signal. The multi-correlator can generate two receiver clock offsets in one receiver. The difference between these two clock offsets consists of the path length from the spoofer to the receiver and the delay of spoofer system. Thus, in this paper, the ranging measurement was evaluated by the spoofer localization performance based on the time-of-arrival (TOA) technique. The results of simulation and real-world experiments show that the position and the system clock offset of the spoofer could be estimated successfully.