• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.713-716
• /
• 2007

Interests have been focused to the renewable energy because energy cost of fossil fuel increased and global climate change caused by CO2 evolution became severe. To overcome these problems, it is essential to develop the energy conversion technologies of renewable resources. Therefore, production and utilization state of wood and woody waste was firstly investigated and then various technologies (pyrolysis, gasification, and combustion) converting the wood and woody waste to energy were summarized. Some case studies of woody waste utilization in europe was introduced with the policy of EU countries. Economical aspect of woody waste was compared with the current fossil fuels and the energy policy of wood and woody waste was suggested.

• 환경위생공학
• /
• 제15권4호
• /
• pp.98-104
• /
• 2000

Commercial rubber(IR, NR, BR), SBR, and tire were degraded by thermal degradation process. The oil yield of rubbers and tire ranges about 37~86%, it was increased with increase of operation temperature in pyrolysis. And the yield of pyrolytic oil was increased with increase of heating rate. The maximum oil yields of IR, NR, BR, SBR, and tire were 80, 73, 83, 86 and 55% each at $700^{\circ}C$ with a heating rate of $20^{\circ}C$/min, respectively. The pyrolytic oil components were consisted of about 50 aromatic compounds. The calorific value of purolytic oil of commercial rubber, SBR, and tire was measured by calorimeter, it was 39~40 kJ/g. The BET surface area of pyroblack was $47~63m^2/g$. The optimum condition of pyrolysis was operating temperature of $700^{\circ}C$ with heating rate of $20^{\circ}C$. Therefore, the pyrolytic oil and pyroblack are possible to alternative fuel and carbon black.

• 대한기계학회논문집B
• /
• 제33권2호
• /
• pp.116-123
• /
• 2009

Carbon black, activated carbon and carbon nanotube have been used as supporting materials for precious metal catalysts used in fuel cell electrodes. One-step flame synthesis method is used to coat 2-5nm Pt dots on flame-generated carbon particles. By adjusting flame temperature, gas flow rates and resident time of particles in flame, we can obtain Pt/C nano catalyst-support composite particles. Additional injection of hydrogen gas facilitates pyrolysis of Pt precursor in flame. The size of as-incepted Pt dots increases along the flame due to longer resident time and sintering in high temperature flame. Surface coverage and dispersion of the Pt dots is varied at different sampling heights and confirmed by Transmission electron microscopy (TEM), Energy-dispersive spectra (EDS) and X-ray diffraction (XRD). Crystalinity and surface bonding groups of carbon are investigated through X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.59-62
• /
• 2008

The performance behavior of solid oxide fuel cell using reformate gas as fuels was investigated. When the pre-reformate gas was used without steam, the maximum power density was 50% lower than that using H2. This may be due to carbon deposition caused by the pyrolysis of remaining hydrocarbons. However, when the steam was added, the maximum power density showed a relatively small variation according to reformate gas. When pre-reformate gas with steam was fed into anode, the SOFC showed the stable performance without sharp voltage drop during 10h operation.

• 응용화학
• /
• 제15권1호
• /
• pp.81-84
• /
• 2011

Platinum catalyst activity and stability is excellent in terms of fuel cells as a catalyst here. Although it is widely used, to compensate for the high price issue non-precious fuel cell catalysts are being developed. In this study, Co/PANi/CNT composite and non-precious as a catalyst for oxygen reduction was applied. Polyaniline on the interaction between cobalt and the oxygen reduction reaction and the structural characteristics observed in the impact and heat treatment was carried out according to the improved catalytic performance. Potential range is oxygen reduction reaction 0.55 V to 0.78 V(vs. NHE) after pyrolysis. Through this study, Co /PANi/CNT composites as a potential catalyst for fuel cells were non-precious.

• 한국응용과학기술학회지
• /
• 제35권2호
• /
• pp.540-559
• /
• 2018

액상 바이오연료를 생산할 수 있는 하수슬러지는 자국의 에너지 안보와 지속가능한 생산이 가능하고 경제적인 원료로 여겨지고 있다. 열화학적 기술은 하수슬러지를 에너지화, 연료화할 수 있는 가장 효과적인 방법이다. 일반적으로 하수슬러지는 수분 함량이 80% 이상으로 높은 금속 함량과 14 ~ 20 MJ/kg의 발열량을 갖고 있다. 본 논문에서는 하수슬러지를 활용한 액상 바이오연료를 생산하는 열분해 반응, 전이에스테르화 반응, 초임계 반응 기술에 대해 살펴보고자 한다. 또한, 하수슬러지 유래 액상 바이오연료의 연료적 특성과 액상 바이오연료와 관련한 국내 법에 대해 검토하였다.

• Journal of Biosystems Engineering
• /
• 제25권6호
• /
• pp.481-488
• /
• 2000

This study was initiated in order to find alternative fuel substituting for light oil the most common fuel for heating greenhouse. The tire oil used in this research was produced by pyrolysis process, one of the final products besides steel string and carbon black in which waste tires as a form of chopped pieces broken by shredding machine are heated up to 200~30$0^{\circ}C$ with maximum restraining of oxygen supply. In order to justify light oil equivalent qualities in tire oil combustion characteristics were defined in the way of comparing kinetic viscosities in the wide range of temperature flame sizes and exhaust gas components in the various combustion conditions. We found that kinetic viscosity of tire oil was lower than light oil by 1 to 2 cSt in the temperature range showing better flowing mobility in the fuel line of the burner and no significant difference in flame size between the two oils in the all combustion treatments. However much more NO and SO$_2$ were detected from the exhaust gases of tire oil than light oil combustions. In fact tire oil contains more nitrogen and total sulfur, by 25 times and 40 times respectively than light oil according to the composition analysis. Tolerable limit for SO$_2$discharge amount defined by the national air pollution standards is under 540ppm so tire oil combustion satisfies the requirement though. It is desirable if sulfur and nitrogen filtering process shall be added in the tire oil production line. Except the exhaust gas components all greenhouse heating qualities of tire oil including hot air temperature are very identical to those of light oil.

• Korean Chemical Engineering Research
• /
• 제61권4호
• /
• pp.591-597
• /
• 2023

Pakistan depends heavily on imports for its fuel requirements. In this experiment, catalytic pyrolysis of a blend of feedstock's consisting of date seed, wheat straw, and corn cob was conducted in a fixed bed reactor to produce oil that can be used as an alternative fuel. The main focus was to emphasize the outcome of important variables on the produced oil. The effects of operating conditions on the yield of bio-oil were studied by changing temperature (350-500 ℃), heating rate (10, 15, 20 ℃/min), and particle size (1, 2, 3 mm). Moreover, ZnO was used as a catalyst in the process. First, the thermal degradation of the feedstock was investigated by TGA and DTG analysis at 10 ℃/min of different particle sizes of 1, 2, and 3mm from a temperature range of 0 to 1000 ℃. The optimum temperature was found to be 450 ℃ for maximum degradation, and the oil yield was indicated to be around 37%. It was deduced from the experiment that the maximum production of bio-oil was 32.21% at a temperature of 450 ℃, a particle size of 1mm, and a heating rate of 15 ℃/min. When using the catalyst under the same operating conditions, the bio-oil production increased to 41.05%. The heating value of the produced oil was 22 MJ/kg compared to low-quality biodiesel oil, which could be used as a fuel.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.107-107
• /
• 2010

Hydrogen is an alternative fuel for the future energy which can reduce pollutants and greenhouse gases. Synthesis gas have played an important role of synthesizing the valuable chemical compound, for example methanol, DME and GTL chemicals. Renewable biomass feedstocks can be potentially used for fuels and chemical production. Current thermal processing techniques such as fast pyrolysis, slow pyrolysis, and gasification tend to generate products with a large slate of compounds. Lignocellulose feedstocks such as forest residues are promising for the production of bio-oil and synthesis gas. Pyrolysis and gasification was investigated using thermogravimetric analyzer (TGA) and bubbling fluidized bed gasification reactor to utilize forest woody biomass. Most of the materials decomposed between $320^{\circ}C$ and $380^{\circ}C$ at heating rates of $5{\sim}20^{\circ}C/min$ in thermogravimetric analysis. Bubbling fluidized bed reactor were use to study gasification characteristics, and the effects of reaction temperature, residence time and feedstocks on gas yields and selectivities were investigated. With increasing temperature from $750^{\circ}C$ to $850^{\circ}C$, the yield of char decreased, whereas the yield of gas increased. The gaseous products consisted of mostly CO, CO2, H2 and a small fraction of C1-C4 hydrocarbons.

• 공업화학
• /
• 제22권5호
• /
• pp.508-513
• /
• 2011

헴프(Hemp)는 빠른 성장과 재배가 용이한 특성을 가지고 있으며 전통적으로 인피(Bast)는 섬유산업에 이용되고 있다. 그러나 인피를 제외한 줄기(Stem)와 뿌리(Root)는 활용분야가 없어 대부분 부산물로서 폐기되고 있다. 이러한 헴프 부산물은 바이오-오일과 같은 바이오연료나 활성탄의 원료물질로 활용될 수 있다. 본 연구에서는 헴프 줄기, 뿌리 및 인피를 대상으로 열화학적 특성을 파악하였다. TGA를 이용해 열중량분석을 수행한 결과 헴프 부산물들의 분해영역은 대부분 $270{\sim}370^{\circ}C$ 라는 것을 확인하였다. TGA 분석으로부터 얻은 실험데이터는 미분법을 적용하여 전화율 변화에 따라 활성화에너지와 전지수인자를 계산하였다. 열분해반응에서 활성화에너지는 전화율 증가에 따라 증가하였다.