• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.17-18
• /
• 2010

최근 전력변환기의 효율 증대를 위한 소프트 스위칭 및 동기형 DC/DC 컨버터에 대한 연구가 활발히 진행되고 있다. 따라서 본 논문에서는 동기형 Buck-Converter를 이용한 Full-Bridge DC/DC 컨버터의 ZVS 기법에 대하여 연구 하였으며, 제안된 방식의 타당성을 검증하기 위해 Psim을 이용한 시뮬레이션을 행하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.461-463
• /
• 1996

A FB-ZVS(Full Bridge Zero Voltage Switching) PWM DC/DC converter for electric vehicles is analyzed in this paper. The converter considered is a step-down DC/DC converter with the ratings of 3l2/I3.5V and 1.35kW. The steady state analysis of this converter is divided into six operating modes. Digital simulations using PSPICE are carried out to verify the steady-state analysis.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.53-56
• /
• 2008

In this paper, we propose the battery charging device for electric bicycle using photovoltaic power. DC voltage from the solar cells is low, it needs to be step-up by the power conversion device. The power conversion device applied to this paper is phase-shift full-bridge converter. This converter steps-up from 12${\sim}$22[Vdc] to 36[Vdc] for charging the battery of electric bicycle. Phase-shift full-bridge converter(PSFB) can obtain twice as much DC voltage compared with half-bridge converter, thus it has lower current stress less than half-bridge converter. It is simulated and tested the battery charging device using photovoltaic power.

• 한국전자통신학회논문지
• /
• 제18권4호
• /
• pp.617-624
• /
• 2023

최근, 전자 제품의 소형화와 저소비전력화 및 향상된 효율과 역률개선이 큰 관심 사항이 되고 있다. 본 논문에서는 PWM 제어기반의 AC-DC 컨버터를 설계, 제작하였다. AC-DC 컨버터는 하나의 정류회로와 하나의 출력전압 제어 회로가 직렬로 연결되는 구조로 설계하였으며, 정류회로는 다이오드 기반 단상 전파전류 회로, 출력전압 제어 회로는 PWM 제어기반의 DC-DC 변환 회로를 적용하였다. PWM 제어를 위한 주 제어장치로 아두이노를 이용하였으며, LCD를 출력 단에 구성하여 제어 결과를 확인할 수 있도록 하였다. 시험회로를 통한 반복 실험들을 통해서 오실로스코프와 LCD에 디스플레이 되는 출력전압과 목표 출력전압의 오차를 확인하였으며, 오실로스코프 측정값을 기준으로 약 5%의 오차율을 보임으로써 제안된 설계 방법론의 유효성을 확인할 수 있었다.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.673-679
• /
• 2010

Input-series-output-parallel (ISOP) connected DC-DC converters enable low voltage rating switches to be used in high voltage input applications. In this paper, a DSP is adopted to generate digital phase-shifted PWM signals and to fulfill the closed-loop control function for ISOP connected two full-bridge DC-DC converters. Moreover, a stable output current sharing control strategy is proposed for the system, with which equal sharing of the input voltage and the load current can be achieved without any input voltage control loops. Based on small signal analysis with the state space average method, a loop gain design with the proposed scheme is made. Compared with the conventional IVS scheme, the proposed strategy leads to simplification of the output voltage regulator design and better static and dynamic responses. The effectiveness of the proposed control strategy is verified by the simulation and experimental results of an ISOP system made up of two full-bridge DC-DC converters.

• 전력전자학회논문지
• /
• 제12권5호
• /
• pp.400-408
• /
• 2007

본 논문에서의 병렬제어를 이용한 8kW급 대용량 영전압/영전류 풀 브릿지 DC-DC 컨버터의 개발 결과를 보인다. 본 논문에서는 효율적인 시스템 구성을 위해 4-병렬 단위 모듈 운전을 제안한다. 각 단위모듈은 위상 천이 풀 브릿지를 채택하고, ZVZCS 운전을 위해 간단한 보조 회로를 2차측에 추가하였다. ZCS를 위한 보조 회로 동작 로직은 환류 모드 구간에서 1차측 전류를 제거하도록 구현하였다. 또한 병렬 운전시의 출력 전류의 균등 제어를 위해 위상천이로직을 활용한 Charge Control 방식을 적용하였다. 전압 제어기는 DSP TMS320LF2406을 활용하여 4 모듈의 출력전류 및 출력전압을 A/D로 입력받아 구현하였다. 개발된 컨버터는 차량에 설치되는 고속 발전기용 전력 변환기에 장착되었으며, 구축된 모니터링 시스템으로 고속 발전기의 실제 운전 조건에서 데이터를 획득하여, 분석을 통해 그 성능을 입증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.986-989
• /
• 2002

This paper proposes a new single stage power factor correction (PFC) full bridge converter which operates at continuous conduction mode(CCM). The proposed single stage PFC consists of typical zero voltage switching(ZVS) full bridge DC/DC converter, two transformer auxiliary windings, and two small inductors, and two diodes. Neither additional active switch nor any control circuit are added for PFC resulting in very low cost. The proposed converter provides input power factor correction with CCM control and tight output voltage regulation. All switching devices are operated under ZVS with minimum voltage stress. Operation principle and analysis are explained and verified with computer simulation and experimental results on a 1.2kW, 100kHz prototype.

• Journal of Power Electronics
• /
• 제14권3호
• /
• pp.421-431
• /
• 2014

A DSP-based self-adaptive proportional-integral (PI) controller to control a DC-DC converter is proposed in this paper. The full-bridge topology is adopted here to obtain higher power output capability and higher conversion efficiency. The converter adopts the zero-voltage-switching (ZVS) technique to reduce the conduction losses. A parallel secondary active clamp circuit is added to deal with the voltage overshoot and ringing effect on the transformer's secondary side. A self-adaptive PI controller is proposed to replace the traditional PI controller. Moreover, the designed converter adopts the constant-current and constant-voltage (CC-CV) output control strategy. The secondary active clamp mechanism is discussed in detail. The effectiveness of the proposed converter was experimentally verified by an IGBT-based 10kW prototype.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.363-366
• /
• 1996

A FB-ZVS(Full Bridge Zero Voltage Switching) PWM DC/DC converter for electric vehicles is simulated and implemented in this paper. The converter considered is a step-down DC/DC converter with the ratings of 312/13.5V and 1.35kW. The steady state operation of this converter is divided into six operating modes in case of continuous current mode and eight operating modes in case of discontinuous current mode. Digital simulations using PSpice are carried out to verify the steady-state analysis. A prototype converter was built in the laboratory. MOSFETs were used for swithching devices and fast recovery diodes to reduce the charge storage problem of a pn-junction.

• Journal of Power Electronics
• /
• 제18권4호
• /
• pp.975-984
• /
• 2018

This work presents a high efficiency phase shifted full bridge (PSFB) DC-DC converter for use in the second stage of a battery charger for neighborhood electrical vehicle (EV) applications. In the design of the converter, Lithium-ion battery cells are preferred due to their high voltage and current rates, which provide a high power density. This requires wide range output voltage regulation for PSFB converter operation. In addition, the battery charger works with a light load when the battery charge voltage reaches its maximum value. The soft switching of the PSFB converter depends on the dead time optimization and load condition. As a result, the converter has to work with soft switching at a wide range output voltage and under light conditions to reach high efficiency. The operation principles of the PSFB converter for the continuous current mode (CCM) and the discontinuous current mode (DCM) are defined. The performance of the PSFB converter is analyzed in detail based on wide range output voltage and load conditions in terms of high efficiency. In order to validate performance analysis, a prototype is built with 42-54 V / 15 A output values at a 200 kHz switching frequency. The measured maximum efficiency values are obtained as 94.4% and 76.6% at full and at 2% load conditions, respectively.