• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.76-84
• /
• 2010

The aim of this study is to analyze the effect of the ethanol blending in diesel-ethanol blended fuels on the spray and combustion characteristics in a common-rail four-cylinder diesel engine. For the analysis of the spray characteristics, the spray images were obtained using a high speed camera with metal-halide lamps. From these spray images, the macroscopic spray characteristics such as the spray tip penetration and spray cone angle were investigated. Also, the combustion characteristics including the combustion pressure and the rate of heat release were studied with the analysis of the exhaust emissions in diesel-ethanol blended fuel driven diesel engine. It can be confirmed from the experiment on spray characteristics of diesel-ethanol blended fuels that the increased ethanol blending ratio induced the decrease of the spray tip penetration after the end of the injection. The spray cone angle slightly increased by the blending of ethanol fuel. In the experiment on atomization characteristics, the ethanol blending caused the improvement of the diesel atomization performance. On the other hand, at the same engine load condition, the increase of the ethanol blending ratio lead to lengthen the ignition delays, and to decrease the peak combustion pressure and the rate of heat release. Totally, the combustion and emission characteristics of ULSD and DE10 showed similar characteristics. However, in the case of DE20, CO and HC rapidly increased, and $NO_x$ decreased. It can be believed that 20% ethanol disturbed the combustion of diesel-ethanol blended fuel due to the low cetane number and evaporation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권4호
• /
• pp.379-387
• /
• 2011

최근 디젤엔진에서 엔진성능향상 및 배출가스저감을 위해 저압 EGR시스템에 대하여 연구개발이 활발히 진행되고 있다. 저압 EGR시스템은 EGR율에 따라 과급압력이 영향을 받지 않기 때문에 PM을 최소 화하면서 $NO_x$를 저감할 수 있는 장점을 갖고 있다. 본 연구에서는 2.0L급 고속직분사방식의 엔진에서 출력 및 연비저하로 EGR적용이 어려운 엔진회전수 2000 rpm, BMEP 1.0 MPa, 과급압력 181.3 kPa인 중부하 운전영역에서 서로 다른 EGR시스템에 따른 엔진성능 및 배출가스 특성을 실험적으로 연구하였다. 그 결과로서 기존의 고압 EGR시스템 또는 배압조절밸브를 사용하는 저압 EGR시스템에 비하여 ETC를 적용한 저압 EGR시스템이 $NO_x$ 배출특성은 큰 차이가 없는 반면에, 연비 및 열효율이 향상되고 PM 저감에 연소효과를 나타내고 있음을 확인하였다.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.73-80
• /
• 2002

Dimethyl ether (DM) is one of the most attractive alternative fuel far compression ignition engine. Its main advantage in diesel engine application is high efficiency of diesel cycle with soot free combustion though conventional fuel injection system has to be modified due to the intrinsic properties of DME. Experimental study of DME and conventional diesel spray employing a common-rail type fuel injection system with a 5-holes sac type injector (hole diameter 0.168 ㎜/hole) was performed in a high pressure chamber pressurized with nitrogen gas. A CCD camera was employed to capture time series of spray images followed by spray cone angles and penetrations of DME were characterized and compared with those of diesel. Under atmospheric pressure condition, regardless of injection pressure, spray cone angles of the DME were wider than those of diesel and penetrations were shorter due to flash boiling effect. Tip of the DME spray was farmed in mushroom like shape at atmospheric chamber pressure but it was disappeared in higher chamber pressure. On the contrary, spray characteristics of the DME became similar to that of diesel under 3MPa of chamber pressure. Hole-to-hole variation of the DME spray was lower than that of diesel in both atmospheric and 3MPa chamber pressures. At 25MPa and 40MPa of DME injection pressures, regardless of chamber pressure, intermittent DME spray was observed. It was thought that vapor lock inside the injector was generated under the two injection pressures.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.985-993
• /
• 2012

In this paper, a new method is proposed to estimate the sound pressure generated from gasoline direct injection (GDI) engine. There are many noise sources as much as components in GDI engine. Among these components, fuel pump, fuel injector, fuel rail, pressure pump and intake/exhaust manifolds are major components generated from top of the engine. In order to estimate the contribution of these components to engine noise, the total sound pressure at the front of the engine is estimated by using airborne source quantification (ASQ) method. Airborne source quantification method requires the acoustic source volume velocity of each component. The volume velocity has been calculated by using the inverse method. The inverse method requires many tests and has ill-condition problem. This paper suggested a method to obtain volume velocity directly based on the direct measurement of sound intensity and particle velocity. The method is validated by using two known monopole sources installed at the anechoic chamber. Finally the proposed method is applied to the identification and contribution of noise sources caused by the GDI components of the test engine.

• 한국산림과학회지
• /
• 제94권3호통권160호
• /
• pp.135-145
• /
• 2005

본 논문의 목적은 1929년 일제시대 경성부에서 소비된 임산연료의 구성별 특성과 유통경로를 밝히는 것이다. 그 결과를 요약하면 첫째, 1929년 경성부에서 소비된 1호 평균 임산연료의 중량은 경기도의 일반 군에 비해 약 1/3 수준에 불과했으나 열량이 높은 장작과 숯의 소비량은 상대적으로 매우 높았다. 둘째, 임산연료의 최대 공급지는 한강 수운을 이용할 수 있는 강원도와 경기도의 한강변(42.6%)이었고, 그 다음으로 철도를 이용한 경기도 북부와 기타 지역(29.5%), 도로를 이용한 경성부 인근 지역(27.9%)의 순이었다. 셋째, 한강을 이용한 임산연료의 운송지역은 뚝섬(43.0%)과 구용산 마포(45.6%)로 이원화되어 있었고, 철도에 의한 운송은 경성역이 전체의 72.2%라는 압도적인 위치를 차지하고 있었다. 넷째, 경성부의 소비지에 도착한 임산연료의 대부분은 상설시장이 아닌 임시로 형성된 땔감 시장에서 거래되었다.

• 한국분무공학회지
• /
• 제10권1호
• /
• pp.24-34
• /
• 2005

Injection technology is one of the important technologies in a diesel engine. Many studies have done on the injection system. In this study, the fuel chamber geometry, the orifice ratio and the needle lift of the injection valve for a marine diesel engine are varied, and simulated. The result shows that the nozzle hole size has influence on the rail pressure and injection duration sensitively. The decrease of the static pressure at the nozzle hole entrance and the increase of the dynamic pressure on the outlet surface are occurred with the increase of the nozzle hole diameter. The highest dynamic pressure of the outlet was occurred at the needle lift of 0.4mm and the nozzle hole diameter of 0.328mm in this test nozzle.

• 한국연소학회지
• /
• 제15권4호
• /
• pp.53-57
• /
• 2010

The purpose of the present work is to investigate the effect of gasoline-premixing on a combustion and emissions characteristics in a compression ignition engine. For studying combustion characteristics, a combustion pressure and rate of heat release (ROHR) were measured using a single-cylinder DI compression ignition engine with a common-rail injection system and premixed fuel injection system. In addition, exhaust emissions characteristics were studied using emission analyzers and smoke meter. The experimental results showed that the case of gasoline-premixing had longer ignition delay and lower combustion pressure compared to the cases of diesel direct injection. Furthermore, premixed gasoline-air mixture reduced NOx emissions due to low peak of ROHR.

• 한국분무공학회지
• /
• 제5권4호
• /
• pp.33-39
• /
• 2000

The behavior of the 2-stage spray was studied by using the schlieren method with the high pressure common-rail injection system. The spray injected 2 times with the interval of $0.3ms{\sim}1.5ms$ between the 1st and the 2nd spray in a modeled combustion chamber of constant volume bomb. In this case, the quantity of injected fuel of 1st and 2nd also changed. The schlieren photograph shows that the 2nd spray goes further away than the 1st spray when the quantity of the 1st spray is less than that of the 2nd spray. The dispersion of the vapour to the combustion chamber is not affect in a 10% of 1st spray quantity. When the 1st spray quantity is more than the 2nd spray, the vapour scattering of spray is good.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.269-273
• /
• 2005

Since adding design elements to train manufacturing technologies creates addition of high value, it is necessary to develop design for FRT with increased convenience of transportation by rail, which is a new paradigm. Therefore, an evaluation model for increasing convenience of the interior of FRT should draw the requirements of such design and their importance and supply logical basis for setting standards of establishing convenience of system and evaluating and measuring them. In order to evaluate design elements such as interior layout and arrangement of facilities, the model, of which commonness and subjectivity have been verified, should be presented. In consequence, this study going to more concretely focus on new values and sensitive technologies, application of availability and visual communication.

• 한국산업융합학회 논문집
• /
• 제21권2호
• /
• pp.45-51
• /
• 2018

Compression ignition diesel engine can reduce carbon emission than gasoline engine in case of high efficiency, output and durability. So, compression ignition diesel engine is used in various fields such as automobiles, industries and so on. Due to reducing of emission exhaust by Developing of injection and combustion type of diesel engine, emission of pollution substance is developed compared the past. Moreover, its efficiency and reduce of carbon emission is better than gasoline engine and it is used in power source of industries, transports and others because of its high efficiency and durability nowadays. In this study, we experiment by making and designing of compression ignition diesel engine witch has air-cooling, 2 cylinder and 2 strokes.