• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.279-286
• /
• 2002

For surface modification of polymers with hydrophilic functional groups, acrylic acid was grafted and immobilized on the surface of polyethylene(PE) by cold-plasma treatment using Ar gas. The modifications were identified by analysis of ATR-IR spectrum and by the measurement of contact angles. Compared to virgin PE significant decreases in contact angle were observed for both the grafted PE and the immobilized PE. The decreases of contact angle were in the range of 47~$53^{\circ}$ for grafted PE and 23~$26^{\circ}$ for immobilized PE. The degree of hydrophilicity depended strongly on the plasma-treating time and discharge power. For the case of grafting it has show that the longer plasma-treating time, the higher hydrophilic character. For the case of immobilization, whereas, higher discharge power and longer exposure to plasma have shown the detrimental effect for the preparation of hydrophilic PE surface due to the decrease of carboxyl group by ablation effect. The decrease in adhesion strength of immobilized PE. compared to grafted PE, was also attributed to the ablation of carboxyl group.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.49-55
• /
• 2001

The bi-functional ion exchangers, SAPP-g-(AN/St) were synthesized with mixed vinyl monomers(acrylonitrile and styrene) onto PP fabric by the pre-irradiation grafting with E-beam and its subsequent amidoximination and sulfonation. The degree of grafting of PP-g-(AN/St) was increased with decreasing acrylonitrile composition in the mixed monomers. The water uptake of copolymers increased with decreasing in the amidoxime ratio in the copolymers and increased by sulfonation, but decreased by amidoximation. The $UO_2^{2+}$ adsorption capacity of SPP-g-St, APP-g-AN, and SAPP-g-(AN/St) were 12.4, 34.0, and 38.0 mg/g, respectively and the optimum adsorption time is about 50 hrs. As a result of uranium adsorption, the synthesized ion exchanger, which we obtained have also good affinity toward the adsorption or chelating with $UO_2^{2+}$ ions.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.869-876
• /
• 2000

In order to improve the cell-compatability of poly(L-lactide-co-glycolide) (75 : 25 by mole ratio of lactide to glycolide, PLGA) surfaces, the physicochemical treatments have been demonstrated. Chemical treatments were 70% perchloric acid. 50% sulfuric acid and 0.5 N sodium hydroxide solution and physical methods were corona and plasma treatment. The water contact angle of surface treated PLGA decreased from 73$^{\circ}$ to 50~60$^{\circ}$, i.e., increased hydrophilicity, due to the introduction of oxygen-containing functional group onto PLGA backbone by the measurement of an electron spectroscopy for chemical analysis. It could be observed that the adhesion and growth of fibroblast cell on physicochemically treated PLGA surfaces, especially perchloric acid treated PLGA surface, were more active than on the controt. In conclusion, it seems that surface wettability as hydrophilicity of PLGA plays an important role in cell adhesion, spreading and growth.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.889-894
• /
• 1999

Preparation of micron size polymer particles which have desired morphology, size, and structure by emulsion polymerization is very difficult due to coagulation of latex particles and formation of second generation particles. But there are attractive merits such as preparation of structural and functional polymer particles in seeded emulsion polymerization. Seeded emulsion polymerization of n-butyl acrylate(BA) was carried out to investigate the effects of stirring rate, reaction temperature, concentration of initiator, emulsifier, and cross-linking agent on the particle size and size distribution. By the combination of suitable reaction conditions, we succeeded in preparing $0.14{\sim}3.67{\mu}m$ diameter of poly(n-butyl acrylate)(PBA) particles using sequential seeded emulsion polymerization.

• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.587-593
• /
• 2001

In this work, red mud (RM) was chemically modified by 0.1, 1, and 5 M H3PO4 solution to prepare epoxy/RM nanocomposites. The effect of chemical treatment on pH, acid-base values, specific surface area, and porosity of RM surface was analyzed. To estimate the mechanical interfacial properties of epoxy/RM nanocomposites, the critical stress intensity factor (K$_{IC}$) was measured. From the experimental results, it was clearly revealed that the porosity, specific surface area, and acid values of RM surface were developed as the increase of the treatment concentration due to the increase of acidic functional group, including hydroxyl group on RM surface. The mechanical interfacial properties of epoxy/treated-RM nanocomposites were higher than those of epoxy/RM as-received due to an improvement of interfacial bonding between basic matrix and RM surface.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.599-605
• /
• 2012

The physicochemical properties such as surface hardness, solvent mechanical wear resistance, and resistance to scratch properties of poly(3,4-ethylenedioxythiophene) (PEDOT) thin film prepared by vapor phase polymerization (VPP) was effectively improved by post-treatment of various metal alkoxide sol solutions. Metal oxide layer derived from sol-gel process of metal alkoxide was generated on the PEDOT thin film layer by VPP, resulting in improving mechanical properties of the conductive thin films without any deterioration of their original surface resistance. Several kinds of silicone and titanium alkoxide derivatives with various functional groups were used as metal alkoxide sol sources. Among them, PEDOT-metal oxide composite thin film derived tetraethyl orthosilicate showed the best performance in the terms of surface resistance, transmittance, and various physicochemical properties. The effect of metal alkoxide content in washing solution, oxidant content and drying temperature have been investigated in order to optimize the various properties of PEDOT-metal oxide composite thin film.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.219-224
• /
• 2015

In this work, the effect of fiber array direction including $0^{\circ}$, $0^{\circ}/90^{\circ}$, $0^{\circ}/45^{\circ}/-45^{\circ}$ was investigated for mechanical properties of basalt fiber-reinforced composites. Mechanical properties of the composites were studied using interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$) measurements. The cross-section morphologies of basalt fiber-reinforced epoxy composites were observed by scanning electron microscope (SEM). Also, the surface properties of basalt fibers were determined by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). From the results, it was observed that acid treated basalt fiber-reinforced composites showed significantly higher mechanical interfacial properties than those of untreated basalt fiber-reinforced composites. These results indicated that the hydroxyl functional groups of basalt fibers lead to the improvement of the mechanical interfacial properties of basalt fibers/epoxy composites in the all array direction.

• Journal of Information Display
• /
• v.4 no.3
• /
• pp.1-5
• /
• 2003

Laser-Induced Thermal Imaging (LITI) is a laser addressed patterning process and has unique advantages such as high-resolution patterning with over all position accuracy of the imaged stripes of within 2.5 micrometer and scalability to large-size mother glass. This accuracy is accomplished by real-time error correction and a high-resolution stage control system that includes laser interferometers. Here the new concept of hybrid system that complement the merits of small molecule and polymer to be used as an OLED; our system can realize easy processing of light emitting polymers and high luminance efficiency of small molecules. LITI process enables the stripes to be patlerned with excellent thickness uniformity and multi-stacking of various functional layers without having to use any type of fine metal shadow mask. In this study, we report a full-color hybrid OLED using the multi-layered structure consisting of small molecules and polymers.

• Journal of the Korean Chemical Society
• /
• v.61 no.6
• /
• pp.352-358
• /
• 2017

The addition of alginic acid, a natural polysaccharide, to improve the wettability and the reduction of protein adsorption of hydrogel contact lenses. Hydrogel contact lenses were manufactured with various monomers such as 2-methacryloyloxyethyl phosphorylcholine (MPC) and NVP (N-Vinyl-2-pyrrolidone). Alginic acid was added by by the initial mixing method and the interpenetrating polymer networks(IPN) method. Properties of contact lens such as contact angle, oxygen permeability, and protein adsorption amount were evaluated. The oxygen permeability and wettability of the IPN-treated alginate samples were higher than those of the samples that were not treated with IPN. The physical properties were improved as the concentration of IPN-treated alginic acid increased. Protein adsorption decreased by the addition of alginic acid and further decreased with IPN. In particular, contact lenses containing MPC and NVP significantly decreased protein adsorption. Therefore, the effect of alginate on the functional improvement of contact lens was confirmed.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.61-68
• /
• 2003

In this study, we have investigated the preparation of mixed bead and fiber type hybrid ion-exchanger for recovering nickel ion from plating rinse water. There was little dependence of adsorption capacity for nickel ion on the mixing ratio of resin type and fiber type of ion exchangers. However, it increased with increasing the resin content in the mixed bed. It was shown that the data Langmuir and Freundlich's adsorption isotherm model were well fitted to the linear. Affinity between the functional groups in the ion exchanger and nickel ion in the process was confirmed. The pressure drop decreased with increasing the number of stage in the multistage bed, but it increased with increasing the resin content in the mixing bed. The initial breakthrough time in the multistage bed was short due to the increase of number of stage in the continuous process. It was found that the final breakthrough time of the multistage bed was little changed. The breakthrough time decreased with increasing the amount of fibrous ion exchanger in the mixed bed. The maximum adsorption capacities of the mixed and multistage beds were 2.51 meq/g and 2.69 meq/g, respectively. The desorption time for the nickel ion with $1N H_2SO_4$ solution was lower than 10 minutes and the yield of desorption was greater than 98 percent.