• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.63-64
• /
• 2014

In this study, we has a purpose to estimate the joint movement responsiveness performance for the domestic products of one-component structural silicon sealants. For this purpose, we make a comparative study for the four domestic products focused on tensile properties after allowed the cyclic-movements for three days at initial step of curing phase. A joint movement range ±10% and the rate of compression and extension 3.2mm/h were assumed in those tests. As a result, the large space were induced inside the sealant by rupture, and then adhesion and cohesion failures were caused by stress concentration. The tensile properties were reduced by 15~60% in comparison with physical properties. In this case, the generating defect was caused and the service-life was decreased. Thus, further researches as relationship of test condition and products properties on this behavior would be studied.

• Computers and Concrete
• /
• v.15 no.1
• /
• pp.73-88
• /
• 2015

Following previous studies, the current paper describes the results of an experimental program concerning the repair of reinforced concrete columns by thixotropic pseudo plastic mortar, preformed to analyze and quantify the influence of initial construction damage to the behavior of the repaired element. Five columns (section scale 1:2) were designed according to the minimum requirements of reinforcement of ductility orientated codes' design with variables the percentages of initial construction damages. All were tested in axial compression with repeated cycles up to failure. For comparison reasons, another one of the same characteristics, yet healthy, was constructed and tested as a reference specimen. A numerical study (Finite Element Analysis) was conducted for further investigation of the behavior of the thixotropic mortar as repair material. The results indicate that: a) surpassing a specific amount of damage, columns even suitably repaired present lower strain capacity, b) finite element analysis present the same way of deboning of the repaired material taking into consideration the buckling of the reinforcement bars.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.9
• /
• pp.37-43
• /
• 2016

This paper introduces a method for video shot group detection needed for efficient management and summary of video. The proposed method detects shots based on low-level visual properties and performs temporal and spatial clustering based on visual similarity of neighboring shots. Shot groups created from temporal clustering are further clustered into small groups with respect to visual similarity. A set of representative shot frames are selected from each cluster of the smaller groups representing a scene. Shots excluded from temporal clustering are also clustered into groups from which representative shot frames are selected. A number of video clips are collected and applied to the method for accuracy of shot group detection. We achieved 91% of accuracy of the method for shot group detection. The number of representative shot frames is reduced to 1/3 of the total shot frames. The experiment also shows the inverse relationship between accuracy and compression rate.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.4
• /
• pp.969-973
• /
• 2016

Interruption tests were conducted using the same circuit breaker for an initial pressure of SF₆ 0.5 MPa (gauge pressure) and CO₂ mixture 1.0 MPa, 0.8 MPa, and 0.6 MPa. The pressure-rises in the compression and thermal expansion chambers were measured for verifying the computational results using a simplified synthetic test facility. Further, the possibility of the CO₂ mixture substituting SF₆ gas was confirmed. Moreover, in view of the thermal recovery capability, it has also been confirmed that the pressure of the CO₂ mixture can be reduced almost to the same value as that of the SF₆ gas by optimizing the design parameters of the interrupter.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.41-46
• /
• 2005

For both economic and ecological reasons corrugated box manufacturers are seeking to produce acceptably strong boxes while using more recycled paper. This study was to develop hydrophilic coating agents in order to improve overall physical properties of recycled corrugated fiberboard liners. Two coating agents were developed and applied to 'S' corrugating medium. The results showed that compression strength of new liners, named 'S-A' and 'S-B', were increased significantly both standard humidity and high humidity environment and it was as much as 'SK' liner. New developed liners were also economically advantageous since new liners were estimated about one hundred fifty dollars per ton cheaper than SK liner. The study indicated that further work is needed on the coating technology and machine development.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2013.05a
• /
• pp.215-218
• /
• 2013

In this paper, we proposed a method for enhancement of color images with sky regions. The input image is converted into HSV space and then sky and non-sky regions are separated. For sky region, saturation enhancement is performed for each pixel based on the enhancement factor calculated from the average saturation of its local neighborhood. On the other hand, for the non-sky region, the enhancement is applied only on the luminance value (V) component of the HSV color image, which is performed in two steps. The luminance enhancement, which is also called as dynamic range compression, is carried out using nonlinear transfer function. Again, each pixel is further enhanced for the adjustment of the image contrast depending upon the center pixel and its neighborhood pixel values. At last, the original H and V component image and enhanced S component image for the sky region, and original H and S component image and enhanced V component image for the non-sky region are converted back to RGB image.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.71-76
• /
• 2020

In this paper, we propose a super-resolution method that reconstructs compressed low-resolution images into high-resolution images. We propose a CNN model with a small number of parameters, and even if quantization is applied to the proposed model, super-resolution can be implemented without deteriorating the image quality. To further improve the quality of the compressed low-resolution image, a new degradation model was proposed instead of the existing bicubic degradation model. The proposed degradation model is used only in the training process and can be applied by changing only the parameter values to the original CNN model. In the super-resolution image applying the proposed degradation model, visual artifacts caused by image compression were effectively removed. As a result, our proposed method generates higher PSNR values at compressed images and shows better visual quality, compared to conventional CNN-based SR methods.

• Communications of the Korean Mathematical Society
• /
• v.38 no.2
• /
• pp.431-450
• /
• 2023

The basic goal of quantization for probability distribution is to reduce the number of values, which is typically uncountable, describing a probability distribution to some finite set and thus to make an approximation of a continuous probability distribution by a discrete distribution. It has broad application in signal processing and data compression. In this paper, first we define the uniform distributions on different curves such as a line segment, a circle, and the boundary of an equilateral triangle. Then, we give the exact formulas to determine the optimal sets of n-means and the nth quantization errors for different values of n with respect to the uniform distributions defined on the curves. In each case, we further calculate the quantization dimension and show that it is equal to the dimension of the object; and the quantization coefficient exists as a finite positive number. This supports the well-known result of Bucklew and Wise [2], which says that for a Borel probability measure P with non-vanishing absolutely continuous part the quantization coefficient exists as a finite positive number.

• Steel and Composite Structures
• /
• v.45 no.1
• /
• pp.147-157
• /
• 2022

This study assessed the compressive and tensile strengths and modulus of elasticity of waste polyethylene terephthalate (PET) using the ASTM standard tests. In addition, short carbon and glass fibers were mixed with waste PET to examine the improvements in ductility and strength during compression. The bonding was examined via field-emission scanning electron microscopy. The strength degradation of the waste PET tested under UV was 40-50%. However, it had a compressive strength of 32.37 MPa (equivalent to that of concrete), tensile strength of 31.83 MPa (approximately ten times that of concrete), and a unit weight of 12-13 kN/m3 (approximately half that of concrete). A finite element analysis showed that, compared with concrete, a waste PET pile foundation can support approximately 1.3 times greater loads. Mixing reinforcing fibers with waste PET further mitigated this, thereby extending ductility. Waste PET holds excellent potential for use in foundation piles, especially while mitigating brittleness using short reinforcing fibers and avoiding UV degradation.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.301-306
• /
• 2011

The paper presents an analysis of the heating cycle and discusses a desalination cycle that uses lowtemperature seawater. The basic heating cycle model is the heat pump cycle, and seawater desalination is usually performed by the indirect freezing desalination method. The low temperature of the seawater (below $5^{\circ}C$) acts as the heat source of the evaporator. R-134a, R-1234yf, R-600a are used as working fluids. In the 2-stage compression cycle, the compressor's work decreased by about 15.6% from that in the 1-stage compression cycle. Further, the COP in the 2-stage cycle was 17.6% higher than that in the 1-stage cycle. In the indirect desalination cycle, the energy per unit fresh water productivity in the 2-stage cycle was 19.8% lower than that in the 1-stage cycle.