• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.43-49
• /
• 2013

This work investigated the effects of engine speed and injection timing on combustion and emissions characteristics in a partially premixed charge compression ignition (pPCCI) engine fueled with DME. pPCCI engine especially has potential to achieve more homogeneous mixture in the cylinder, which results in lower NOx and smoke emission. In this study single cylinder engine was equipped with common rail and injection pressure is 700 bar. Total injected fuel mass is 64.5 $mm^3$ per cycle. The amount of pilot injection of the entire injection 12.5% is tested. Results show that NOx emission is decreased while IMEP is increased as the retard of injection timing. Besides, NOx emissions are slightly rised as well as IMEP is increased with the increase of engine speed.

• 한국연소학회지
• /
• 제15권3호
• /
• pp.57-66
• /
• 2010

The purpose of this paper is to investigate the effects of fuel injection strategy and engine load on the structure and emissions characteristics of a DI diesel engine with 1.6L of piston displacement. In order to analyze the particulate matter (PM) and exhaust emissions characteristics in a direct injection diesel engine, the quantity of PM and exhaust emissions (including HC, CO and $NO_X$) were investigated under various injection strategies and engine loads. Two different injection strategies (one pilot/main injection and two pilots/main injection) was investigated under the various engine loads. A thermophoretic sampling method with a scanning electron microscope (SEM) were used to obtain the PM morphology (including primary particles, the size of the agglomerates, the number of agglomerates, the fractal dimension). The quantity of soot gradually increased with increasing engine load at both injection strategies. The primary particles in the PM agglomerates indicate that the average of the primary particle and radius of gyration increased as the engine load increased.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.99-105
• /
• 2011

This paper described the effect of the multiple injections on the emission characteristics and combustion stability in a common rail diesel engine. In order to investigate the influence of multiple injections in a passenger car diesel engine, the injection strategy was varied with pilot injection, post injection and one main injection at various conditions. Based on the experimental results, the combustion and emissions characteristics were analyzed for the various injection strategies such as main, pilot-main, double-pilot-main, double- pilot-main-post injection strategy. It is revealed that the $NO_X$, HC and CO emissions are reduced by double pilot and post injection at medium load, however, soot emission is increased. Also, in the case of multiple injection, the combustion pressure is increased smoothly near the TDC and the coefficient of variation and fuel consumptions are decreased.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.247-250
• /
• 2009

Awareness of resource conservation and pollution prevention has been continually increasing. The proven benefits from CFRP's unique combination of light weight and high strength compare to conventional material is well suited for minimizing fuel consumption during vehicle in particular rail operation. Responding the awareness, this work intends to study CFRP's recycling method that is not only technical performance but also environmental view point. According to prior work of technical performance test, this work aims at quantifying the footprint of energy and GHG derived from the two appreciated performance of pyrolysis and acids recycling methods. The streamline LCA is the concept for systematic assessment. The boundary is scoped at the recycling activity, consequently, the data in and out from the specific target activity are obtained under the gate to gate data collection. Its function is recovery carbon fiber. To count and compare function, functional unit is set at 60% of recycling rate. Korea database is mainly source for acquiring the footprint of both. The numerical results presented that the energy footprint of acids and pyrolysis is 164.95 and 1,199.88 MJ-eq., respectively. Meantime, the GHG footprint of is 1,196.22 and 5,916.08 g CO2 eq. for acids and pyrolysis. In summary, the acids recycling method is, in regarding the environmental performance, better than pyrolysis recycling method.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권4호
• /
• pp.403-411
• /
• 2012

This study presents the nano-sized particle emission characteristics from a small turbocharged common rail diesel engine applicable to prime and auxiliary machines on marine vessels. The experiments were conducted under dynamic engine operating conditions, such as steady-state, cold start, and transient conditions. The particle number and size distributions were analyzed with a high resolution PM analyzer. The diesel oxidation catalyst (DOC) had an insignificant effect on the reduction in particle number, but particle number emissions were drastically reduced by 3 to 4 orders of magnitude downstream of the diesel particulate filter (DPF) at various steady conditions. Under high speed and load conditions, the particle filtering efficiency was decreased by the partial combustion of trapped particles inside the DPF because of the high exhaust temperature caused by the increased particle number concentration. Retarded fuel injection timing and higher EGR rates led to increased particle number emissions. As the temperature inside the DPF increased from $25^{\circ}C$ to $300^{\circ}C$, the peak particle number level was reduced by 70% compared to cold start conditions. High levels of nucleation mode particle generation were found in the deceleration phases during the transient tests.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2910-2915
• /
• 2008

This paper was investigated the behaviors of the engine and combustion phenomena for various LPG compositions in the semi-return type system, which is not recircurated to LPG tank through furl rail, applied LPi engine during a cold idle condition and including a cold start of the engine. Cyclic HC and NOx emissions were measured at exhaust port to examine their formation mechanical and reduction mechanical with fast response gas analyzers. Various ignition timing is experimented to study the characteristics of combustion phenomena, HC/NOx emissions during fast idle. Also, this study was investigated start delay time, cylinder pressure, HC/NOx emissions, Mass Fraction Burned, starting time to evaluate performance of transient cold startability. Compared to the return type system, the semi-return type system have advantages in point of production cost and equivalent performance of engine starting time and pressure settling time.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.134-139
• /
• 2011

Recent research has focused on engine combustion technology as well as application of after-treatment in order to comply with emission regulation. However, it is much more efficient way to control emissions from engine itself and furthermore research on engine control will provide the direction of after-treatment technology in future. Furthermore, emission standard regulation for passenger diesel vehicles has been stringent compared to others and nano-particles will be included in EURO6 regulation in Europe and similar emission standard will be introduced in Korea. A 3.0 liter high speed diesel engine equipped with by CRDI system of 160MPa injection pressure, and an intake/exhaust system of V type 6 cylinder turbo-intercooler was applied. The injection duration and injection quantity, pilot injection types which are related to CRDI and air/fuel ratio control applied by EVGT were changed simultaneously. Standard experiment procedure constituted dilution apparatus and CPC system to collect nano-particles and these test results were compared with regulated materials of CO, HC, NOx and investigated their relations and characteristics of nano-particles.

• 대한기계학회논문집B
• /
• 제38권2호
• /
• pp.129-137
• /
• 2014

본 연구에서는 바이오디젤연료 혼합비변화에 대한 디젤엔진의 배기특성에 대해 조사하였다. 실험에 사용된 연료는 경유와 바이오디젤(폐식용유) 혼합연료 BD3, BD5, BD20, BD50 및 BD100을 사용하였으며, 실험변수로서 분사압력(${\Delta}p_{inj}$)을 400bar, 600bar, 800bar, 1000bar 및 1200bar로 설정하였다. 분사압력과 바이오디젤 혼합연료 혼합비에 따른 정량적인 NOx와 Soot의 배기특성 해석을 위하여 통계학에 기초한 피어슨 상관계수와 스피어만 상관계수의 개념을 도입하였다. 본 연구의 결과로서 실험 조건 전체에 대한 피어슨 상관계수는 -0.732, 스피어만 상관계수는 -0.724로 NOx와 Soot 발생의 상관관계가 선형적이다. 특히 분사압력 800bar 조건에서 피어슨 상관계수가 -0.089으로 NOx와 Soot 배출량 상관관계가 0에 가깝기 때문에, 바이오디젤 연료 혼합비 제어를 통한 NOx와 Soot의 동시저감이 가능하다고 판단된다.

• 한국수소및신에너지학회논문집
• /
• 제25권5호
• /
• pp.533-540
• /
• 2014

The remanufacturing industry for automotive parts is a major issue which affects the environment protection and CO2 reduction throughout the world. Beside this, remanufacturing technologies of worn-out diesel engines have been developing to make as close to new as possible. In this study, the characteristics of the engine-power output and exhaust emissions of remanufactured diesel engine by hydrogen enrichment are evaluated by measuring the engine and vehicle test. Moreover, with worn-out diesel engine and first generation common-rail engine, we compared by testing their characteristics, resulting in the restoration of engine-power output more than 93%, as well as marvelously reduces the THC and NOx emission. At a guess, high pressure injection of diesel increases fuel atomization characteristics with excellence combustion efficiency, resulting in reduction of THC emission. Also, rapid cooling of EGR decreases combustion temperature, resulting in reduction of NOx emission. Consequently, these remanufacturing for diesel engine enables worn-out diesel engine to have restoration to the original state. Simultaneously achieved 2 goals called that CO2 emission reduction and protection of environment by remanufacturing engine.

• 대한기계학회논문집B
• /
• 제34권4호
• /
• pp.417-422
• /
• 2010

1.7L 커먼 레일 직접 연료분사 디젤엔진과 초저유황 스웨덴 디젤 연료를 이용하여 연료분사시기 8.5CA BTDC~0.5CA BTDC 와 배기가스 재순환률 37%, 43%, 48% 영역에서 실험을 수행하였다. 각각의 배기가스 재순환률에 대하여 연료분사시기가 지각됨에 따라 매연과 질소산화물이 동시에 저감되나 탄화수소와 일산화탄소는 증가하는 저온 디젤 연소영역에 있음을 확인하였다. 탄화수소를 가스크로마토그래프와 불꽃 이온 검출기를 사용하여 종 분석을 수행하였으며, 연료분사시기가 지각될수록, 그리고 배기가스 재순환률이 증가할수록 Partially burned HC, 알켄의 비율이 증가하였다. Partially burned HC 중에서 에텐이, 그리고 Unburned HC 중에서 노말 운데케인이 가장 많이 배출되었다. 이 두 개의 탄화수소 종은 촉매 연구에 사용되는 벤치 플로우리액터 시험에서 대표적인 탄화수소 종으로 사용할 수 있다.