연소과정 중에 발생하는 질소산화물을 저감하는 기술인 MILD 연소에 대하여 연료노즐과 공기노즐의 위치와 공기유량을 변화하면서 나타나는 연소특성을 수치해석을 통하여 연구하였다. 본 연구의 MILD 연소로는 연료노즐과 공기 노즐 사이에 연소배기가스의 배출구가 있는 연소로를 이용하였다. 공기노즐은 8개, 연료노즐은 4개를 사용하였다. 연료노즐이 연소로 중앙 부근에 위치한 연소로의 경우에 공기유량이 적을 때는 연소반응대가 연료노즐에서부터 연소로 벽면으로 치우치게 되지만 공기유량이 커지면 연소반응대가 연료노즐 측에서 시작하여 연료노즐 상부로 형성된다. 공기노즐이 연소로 중앙부분에 위치한 경우에 공기유량이 적을 때는 연소반응대가 공기노즐 부근에서 시작하여 연소로 벽면으로 치우치지만 공기유량이 증가하면 연소반응대가 연료노즐 측으로 옮겨가게 된다. 두 가지 경우 모두 공기유량이 증가하면 연소반응대에서 최대온도가 증가하고 따라서 배기가스에서의 NOx 농도가 증가한다. 두 가지 노즐 위치에서의 NOx 생성을 비교해 보면 공기노즐이 연소로 중앙에 위치한 경우가 연료노즐이 연소로 중앙에 위치한 경우보다 NOx 농도가 현저히 적음을 알 수 있었다. 본 연구의 결과로부터 NOx 저감과 연료의 미연가스 배출을 감안할 때 공기노즐이 연소로 중앙에 위치하고 이론공기량에 해당하는 공기량을 분출할 때 NOx 생성에 가장 효과적임을 알 수 있었다.
The breakup of liquid jet is the result of competing, unstable hydrodynamic forces acting on the liquid jet as it exit the nozzle. The nozzle geometry and up-stream injection conditions affect the characteristics of flow inside the nozzle, such as turbulence and cavitation bubbles. A set of calculation of the internal flow in a single hole type nozzle were performed using a two dimensional flow simulation under different nozzle geometry and up-stream flow conditions. The calculation showed that the turbulent intensity and discharge coefficient are related to needle position. The diesel nozzle with sharp inlet under actual engine condition has possibility of cavitation, but round inlet nozzle has no possibility of cavitation.
The synergistic effect of ethylene/propane mixture on soot formation is studied experimentally using a concentric co-flow diffusion burner, which provides the stratified fuel mixture. The soot volume fraction, soot particle diameter, number density and PAH concentrations are measured with various fuel supply configurations and compared to the homogeneously mixed case. When propane is supplied through the inner nozzle, an increase of soot formation is observed. However, when propane is supplied through the outer nozzle, a decrease is observed. The reaction path of PAH's formed from the pyrolysis process of propane is likely to be responsible to the observed differences. When propane is supplied through the outer nozzle, PAH's are formed in the relatively near oxidation region and exposed to the oxidization environment; on the other hand, when propane is supplied through the inner nozzle, PAH's are not likely to be oxidized and thus get involved in soot formation process. The synergistic effect in ethylene/propane diffusion flames is found to be affected not only by the com position of the mixture but also by the way of mixing.
본 연구에서는 형식이 각기 다른 3종류의 미분무수 노즐을 사용하여 방사높이와 화염의 위치 변화에 따른 소화성능 실험과 포 소화약제를 혼합한 소화성능 실험을 수행했다. 소화성능 실험에서는 미분무수 노즐의 높이를 4m, 3.5m, 3m로 변화를 주었으며 연료 팬을 노즐 중심으로부터 0m, 0.5m, 1m의 변화를 주었다. 포 소화약제는 3%형 AFFF(Aqueous Film Forming Foam)를 사용하였다. 실험결과 개구부의 유무는 소화에 미치는 영향이 적었으며, 포 소화약제를 혼합한 미분무수의 소화성능은 약제를 혼합하지 않은 경우에 비하여 우수하였다.
연소과정 중에 발생하는 질소산화물을 저감하는 기술인 MILD 연소로는 연소용 공기 및 연료로 고온의 배기가스가 유입되는 양에 따라 질소산화물 저감 특성이 많은 영향을 받는다. 일반적인 MILD 연소로는 연료와 연소용 공기는 수직 상향방향이고 배기가스는 수직하향 방향으로 흐르면서 배기가스가 유입되는데 이러한 형태보다 더욱 배기가스의 유입량을 증가시키기 위한 방법으로 동심원관형태의 MILD 연소로를 사용하고 있다. 본 연구에서는 바깥 원통의 배기가스 통로에서 안쪽 원통의 연소통로 사이에 연결관을 설치하고 배기가스를 유입하기 위한 공기노즐을 동심원관 형태로 설치하여 공기분사속도, 노즐 직경, 배기가스측 압력과 연소로측 압력 차이의 변화에 따른 유입량 특성을 수치해석을 통해 살펴봄으로써 MILD 연소로에서 더욱 적극적인 배기가스의 유입량 특성을 파악하는 것을 연구하였다. 공기노즐 분사속도의 증가에 따라 유입량은 속도의 제곱근에 비례하는 것을 알았고 배기가스 측과 연소로 측의 압력차의 크기에 선형적으로 감소하는 것을 관찰하였다. 공기노즐 출구 위치의 변화는 유입량 변화에 큰 영향이 없음을 알 수 있었다.
30톤급 액체로켓엔진용으로 개발된 일체형 재생냉각 연소기는 연료를 확대노즐부의 중간에서 공급하는 방식으로 설계되었으며, 노즐 끝단에서 공급되는 방식에 비해 냉각유로는 복잡해지지만 열유속이 상대적으로 낮은 확대노즐부의 냉각유량을 줄임으로서 압력손실을 감소시키는 동시에 공급라인을 포함한 연소기 전체 외경이 줄어들어 엔진 구성에 유리한 장점을 있다. 본 연구에서는 이와 관련한 연료링과 양 방향 냉각 채널, 그리고 연결/분기 유로에 대해 수치해석을 통한 세밀한 설계검토를 수행하였다.
Experimental investigation of unsteady impinging diesel spray on the flat plate have been carried out using high speed camera and Malvern system. The density ratios of ambient gas to diesel fuel were varied using $N_2$ and Ar gas in the case of 14.9, 21.2, 28.4, 35.1, 40.4, and 50.1. With the increase of gas density ratio, the radial penetration is decreased due to the resistance of the ambient gas. With the increase of the gas density ratio and the distance between nozzle tip and flat plate, the height of spray is increased due to the entrance and circulation. With the increase of gas density ratio, SMD is decreased on the nearby position at the center of flat plate, but SMD is increased on the far position. As the distance between nozzle tip and flat plate is increased, SMD is always decreased.
The beneficial aspects of applying emulsion fuels to combustion systems may be due to the changes of fuel properties which lead to the enhanced atomization characteristics. The spray characteristics of water/oil emulsified fuel injected from the pressure-swirl(simplex) atomizer using for oil burner were investigated. Four different water contents from 10 to 40 % by volume at 10% increment were prepared by mixing with the different contents of surfactants. Total amount of surfactant used was varied from 1 to 3 % by volume. This study demonstrates the influence of water and surfactant contents of emulsified fuel, injection pressure on the spray characteristics, i.e. Sauter mean diameter(SMD) and spray angle. The drop size distribution of the emulsified fuel spray was measured with a Malvem particle sizer. In order to measure the spray angle, the digital image processing was employed by capturing multiple images of the spray with 3-CCD digital video camera. It was evident that the addition of water and surfactant changes fuel properties which are the key parameters influencing the atomization of the spray. The increase in surfactant content results in the decrease of SMD and the increase in spray angle. The droplets decease with increase in injection pressure, but the influence of injection pressure in this experimental condition was less important than expected. The more viscous fuel with the increase of water content exhibits the larger droplets in the centerline of the spray, and the less viscous fuel in the outer edges of the spray. The increase in axial position from the nozzle causes the spray angle to decrease. The spray angle decreases with increase in water content. This is due to increase in viscosity with increase in water content.
본 연구에서는 SN(Swirl Number)는 같지만 코어부와 스월러부의 질량유량비(m)가 다른 저선회 노즐 2종을 설계하여 상압 연소성능 시험을 수행하였다. 각 노즐에 대해 단열화염온도에 따른 연소성능 실험을 수행하였고 화염구조 특성, NOx 배출 특성, 연소진동 모드를 파악하였다. 화염구조가 크게 차이가 있었지만 CO 배츨 특성은 유사하였고 NOx 배출 특성도 화염구조보다는 연소진동과 더 큰 관련성이 있음을 보였다. 연료노즐의 위치를 변경하여 대류지연시간을 조절하면서 연소진동 및 NOx 배출 특성을 파악하였는데 대류지연시간이 연소진동 주기의 (3+4n)/4±1/4 (n=0,1,2,...) 영역에 들어올 때 진소진동이 강하게 나타나고 반대의 경우는 연소진동이 아주 약하게 발생함을 확인하였다.
액체 램제트 연소기는 흡입공기와 분무, 혼합 그리고 이에 따른 연소 등 일련의 과정에 따라 다수의 복잡한 현상들이 상호 밀접하게 관련되어 있으며, 이러한 반응 및 비반응 유동 특성을 파악하기 위해서 2차원 및 3차원 연소기 형상에 대해서 수치적 실험을 수행하였다 격자구성은 연소기에 공기를 공급하고 연료를 분무하는 공기 유입관 영역과 연소실 영역, 그리고 출구 대기 영역으로 나누어 격자를 생성시켰다. 비반응 유동해석을 통해서 연소실내의 선회영역 유동특성은 2차원과 3차원이 크게 차이가 남을 알 수 있었다. 반응 유동 해석에서는 분무 모델의 적용 유무에 따라 연소 형태가 크게 변화하였다. 연료의 분사위치를 유입관의 위쪽에 준 경우와 아래쪽에 준 두 가지 경우를 비교하였으며, 유입관의 아래쪽에 연료의 분사위치를 준 경우가 연소의 안정화에 필요한 재순환 영역으로의 연료의 유입이 잘 되어 유입관 위쪽에 연료를 분사시키는 것보다 좋은 분사위치임을 알 수 있었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.