• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.84-87
• /
• 2016

In this paper, a receiver for wireless power transfer is proposed. The receiver consists of a 100 W rectifier in 1.8 MHz frequency band, and a constant current charger. In particular, two kinds of protection circuits are installed in the rectifier. They are a over-voltage protection circuit which block the input voltages greater than 30 V and a active-dummy load which maintains the receiver input impedance by automatically consuming the remaining input power. The constant current charger is designed to charge the battery with a charging current of up to 1 A. A wireless charging system is fabricated using the proposed receiver. The system is composed of a 130 W transmitter, two magnetic resonator, and proposed receiver for charging a 48 V Li-Ion battery using the coupled magnetic resonance method. By the measurement result, the system efficiency is about 54 %.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.317-323
• /
• 2013

In this paper, 25W wireless power transmission(WPT) system using the coupled magnetic resonance is presented. The WPT system consists of a 100W class-F power transmitter, 1.7MHz magnetic resonators and a 40W full-bridge receiver using diodes. Especially, the transmit power control function using the 400MHz FSK communication between the transmitter and the receiver is adopted in the proposed system for the stable power transmission. Using the system and the power control function, the WPT system can be adopted in the various electronic devices and the commercialization of WPT system can be moved forward.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.2
• /
• pp.90-94
• /
• 2011

In this paper, the energy transfer is associated with high frequency band and try to analysis the rectifier circuit structure and characteristics and find ways to maximum efficiency. Input signal at 13.56MHz is converted output DC signal with the experiments and measurements. Rectifier cirsuits can be divided into the half-wave, full-wave, bridge rectifier circuit. Research to the present with the passive components are carried out with a focus on efficiency improvements. Factors affecting the efficiency of rectification is dependent on the characteristics of the device. In this experiment, about 70% efficiency can be measured. By using an improved device for high efficiency could be obtained higher efficiency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.883-891
• /
• 2013

In wireless smart phone charging scenario, the transmitter pad is larger than the size of the receiver pad. Thus, it is important to supply a constant power to the receiver regardless of its location. In this paper, we propose a new method to regulate the receiver's power by adjusting a drain bias of class E power amplifier. The proposed LF-band wireless power transfer system is as follows: a buck converter power supply which is controlled by a pulse width modulation(PWM) IC TL494, a class E amplifier using a low cost IRF510 power MOSFET, a transmitter coil whose dimension is $16cm{\times}18cm$, a receiver coil whose dimension is $6cm{\times}8cm$, and a full bridge rectifier using Schottky diodes. A measured performance show a maximum output power of 4 W and system efficiency of 67 % if we fix the bias voltage. If we adjust the bias voltage, the received power can be maintained at a constant power of 2 W regardless of receiver pad location.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.393-401
• /
• 2018

In this paper, a rectifier for WPC / A4WP wireless power transmission is designed. The proposed rectifier supports both WPC (Wireless Power Consortium) and A4WP (Alliance For Wireless Power) and is designed with full-bridge rectifier. WPC transmits power at the frequency of 100kHz to 205kHz and A4WP at the frequency of 6.75MHz. Since the bridge rectifier uses a MOSFET instead of a diode, the reverse current flows and the efficiency is affected if the output voltage is higher than the input voltage. Therefore, we added the reverse current detector that detects the current flowing through the MOSFET and shut off the reverse current. The frequency discriminator is used because the rectifier has different frequency band. The proposed rectifier was designed using $0.35{\mu}m$ CMOS high voltage process. The input voltage is up to 18V and the rectifier operates at 100kH to 205kHz, 6.78MHz frequency. The maximum efficiency is 94.8% and the maximum power transfer is 5.78W.

• Smart Structures and Systems
• /
• v.18 no.5
• /
• pp.885-909
• /
• 2016

Advances in low-cost wireless sensing have made instrumentation of large civil infrastructure systems with dense arrays of wireless sensors possible. A critical issue with regard to effective use of the information harvested from these sensors is synchronized sensing. Although a number of synchronization methods have been developed, most provide only clock synchronization. Synchronized sensing requires not only clock synchronization among wireless nodes, but also synchronization of the data. Existing synchronization protocols are generally limited to networks of modest size in which all sensor nodes are within a limited distance from a central base station. The scale of civil infrastructure is often too large to be covered by a single wireless sensor network. Multiple independent networks have been installed, and post-facto synchronization schemes have been developed and applied with some success. In this paper, we present a new approach to achieving synchronized sensing among multiple networks using the Pulse-Per-Second signals from low-cost GPS receivers. The method is implemented and verified on the Imote2 sensor platform using TinyOS to achieve $50{\mu}s$ synchronization accuracy of the measured data for multiple networks. These results demonstrate that the proposed approach is highly-scalable, realizing precise synchronized sensing that is necessary for effective structural health monitoring.