• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.236-245
• /
• 2000

A laboratory scale fluidized bed reactor was developed to treat the combustion characteristics of some fuels (wood, paper sludge, refuse derived fuel). The aims were to introduce the means of experiment and interpretation of the results and finally determine the particle characteristics on the pyrolysis and combustion process of the fuel. A single particle combustion process in the fluidized bed was closely observed. Understanding experimental facility characteristics and determining parameters were also carried out. The fuel combustion processes were observed by carbon conversion rate, recovery and mean carbon conversion time. They were estimated with the CO, $CO_2$ gas concentration monitored at the exit of the combustor. Fuel drying and pyrolysis process were governed by temperature distribution in the fuel particle. There was a significant overlap of the drying and devolatilization. However, transition process from devolatilization to char combustion seemed to be determined by mechanical solidity of the fuel particle after devolatilization process.

• Journal of Environmental Health Sciences
• /
• v.13 no.2
• /
• pp.51-63
• /
• 1987

We identified pyrolysis condition, effect of catalyzer and pyrolysis mechanism through contact decomposed method by adding Bentonite in waste plastic of hospital solid waste. The result from this study were summarized as the followings: 1. The optimum fuel oil were obtained when hospital wasted plastic (P.P) and Bentonite were mixed in the ratio of 30:1. 2. Maximum absorption wave of hospital wasted plastic (P.P) appeared at 2900cm$^{-1}$, 1480cm$^{-1}$, 1360cm$^{-1}$ and 1180 cm$^{-1}$ by FT-IR and the plastics were identified and confirmed. 3. Reaction temperature of hospital wasted plastic started at 360$\circ$C, proceed rapidly at 437.5$\circ$C and finished at 481$\circ$C. The residue was 0.729%. When bentonire was added started at 318$\circ$C, proceed rapidly at 399.5$\circ$C and finished at 449.3$\circ$C, the residue being 4.23%. 4. Pyrolysis products of hospital wasted plastic were about 90 kinds. The Main components were 2-Heptene-3-ethyl-4-trimethyl (27.4%), 1-Heptene-2-isobutyl-6-methyl (8.6%) and 1-Heptene decene (7.7%). There was little component difference at different temperature. This is the result from stability of decomposition product. 5. Pyrolysis efficiency increased by the addition Bentonire. 6. Some of the Environmental and Sanitary problems could be solved by the pyrolysis of hospital wasted plastic and the decomposed products were to be used as fuel oil.

• 한국연소학회:학술대회논문집
• /
• 2003.05a
• /
• pp.143-150
• /
• 2003

The synthesis gas generated in waste pyrolysis melting process which consists of pyrolysis of waste and melting process of ash is known to be an alternative fuel. Since the compositopn of synthesis gas is much different from other synthesis gases, the fundamental combustion characteristics are analyzed in this study. The radiation heat heat flux is used to estimate the heat flux from flames made by many combinations of fuel and oxidant supply. The results show that the synthesis gas needs much more amount of oxidant for equivalent heat flux to methane flame and the inverse diffusion flame type for synthesis gas burner is suitable for better radiation heat transfer.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.29-32
• /
• 2014

The practical route for disposal of sewage sludge becomes energy recovery by combustion after its ocean dumping is banned in 2012 in Korea. Due to the high moisture content, however, sewage sludge is required to be dried before transport and combustion. In this study, pyrolysis and combustion characteristics of dried sewage sludge was investigated in a small-scale fixed bed reactor in order to provide fundamental data for energy recovery of the fuel. As the first step of combustion, the primary products of pyrolysis were analyzed in a fixed bed reactor for the condensable volatiles (tar), non-condensable gases, and char. For the combustion characteristics, another fixed bed reactor was constructed to monitor the weight and temperature of the fuel particles during ignition and combustion under different air flow rates. The test results were used to derive the ignition and burning rates.

• Journal of Powder Materials
• /
• v.21 no.3
• /
• pp.222-228
• /
• 2014

Much research into fuel cells operating at a temperature below $800^{\circ}C$. is being performed. There are significant efforts to replace the yttria-stabilized zirconia electrolyte with a doped ceria electrolyte that has high ionic conductivity even at a lower temperature. Even if the doped ceria electrolyte has high ionic conductivity, it also shows high electronic conductivity in a reducing environment, therefore, when used as a solid electrolyte of a fuel cell, the powergeneration efficiency and mechanical properties of the fuel cell may be degraded. In this study, gadolinium-doped ceria nanopowder with $Al_2O_3$ and $Mn_2O_3$ as a reinforcing and electron trapping agents were synthesized by ultrasonic pyrolysis process. After firing, their microstructure and mechanical and electrical properties were investigated and compared with those of pure gadolinium-doped ceria specimen.

• Applied Chemistry for Engineering
• /
• v.20 no.2
• /
• pp.223-226
• /
• 2009

In this study, we investigated the recovery of copper and synthetic fuel from the waste wire by low temperature pyrolysis which can overcome problems of the recent incineration methods. Through thermal decomposition process of waste wire, we achieved the big advantage of getting usable resources as the forms of copper and fuel with a very high value. The TG/DTA and small-scale reaction experiments were carried out to determine an optimum temperature for waste wire pyrolysis. And the pyrolysis was done at 350, 450, and $550^{\circ}C$, respectively, and heating rate of the TG/DTA was $5^{\circ}C/min$ untill $700^{\circ}C$. The result shows that the optimum temperature range for dehydrochlorination of PVC was $280{\sim}350^{\circ}C$, as a lower temperature range than $400{\sim}550^{\circ}C$ of PE and PP. Practically over 95% of copper metal and synthetic fuel, which has the 8027 kcal/kg as a calorific value, were recovered from the waste wire samples.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.243-247
• /
• 2014

Spherical NiO-YSZ particles were synthesized by ultrasonic spray pyrolysis (USP). The morphology of the synthesized particles can be modified by controlling parameters such as precursor pH, carrier-gas flow-rate, and temperature of the heating zone. The synthesized spherical NiO-YSZ particles have rough surface morphology at high carrier-gas flow-rates due to rapid gas exhaustion and insufficient particle ordering. The Ni-YSZ cermet anode synthesized by ultrasonic spray pyrolysis at a flow rate of l L/min, with precursor solution at pH4, showed a higher maximum power density of 256 $mW/cm^2$ compared to a conventionally mixed Ni-YSZ anode (185 $mW/cm^2$) at $800^{\circ}C$. While the area-specific resistance of conventionally mixed Ni-YSZ anodes increases gradually with operation time (indicating performance degradation), the Ni-YSZ anode synthesized by USP does not exhibit any performance degradation, even after 500 h.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.37-42
• /
• 2009

This paper describes the fuel oil characteristics of mulching waste vinyl by indirect heating emulsion system. For the emulsion experiment of waste vinyl, the system is composed of melting furnace, the 1th pyrolysis furnace, and the 2nd pyrolysis furnace. The mulching waste vinyl is used for the fuel oil characteristics analysis of mulching waste vinyl. The refined oil, gasoline, and diesel oil are extracted and quantified to analysis the fuel oil characteristics. From the results of experiments, it has been shown that the production of fuel oil from mulching waste vinyl is possible using the emulsion system.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.185-192
• /
• 2002

A laboratory scale thermogravimetric analyser was developed to investigate the combustion characteristics of selected solid fuel(wood) in the highly preheated air. The aims are to introduce in the means of experimental determination of the solid fuel particle characteristics through the combustion process in the environment of highly preheated air. A nearly single particle combustion condition was reproduced in a thermogravimetric analyser and regenerating combustor. For a fuel particle whose characteristic length was a few centimeter, the sub-processes of fuel drying, pyrolysis as well as the combustion of residual carbon were identified. Fluidized environment of carrier gas was selected as the major parameter which affect the combustion process.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.456-459
• /
• 2008

The 10t/d pyrolysis demonstration plant for waste tire recycling have been constructed and operated for commissioning of the plant. The plant have the tube reactor with chain conveyer attached disk. The reactor temperature is 500$\sim$600deg.C and pressure is -80$\sim$-100mmHg. Non-condensable gas is used as fuel for pyrolysis heat source.